Experimental Study on Magnetic Abrasive Honing of Inner Surface of Tube AISI304
الموضوعات :Hamzeh Shahrajabian 1 , Masoud Farahnakian 2 , Payam Saraeian 3
1 -
2 - Department of Mechanical Engineering,
Najafabad branch, Islamic Azad University, Najafabad, Iran
3 - Department of Mechanical Engineering,
Najafabad branch, Islamic Azad University, Najafabad, Iran
الکلمات المفتاحية: Honing, AISI 304, Inner surface, Surface Roughness, Magnetic abrasive,
ملخص المقالة :
To overcome the limitation of honing process, the present work proposes magnetic abrasive honing (MAH) process whereby abrasive stones are replaced by magnetic abrasives. This process is combination of magnetic abrasive finishing (MAF) and honing. MAF which is one of the finishing processes can improve the quality of workpiece surface with various geometries, removing the chips in micrometer scale by magnetic field forces. This study set to apply longitudinal vibration to the tube workpiece in MAF process; hence, this process is called MAH. The effects of rotary speed of workpiece, cross-hatch angle, and mesh number were investigated on the surface roughness of AISI 304. Magnetic abrasives were combination of SiC particles as abrasives and iron particles as ferromagnetic particles in lubricant of SAE 40 oil. The results revealed that the longitudinal movement of workpiece is effective on MAH, as the surface roughness decreased with increasing the cross-hatch angle. Surface roughness decreased with increase of rotary and mesh number. The major changes in surface roughness (58%) were obtained in cross-hatch angle of 45º rotary speed of 800 rpm and mesh size of 400. The microscopic picture showed that three-body wear mechanism is dominant for fine grits.
[1] Shinmuram, T., Takazawa, K., Hatano, E. and Matsunaga, M., Study on Magnetic Abrasive Finishing, Annals of CIRP, Vol. 39, No. 1, 1990, pp. 325-328.
[2] Yamaguchi, H., Shinmura, T., Study of the Surface Modification Resulting from an Internal Magnetic Abrasive Finishing Process, Wear, Vol. 225-229, Part 1, 1999, pp. 246-255.
[3] Shaohui, Y., Takeo, Sh. A., Comparative Study: Polishing Characteristics and Its Mechanisms of Three Vibration Modes in Vibration-Assisted Magnetic Abrasive Polishing, International Journal of Machine Tools and Manufacture, Vol. 44, No. 4, 2004, pp. 383–390.
[4] Givi, M., Fadaei, A. and Mohammadi, A., Polishing of the Aluminum Sheets with Magnetic Abrasive Finishing Method, The International Journal of Advanced Manufacturing Technology, Vol. 61, No. 9, 2012, pp. 989-998.
[5] Zhou, K., Chen, Y., Du, Z. W. and Niu, F. L., Surface Integrity of Titanium Part by Ultrasonic Magnetic Abrasive Finishing, The International Journal of Advanced Manufacturing Technology, Vol. 80, No. 5, 2015, pp. 997-1005.
[6] Du, Z. W., Chen, Y., Zhou, K. and Li, C., Research on the Electrolytic-Magnetic Abrasive Finishing of Nickel-Based Superalloy GH4169, International Journal of Advanced Manufacturing Technology, Vol. 81, No. 5–8, 2015, pp. 897–903.
[7] Saraeian, P., Soleimani Mehr H., Moradi, B., Tavakoli, H. and Alrahmani, K. h., Study of Magnetic Abrasive Finishing for AISI321 Stainless Steel, Materials and Manufacturing Processes, Vol. 31, No. 15, 2016, pp. 2023-2029.
[8] Judal, K. B., Yadava, V. and Pathak, D., Experimental Investigation of Vibration Assisted Cylindrical Magnetic Abrasive Finishing of Aluminum Workpiece, Materials and Manufacturing Processes, Vol. 28, No. 11, 2013, pp. 1196-1202.
[9] Cheng, W. A., Tsai, L., Liu, C. H., Liang, K. Z. and Lee, S. J., Elucidating the Optimal Parameters in Magnetic Finishing with Gel Abrasive, Materials and Manufacturing Processes, Vol. 26, No. 5, 2011, pp. 786-791.
[10] Judal, K. B., Yadava, V., Experimental Investigation into Electrochemical Magnetic Abrasive Machining of Cylindrical Shaped Nonmagnetic Stainless Steel Workpiece, Materials and Manufacturing Processes, Vol. 28, No. 10, 2013, pp. 1095-1101.
