Investigating the Effect of Process Parameters on Reducing the Peeling Stress in Adhesive Joints of Composite Materials

Subject Areas : composite materials

Saeed  Yaghoubi ¹ (Department of Mechanical Engineering, Faculty of Engineering, Ilam University, Ilam, Iran)
Mohammad  Shishehsaz ² (Department of Mechanical Engineering, Faculty of Engineering, Shahid Chamran University of Ahvaz, Ahvaz, Iran)
Kiamehr  Rouzbakhshzadeh ³ (Department of Mechanical Engineering, Faculty of Engineering, Shahid Chamran University of Ahvaz, Ahvaz, Iran)

Received: 2022-10-19 Accepted : 2023-01-20 Published : 2023-06-01

Keywords: Adhesive Joint, Interlayer Normal Stress, Optimization Algorithms, Adhesive, Adherend,

Abstract :

Joints are considered the weakest part of an engineering structure and failure usually occurs in this region, firstly. One of the main factors in the rupture of adhesive joints is the normal stresses between the layers created by the presence of an out-of-center load and bending moment. The present research work has focused on the influence of parameters including the adhesive zone length, adhesive and adherend layer thickness on reducing the amount of normal interlayer stress in a single-lap adhesive joint. Optimization of parameters have been done using BA and PSO optimization algorithm. The distribution of normal and shear stresses are based on two-dimensional elasticity theory that includes the complete stress-strain and strain-displacement relations for the adhesive and adherends. The results obtained from current research revealed that by optimization of mentioned parameters, the value of peeling stress is significantly reduced. Although increasing in Young’s modulus of adhesive layer leads to an increase in normal stress of the joint, it creates a more uniform stress distribution at the edges. The outcomes also revealed that increasing the length of the joint zone and the thickness of adherends can improve the interlayer normal stress in the adhesive joint.

References:

• Lee, J., Bae, D., Chung, W., Kim, K., Lee, J., and Cho, Y., Effects of Annealing on the Mechanical and Interface Properties of Stainless Steel/Aluminum/Copper Clad-Metal Sheets, Journal of Materials Processing Technology, Vol. 187, 2007, pp. 546-549, https://doi.org/10.1016/j.jmatprotec.2006.11.121.


• Li, L., Nagai, K., and Yin, F., Progress in Cold Roll Bonding of Metals, Science and Technology of Advanced Materials, Vol 9, No. 2, 2008, pp. 023001, https://doi.org/10.1088/1468-6996/9/2/023001.


• Manesh, H. D., Shahabi, H. S., Effective Parameters on Bonding Strength of Roll Bonded Al/St/Al Multilayer Strips, Journal of Alloys and Compounds, Vol. 476, No. 1-2, 2009, pp. 292-299, https://doi.org/10.1016/j.jallcom.2008.08.081.


• Shishehsaz, M., Yaghoubi, S., The Effect of Fiber Breakage on Transient Stress Distribution in a Single-Lap Joint Composite Material, Journal of Solid Mechanics, Vol. 7, No. 4, 2015, pp. 442-57, https://dorl.net/dor/20.1001.1.20083505.2015.7.4.6.3.


• Hart-Smith, L., Design of Adhesively Bonded Joints, Elsevier Applied Science Publishers Ltd, Joining Fibre-Reinforced Plastics, 1987, pp. 271-311.


• Molitor, P., Barron, V., and Young, T., Surface Treatment of Titanium for Adhesive Bonding to Polymer Composites: A Review, International Journal of Adhesion and Adhesives, Vol. 21, No. 2, 2001, 129-136, https://doi.org/10.1016/S0143-7496(00)00044-0.


• Zhao, B., Lu, Z. H., A Two-Dimensional Approach of Single-Lap Adhesive Bonded Joints, Mechanics of Advanced Materials and Structures, Vol. 16, No. 2, 2009, pp. 130-59, https://doi.org/10.1080/15376490802625464.


• Bavi, O., Bavi, N., and Shishesaz, M., Geometrical Optimization of the Overlap in Mixed Adhesive Lap Joints, The Journal of Adhesion, Vol. 89, No. 12, 2013, pp. 948-972 https://doi.org/10.1080/00218464.2013.782813.


