Studying the Shear and Discharge Rate of Proteins in Microfluidic Junctions, Under Electrokinetic EffectsStudying the Shear and Discharge Rate of Proteins in Microfluidic Junctions, Under Electrokinetic Effects
الموضوعات :Babak kamali Doust Azad 1 , Sasan Asiaei 2 , Borhan Beigzadeh 3
1 - Department of Mechanical Engineering,
Iran University of Science and Technology, Iran
2 - Department of Mechanical Engineering,
Iran University of Science and Technology, Iran
3 - Department of Mechanical Engineering,
Iran University of Science and Technology, Iran
الکلمات المفتاحية: Microfluidics, Shear rate, Numerical modeling, Electroosmotic flow, Electrokinetic, Discharge rate, Hemolysis, Protein denaturation,
ملخص المقالة :
Changes of hydrodynamic parameters in microchannel branches affect the suspended biological samples in blood. To prevent denaturation and hemolysis, we have numerically investigated the effect of divergence angle on shear rate and velocity at branch entrance (discharge rate), under electroosmotic flow. In such flow, hydrodynamic properties are also affected by zeta potential at the microchannel walls. We have also studied the effect of change of zeta potential (ξ) proportion at main channel wall (ξ1) to that of branch channel (ξ2), on the discharge rate to find its maximum for different divergence angles. In the divergence angle of 60° and while zeta potential at the branch wall is equal to its value at main channel wall, the tendency of particles to pass through the branch is the highest among all examined degrees. At the zeta potential proportion of ( ξ1/ξ2 =0.5), the change of divergence angle has almost no effect on the maximum velocity in the branch. In addition, with increase of divergence angle from 60° to 150°, the shear rate at the branch will become 2.1 times higher.
[1] W. L. W. Hau, D. W. Trau, N. J. Sucher, M. Wong, and Y. Zohar, “Surface-chemistry Technology for Microfluidics,” J. Micromechanics Microengineering, Vol. 13, No. 2, pp. 272, 2003.
[2] A. D. Stroock, M. Weck, D. T. Chiu, W. T. S. Huck, P. J. A. Kenis, R. F. Ismagilov, and G. M. Whitesides, “Patterning Electro-osmotic Flow With Patterned Surface Charge,” Phys. Rev. Lett., Vol. 84, No. 15, pp. 3314, 2000.
[3] Y. Takamura, H. Onoda, H. Inokuchi, S. Adachi, A. Oki, and Y. Horiike, “LowVoltage Electroosmosis Pump for Stand Alone Microfluidics Devices,” Electrophoresis, Vol. 24, No. 1-2, January 2003, pp. 185–192.
[4] L. Bousse, C. Cohen, T. Nikiforov, A. Chow, A. R. Kopf-Sill, R. Dubrow, and J. W. Parce, “Electrokinetically Controlled Microfluidic Analysis Systems,” Annu. Rev. Biophys. Biomol. Struct., Vol. 29, No. 1, pp. 155–181, 2000.
[5] A. Ajdari, “Transverse Electrokinetic and Microfluidic Effects in Micropatterned Channels: Lubrication Analysis for Slab Geometries,” Phys. Rev. E, vol. 65, No. 1, pp. 16301, 2001.
[6] L. M. Lee, W. L. W. Hau, Y.-K. Lee, and Y. Zohar, “In-Plane Vortex Flow in Microchannels Generated by Electroosmosis With Patterned Surface Charge,” J. Micromechanics Microengineering, Vol. 16, No. 1, pp. 17, 2006.
[7] A. S. W. Ng, W. L. W. Hau, Y.-K. Lee, and Y. Zohar, “Electrokinetic Generation of Microvortex Patterns in a Microchannel Liquid Flow,” J. Micromechanics Microengineering, Vol. 14, No. 2, pp. 247, 2004.
[8] G. Whitesides and A. Stroock, “Flexible Methods for Microfluidics [J],” Phys Today, Vol. 54, No. 6, pp. 42–48, 2001.
[9] H. A. Stone, A. D. Stroock, and A. Ajdari, “Engineering Flows in Small Devices: Microfluidics Toward a Lab-On-A-Chip,” Annu. Rev. Fluid Mech., Vol. 36, pp. 381–411, 2004.
[10] D. Marro, Y. N. Kalia, M. B. Delgado-Charro, and R. H. Guy, “Contributions of Electromigration and Electroosmosis to Iontophoretic Drug delivery,” Pharm. Res., Vol. 18, No. 12, pp. 1701–1708, 2001.
[11] C. Wiles and P. Watts, “Improving Chemical Synthesis Using Flow Reactors,” 2007.
[12] A. K. Vijh, “Electrochemical Treatment of Tumors (ECT): Electroosmotic Dewatering (EOD) as the Primary Mechanism,” Dry. Technol., Vol. 17, No. 3, pp. 586–596, 1999.
[13] S. T. P. YK Ng E, “CFD Analysis of Double-Layer Microchannel Conjugate Parallel Liquid Flows With Electric Double-Layer Effects,” Numer. Heat Transf. Part A Appl., Vol. 40, No. 7, pp. 735–749, 2001.
[14] E. Y. K. Ng and S. T. Tan, “Computation of Three-Dimensional Developing Pressure-Driven Liquid Flow in a Microchannel With EDL Effect,” Numer. Heat Transf. Part A, vol. 45, No. 10, pp. 1013–1027, 2004.