[11] Choopani, Y., Razfar, M. R., Saraeian, P., Farahnakian, M., Experimental Investigation of External Surface Finishing of AISI 440C Stainless Steel Cylinders using the Magnetic Abrasive Finishing Process, The International Journal of Advanced Manufacturing Technology, Vol. 83, No. 9–12, 2015, pp. 1811–1821.
[12] Biing Hwa, Y., Hsinn Jyh, T., Fuang, Y. H., Yan Cherng, L. and Han Ming, Ch., Finishing Effects of Spiral Polishing Method on Micro Lapping Surface, International Journal of Machine Tools and Manufacture, Vol. 47, No. 6, 2007, 920-926.
[13] Yamaguchi, H., Srivastava, A. K., Tan, M. and Hashimoto, F., Magnetic Abrasive Finishing of Cutting Tools for High-Speed Machining of Titanium Alloys, CIRP Journal of Manufacturing Science and Technology, No. 7, No. 4, 2014, pp. 299-304.
[14] Zo, Y., Shinmura, T., Development of a New Magnetic Field Assisted Deburring Technology for Inside Surface using Permanent Magnets and Magnetic Particles (Machining Principle and a Few Deburring Characteristics), Journal of the Japan Society for Abrasive Technology, Vol. 51, No. 2, 2007, pp. 94-99.
[15] Kim, T. W., Kwak, J. S., A Study on Deburring of Magnesium Alloy Plate by Magnetic Abrasive Polishing, International Journal of Precision Engineering and Manufacturing, Vol. 11, No. 2, 2010, pp. 189‐194.
[16] Ko, S. L., Baron, Y. M. and Park, J. I., Micro Deburring for Precision Parts Using Magnetic Abrasive Finishing Method, Journal of Materials Processing Technology, Vol. 187–188, 2007, 19–25.
[17] Ching Lien, H., Wei Liang, K. and Lieh Dai, Y., Prediction System of Magnetic Abrasive Finishing (MAF) on the Internal Surface of a Cylindrical Tube, Materials and Manufacturing Processes, Vol. 25, No. 12, 2010, pp.1404–1412.
[18] Yun, H., Han, B., Chen, Y. and Liao, M., Internal Finishing Process of Alumina Ceramic Tubes by Ultrasonic-Assisted Magnetic Abrasive Finishing, The International Journal of Advanced Manufacturing Technology, Vol. 85, No. 1–4, 2015, pp. 727–734.
[19] Shinmura, T., Yamaguchi, H., Study on a New Internal Finishing Process by the Application of Magnetic Abrasive Machining-Internal Finishing of Stainless Steel Tube and Clean Gas Bomb, The Japan Society of Mechanical Engineers, Vol. 38, No. 4C, 1995, pp. 798–804.
[20] Khalaj, A., S., Fadaei T. A., Mossadegh, P. and Mohammadi, A., A Comprehensive Experimental Study on Finishing Aluminum Tube by Proposed UAMAF Process, Materials and Manufacturing Processes, Vol. 30, No. 1, 2015, pp. 93-98.
[21] Yamaguchi, H., Shinmura, T., Study of an Internal Magnetic Abrasive Finishing Using a Pole Rotation System Discussion of the Characteristic Abrasive Behavior, Journal of the International Societies for Precision Engineering and Nanotechnology, No. 24, No. 3, 2000, pp. 237-244.
[22] Wang, Y., Hu, D., Study on the Inner Surface Finishing of Tubing by Magnetic Abrasive Finishing, International Journal of Machine Tools and Manufacture, Vol. 45, No. 1, 2005, pp. 43-49.
[23] Wang, D., Shinmura, T. and Yamaguchi, H., Study of Magnetic Field Assisted Mechanochemical Polishing Process for Inner Surface of Si3N4 Ceramic Components Finishing Characteristics Under Wet Finishing using Distilled Water, International Journal of Machine Tools and Manufacture, Vol. 44, No. 14, 2004, pp. 1547-1553.
[24] Yamaguchi, H., Shinmura, T. and Kobayashi, A., Development of an Internal Magnetic Abrasive Finishing Process for Nonferromagnetic Complex Shaped Tube, The Japan Society of Mechanical Engineers, No. 44, No.1C, 2001, pp. 275-281.
