Design and Simulation of Two Low-Voltage, Low-Power Transresistance Instrumentation Amplifiers with Electronic Adjustment Capability
الموضوعات :
Yasin Safari
1
,
S. Mohammadali Zanjani
2
1 - Department of Electrical Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran.
2 - Department of Electrical Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran.
الکلمات المفتاحية: Instrumentation amplifier, Current mode, Transresistance mode, Common mode rejection ratio (CMRR),
ملخص المقالة :
This article introduces two designs for transresistance amplifiers. The first and second precision instrument amplifiers utilize ten and eight MOS transistors. Both proposed precision amplifiers were simulated with 0.18 µm CMOS technology and a supply voltage of ±0.7 V using Hspice software. According to the results, the Common Mode Rejection Ratio (CMRR) of the first precision amplifier can vary from 72.6 dB to 75.7 dB with a change in control voltage. In contrast, the second amplifier can range from 71.7 dB to 74 dB. The -3dB cutoff frequency for the CMRR of the first precision amplifier is accessible between 0.969 MHz and 16.4 MHz, and for the second precision amplifier, it ranges from 4.34 MHz to 40.8 MHz. The power consumption of the first proposed design varies from 203.33 µW to 372.77 µW within the adjustment range, and for the second proposed design, it changes from 234.57 µW to 338.73 µW. Time-domain analysis indicates that for a 20 µA(p-p) input signal, the maximum Total Harmonic Distortion (THD) at various frequencies for the first design is 3.37%. For the second design, it is 2.13%. The output impedance of the first proposed precision amplifier can vary from 779 to 1190 Ω with a change in control voltage, and for the second proposed amplifier, it can change from 860 Ω to 1640 Ω. Therefore, these two circuits are suitable for precision amplifier applications with electronic adjustability in medical instruments, biosensor reading circuits, electrocardiography, and signal processing.
[1] A. Baghi-Rahin, V. Baghi-Rahin, “A 0.5 V operational transconductance amplifier based on dynamic threshold-voltage MOSFET and floating gate MOSFET inverters in 180 nm CMOS technology,” Journal of Intelligent Procedures in Electrical Technology (JIPET), Vol. 15, no. 60, pp. 1-18, March 2025 (in Persian).
[2] L. Safari, & S. Minaei, “A novel resistor-free electronically adjustable current-mode instrumentation amplifier,” Circuits, Systems and Signal Processing, 32(3):1025–1038, 2013.
[3] E. Yuce, “Various current-mode and voltage-mode instrumentation amplifier topologies suitable for integration,” Journal of Circuits, Systems, and Computers, 19(3):689–699, 2011.
[4] A. Baghi Rahin, and V. Baghi Rahin, “A new 2-input CNTFET-based XOR cell with ultra-low leakage power for low-voltage and low-power full adders,” Journal of Intelligent Procedures in Electrical Technology (JIPET), 10(37), pp. 2322-3871, 2019
[5] Zanjani, S. M. A., & Parvizi, M. (2021). Design and simulation of a bulk driven operational trans-conductance amplifier based on CNTFET technology. Journal of Intelligent Procedures in Electrical Technology (JIPET),12(45), 65-76.
[6] W. J. K. Michiel, and A. P. Pertij, “A 140dB-CMRR current-feedback instrumentation amplifier employing ping-pong auto-zeroing”, IEEE Int. Solid-State Circuits Conf. (2009), San Francisco, USA, pp. 324–325, 2009.
[7] T. Ettaghzouti, M. Bchir, & N. Hassen, “High CMRR voltage mode instrumentation amplifier using a new CMOS differential difference current conveyor realization,” International Journal of Electrical Engineering & Telecommunication, vol. 9, no. 3, pp. 132–141, 2020.
[8] S. Maheshwari, “High CMRR wide bandwidth instrumentation amplifier using current controlled conveyors,” Int. J. Electron, 89, 889–896, 2008.
[9] A. Baghi Rahin, Z. Daei Koozeh Kanani, “A Low-Voltage and Low-Power Programmable Gm-C Filter for Wireless Applications,” Journal of Intelligent Procedures in Electrical Technology (JIPET), Vol. 5(19), Dec. 2014, pp. 3-10.
[10] L. Safari, S. Minaei, “A novel COA-based electronically adjustable current-mode instrumentation amplifier topology,” AEU-Int J Electron Commun, 82, 285–93, 2017.
[11] L. Safari, S. Minaei, G. Ferri, & V. Stornelli, “Analysis and design of a new COA-based current-mode instrumentation amplifier with robust performance against mismatches,” AEU-Int J Electron Commun, 89,105–9, 2018.
[12] B. Chaturvedi, & A. Kumar, “Electronically tunable current-mode instrumentation amplifier with high CMRR and wide bandwidth,” AEU-Int J Electron Commun, 92, 116–23, 2018.
[13] C. Chanapromma, C. Tanaphatsiri, and M. Siripruchyanun, “An electronically controllable instrumentation amplifier based on CCCCTAs,” IEEE Int. Symp. Intelligent Signal Processing and Communications Systems (ISPACS2008), Bangkok, Thailand, pp. 1–4. (2009)
[14] N. Raj, S. Dutta, R. K. Ranjan, & et al., “VDTA Based Transadmittance Mode Instrumentation Amplifier with Experimental results,” 2023.