[15] S. T. Tan and E. Y. K. Ng, “Numerical Analysis of EDL Effect on Heat Transfer Characteristic of 3-D Developing Flow in a Microchannel,” Numer. Heat Transf. Part A Appl., Vol. 49, No. 10, pp. 991–1007, 2006.
[16] E. Y. K. Ng and S. T. Tan, “Study of EDL Effect on 3-D Developing Flow in Microchannel With Poisson–Boltzmann and Nernst–Planck models,” Int. J. Numer. Methods Eng., Vol. 71, No. 7, pp. 818–836, 2007.
[17] H. Andersson, W. Van Der Wijngaart, P. Nilsson, P. Enoksson, and G. Stemme, “A Valve-less Diffuser Micropump for Microfluidic Analytical Systems,” Sensors Actuators B Chem., Vol. 72, No. 3, pp. 259–265, 2001.
[18] T. E. McKnight, C. T. Culbertson, S. C. Jacobson, and J. M. Ramsey, “Electroosmotically Induced Hydraulic Pumping With Integrated Electrodes on Microfluidic Devices,” Anal. Chem., vol. 73, No. 16, pp. 4045–4049, 2001.
[19] P. C. H. Li and D. J. Harrison, “Transport, Manipulation, and Reaction of Biological Cells On-Chip Using Electrokinetic Effects,” Anal. Chem., Vol. 69, No. 8, pp. 1564–1568, 1997.
[20] S. Ebrahimi, A. Hasanzadeh-Barforoushi, A. Nejat, and F. Kowsary, “Numerical Study of Mixing and Heat Transfer in Mixed Electroosmotic/Pressure Driven Flow Through T-Shaped Microchannels,” Int. J. Heat Mass Transf., Vol. 75, pp. 565–580, 2014.
[21] A. Soleymani, E. Kolehmainen, and I. Turunen, “Numerical and Experimental Investigations of Liquid Mixing in T-Type Micromixers,” Chem. Eng. J., Vol. 135, pp. S219–S228, 2008.
[22] Y. Ai, S. Park, J. Zhu, X. Xuan, A. Beskok, and S. Qian, “DC Electrokinetic Particle Transport in an L-Shaped Microchannel,” Langmuir, Vol. 26, No. 4, pp. 2937–2944, 2009.
[23] S. Bhopte, B. Sammakia, and B. Murray, “Geometric Modifications to Simple Microchannel Design for Enhanced Mixing,” In 2008 11th IEEE Intersociety Conference on Thermal and Thermomechanical Phenomena in Electronic Systems, I-THERM, 2008, pp. 937–944.
[24] E. A. Mansur, 王运东, 戴猷元, E. A. Mansur, W. Yun-Dong, and D. A. I. You-Yuan, “Computational Fluid Dynamic Simulation of Liquid− Liquid Mixing in a Static Double-T-Shaped Micromixer,” 过程工程学报, Vol. 8, No. 6, 2008.
[25] J. G. Santiago, “Electroosmotic Flows in Microchannels With Finite Inertial and Pressure Forces,” Anal. Chem., Vol. 73, No. 10, pp. 2353–2365, 2001.
[26] E. J. Lim, T. J. Ober, J. F. Edd, S. P. Desai, D. Neal, K. W. Bong, P. S. Doyle, G. H. McKinley, and M. Toner, “Inertio-Elastic Focusing of Bioparticles in Microchannels at High Throughput.,” Nat. Commun., Vol. 5, pp. 4120, 2014.
[27] L. B. Leverett, J. D. Hellums, C. P. Alfrey, and E. C. Lynch, “Red Blood Cell Damage by Shear Stress,” Biophys. J., Vol. 12, No. 3, pp. 257, 1972.
[28] O. K. Baskurt, “Red Blood Cell Mechanical Stability,” Engineering, Vol. 4, No. 10, pp. 8, 2013.
[29] G. M. Yezaz Ahmed and A. Singh, “Numerical Simulation of Particle Migration in Asymmetric Bifurcation Channel,” J. Nonnewton. Fluid Mech., Vol. 166, No. 1–2, pp. 42–51, 2011.
[30] A. N. Frumkin, O. A. Petrii, B. B. Damaskin, J. O. M. Bockris, B. E. Conway, and E. Yeager, “Comprehensive Treatise of Electrochemistry,” Vol. 1 Plenum, New York, pp. 246–251, 1980.
[31] F. F. Reuss, “Sur un Nouvel Effet De L’électricité Galvanique,” Mem. Soc. Imp. Natur. Moscou, Vol. 2, pp. 327–337, 1809.
[32] H. Bruus, Theoretical Microfluidics. OUP Oxford, 2008.
[33] D. Li, Electrokinetics in Microfluidics. Academic, 2004.
[34] R. H. Pletcher, J. C. Tannehill, and D. Anderson, Computational Fluid Mechanics and Heat Transfer, Third Edition. CRC Press, 2012.
[35] F. Bianchi, R. Ferrigno, and H. H. Girault, “Finite Element Simulation of an Electroosmotic-Driven Flow Division at a T-Junction of Microscale Dimensions,” Anal. Chem., Vol. 72, No. 9, pp. 1987–1993, 2000.
