Efficiency Estimation of Olefin Furnaces in Order to Provide Methods for Increasing the Efficiency

Subject Areas : Mechanical Engineering

Jamaledin Binanejad ¹ , Amir Homayoon Meghdadi Isfahani ²

1 - Department of Mechanical Engineering, Najafabad branch, Islamic Azad University, Najafabad, Iran
2 - Department of Mechanical Engineering, Najafabad branch, Islamic Azad University, Najafabad, Iran Modern Manufacturing Technologies Research Center, Najafabad Branch, Islamic Azad University, Najafabad, Iran

Received: 2019-01-21 Accepted : 2019-05-10 Published : 2019-09-01

Keywords: Steak, Thermography, Cracking, Optimization, Energy Dissipation, Furnace Efficiency,

Abstract :

Despite the growing trend in the petrochemical industry in the country, the industry has faced challenges and accomplishments. One of the most important challenges in the petrochemical industry is energy management in the refinery. Fajr Jam refinery is designed to refine part of sour gas produced from Phase 6 of South Pars gas field in Iran and the nominal capacity of gas refining at this site, to determine the factors affecting energy consumption in the ophthalmic furnaces, 104 and 109 kilns were selected and the following were monitored scientifically: monitoring of furnace wall temperature with thermography, furnace feed analysis, steak gas analysis and energy efficiency of furnaces. The results of this study showed that in the furnace 104, the design efficiency and real efficiency was 92.98 and 84.67, respectively and for the furnace 109, the design efficiency and real efficiency was 94.98 and 71.18, respectively. As a result, the amount of energy loss is high and should save energy consumption in these furnaces and improve efficiency: replacement of refractory refractories is also a replacement of insulation.

References:

[1]    Gupta, A. K., Technological Evolution, Challenges and Future Prospects for the Application of HiTAC in the HiCOT Project, Proceeding of the Forum on High-Temperature Air Combustion Technology, 2001.

[2]     Heynderickx, G. J., Froment, F., Simulation and Comparison of the Run Length of an Ethane Cracking Furnace with Reactor Tubes of Circular and Elliptical Cross, Industrial and Engineering Chemistry Research, Vol. 37, 1998, pp. 914-922.

[3]     Meng D, Shao C, Zhu L, Ethylene Cracking Furnace TOPSIS Energy Efficiency Evaluation Method based on Dynamic Energy Efficiency Baselines, Energy, Vol. 156, 2018, 620-634.

[4]    Han S. H., Lee Y. S., Cho J. R., Lee, K. H., Efficiency Analysis of Air-Fuel and Oxy-Fuel Combustion in A Reheating Furnace, International Journal of Heat and Mass Transfer, Vol. 121, 2018, 1364-1370.

[5]     Magrekchi, S., Energy Management Principles, 2000. 

[6]    Morita, M., Optimal Design for High Performance Industrial Furnace Applied High Temperature Air Combustion Technology, Proceeding of 2000 International Joint Power Generation Conference, Vol. IJPGC2000-15030, 2000. 

[7]    Sabounchi, A., Emadi, A., and Taheri, M., Investigation of the Effect of Hot Charge on the Specific Energy Consumption and Capacity of Steel Furnace Furnaces using Thermal Simulation, 20th Annual Conference of Mechanical Engineering, Shiraz, 2013.

[8]    Schmit C, Guideline, Inspection of High Temperature Radiant Colis Operating In Pyrolysis Furnaces –Co. 2010.

[9]     Szecowka, L., Poskart, M., Numerical Modelling of Nitrogen Oxide Emission and Experimental Verification, Third Mediteranean Combustion Symposium, Marrakech, Maroko, 2003.

[10]  Towfighi, M., Sardameli, A., and Niaeiv, R., The Combined Simulation of Heat Transfer and Pyrolysis Reactions in Industrial Cracking Furnaces- Applied Thermal Engineering, Applied Thermal Engineering, Vol. 24, No. 14-15, 2004, pp. 2251–2265.

[11] Ziarifar, E., Zarin Abadi S., Transport Phenomena, Byron B., Warren S., Edvin L., Translated Ahvaz University. 2009.