• Shishehsaz, M., Moradi, S., and Yaghoubi, S., Transient Stress Analysis In Adhesive Single Lap Joints of a Composite Material Due To Fiber Breakage, Journal of Solid and Fluid Mechanics, Vol. 4, No. 4, 2015, pp. 113-126, https://doi.org/10.22044/jsfm.2015.398.


• Selahi, E., Semi Analytical Transient Dynamic Analysis of Composite Adhesive Single-lap Joints, Mechanics of Advanced Composite Structures‎, Vol. 7, No. 1, 2020, pp. 137-145. https://dx.doi.org/10.22075/macs.2019.16036.1161,


• Wang, S., Liang, W., Duan, L., Li, G., and Cui, J., Effects of Loading Rates on Mechanical Property and Failure Behavior of Single-Lap Adhesive Joints with Carbon Fiber Reinforced Plastics and Aluminum Alloys, The International Journal of Advanced Manufacturing Technology, Vol. 106, No. 5, 2020, pp. 2569-2581. https://doi.org/10.1007/s00170-019-04804-w.


• de Miguel, A., Pagani, A., Rizzo, L., Catapano, A., and Panettieri, E., Accurate Evaluation of 3D Stress Fields in Adhesive Bonded Joints Via Higher-Order FE Models, Mechanics of Advanced Materials and Structures, Vol. 27, No. 4, 2020, pp. 333-345, https://doi.org/10.1080/15376494.2018.1472352.


• Polini, W., Corrado, A., Effect of Adherends Misalignment on the Strength of Single-Lap Bonded Joints, The International Journal of Advanced Manufacturing Technology, Vol. 106, No. 3, 2020, pp. 817-828, https://doi.org/10.1007/s00170-019-04652-8.


• Beigrezaee, M., Ayatollahi, M., Bahrami, B., and Da Silva, L., A New Geometry for Improving the Strength of Single-Lap Joints Using Adherend Notching Technique, The Journal of Adhesion, Vol. 97, No. 11, 2021, pp. 1004-1023, https://doi.org/10.1016/j.tafmec.2022.103364.


• Peres, L., Arnaud, M., Silva, A., Campilho, R., Machado, J., and Marques, E., Geometry and Adhesive Optimization of Single-Lap Adhesive Joints Under Impact, The Journal of Adhesion, Vol. 98, No. 6, 2022, pp. 677-703, https://doi.org/10.1080/00218464.2021.1994404.


• Marchione, F., Effect of Hollow Adherends on Stress Peak Reduction in Single-Lap Adhesive Joints: FE and Analytical Analysis, The Journal of Adhesion, Vol. 98, No. 6, 2022, pp. 656-676, https://doi.org/10.1080/00218464.2021.1995368.


• Zhao, B., Lu, Z. H., and Lu, Y. N., Closed-Form Solutions for Elastic Stress–Strain Analysis in Unbalanced Adhesive Single-Lap Joints Considering Adherend Deformations and Bond Thickness, International Journal of Adhesion and Adhesives, Vol. 31, No. 6, 2011, 434-445, https://doi.org/10.1016/j.ijadhadh.2011.03.002.


• Cheng, S., Chen, D., and Shi, Y., Analysis of Adhesive-Bonded Joints with Nonidentical Adherends, Journal of Engineering Mechanics, Vol. 117, No. 3, 1991, pp. 605-623, https://doi.org/10.1061/(ASCE)0733-9399(1991)117:3(605).


• Pham, D., Ghanbarzadeh, A., Otri, S., and Koç, E., Optimal Design of Mechanical Components Using the Bees Algorithm, Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, Vol. 223, No. 5, 2009, pp. 1051-1056, https://doi.org/10.1243/09544062JMES838.


• Zhou, C., Gao, H., Gao, L., and Zhang, W., Particle Swarm Optimization (PSO) Algorithm, Application Research of Computers, Vol. 12, 2003, pp. 7-11.