Experimental and Numerical Study of In-Plane Loading of Thin-Walled Tubes with Different Section Shapes and Wall Thickness

محورهای موضوعی : Mechanical Engineering

sajjad dehghanpour ¹ (Department of Mechanical Engineering, Tuyserkan Branch, Islamic Azad University, Tuyserkan, Iran)
Ali Alavi Nia ² (Department of Mechanical Engineering, Bu-Ali Sina University, Hamedan, Iran)

تاریخ دریافت : 1400/10/05 تاریخ پذیرش : 1401/02/03 تاریخ انتشار : 1401/06/10

کلید واژه: Thin-walled tube, In-plane loading, peak load, energy absorption, Quasi-Static,

چکیده مقاله :

In this paper, deformations and energy absorption capacities of thin-walled tubes with different section geometries (circle, square, rectangle, hexagon and triangle) under quasi-static in-plane loading are investigated. The tubes have the same material properties, mass, volume, lengths and average section area and the loading conditions are similar for all of the specimens. In order to investigate the behaviour of the tubes, more than 100 tests are carried out and numerical simulations are performed. The numerical results are in good agreement with experimental data and show that the section geometry has an important effect on energy absorption capacity so that the circular and square sections have the least and the most capability of energy absorption, respectively. Furthermore, for a specific tube, the absorbed energy increases with the wall thickness. The first peak load in load-displacement curves has the greatest and the smallest values for rectangular and circular sections, respectively.

منابع و مأخذ:

• Mutchler, L. D., Energy Absorption of Aluminum Tubing, Trans, ASME, 1. App. Mech, Vol. 27, 1960, pp. 740-743.


• Deruntz Jr, J. A, Hodge Jr, P. G., Crushing of a Tube Between Rigid Plates, J. Appl. Mech., Vol. 30, 1963, pp. 391-398.


• Reid, S. R., Reddy, T. Y., Effect of Strain Hardening on The Lateral Compression of Tubes Between Rigid Plates, Inl. J. Sol ids Struc, Vol. 14, No. 3, 1978, pp. 213-225.


• Reddy, T. Y., Reid, S. R., Lateral Compression of Tubes and Tube-System with Side Constrains, Int. 1. Mech. Sci. Vol. 21, No. 3, 1979, pp. 187-199.


• Sinha, D. K., Chitkara, N. R, Plastic Collapse of Square Rings, Int. J. Solid Struc, Vol. 18, No. 9, 1982, pp. 819-826.


• Kecman, D., Bending Collapse of Rectangular and Square Section Tubes, Int. J. Mech. Sci, Vol. 25, No. (9-10), 1983, pp. 623-636.


• Gupta, N. K, Khullar, A., Collapse of Square and Rectangular Tubes in Transverse Loading, Arch. Appl. Mech, Vol. 63, No. 7, 1993, pp. 479-490.


• Gupta, N. K., Sekhon, G. S., and Gupta, P. K., A Study of Lateral Collapse of Square and Rectangular Metallic Tubes, Thin-Walled Struc, Vol. 39, No. 9, 2001, pp. 745-772.


• Gupta, N. K., Sekhon, G. S., and Gupta, P. K., Study of Lateral Compression of Round Metallic Tubes, Thin-Walled, Vol. 43, No. 6, 2005, pp. 895-922.


• Morris, E., Olabi, A. G., and Hashmi, M. S. J., Analysis of Nested Tube Type Energy Absorbers with Different Indenters and Exterior Constraints, Thin-Walled Struc, Vol. 44, No. 8, 2006, pp. 872-885.


• Kheirikhah, M. M., Dehghanpour, S., and Rahmani, M., Quasi-Static Axial Compression of thin-walled Circular Composite Tubes, Journal of Structural Engineering and Geo-Techniques, Vol. 6, No. 1, 2016, pp. 9-13.


• Dehghanpour, S., Rahmani, M., Experimental and Numerical Study of Lateral Collapse of Square and Rectangular Composite Tubes, Proceedings of the World Congress on Mechanical, Chemical, and Material Engineering, Barcelona, Spain, July 2015, pp. 352.


• Dehghanpour, S., Rahmani, M., Experimental and Numerical Study of Lateral Loadings on the Composite Tubes with SMA and Aluminum Wires and Without Wire, ADMT Journal, Vol. 14, No. 22021, pp. 15-22.


• Dehghanpour, S., Hosseini Safari, K., Barati, F., and Attar, M. M., Comparative Analysis of Energy Absorption Capacity of Single and Nested Metal Matrix Composite Tubes Under Quasi-Static Lateral and Axial Loading, Journal of Solid Mechanics,Vol. 13, No. 2, 2021, pp. 134-143.