Study on the Wear of Hardened Opener Shares of the Grain-Fertilizer-Grass Seeder

محورهای موضوعی : Transportation Analysis

Sayakha Orazovich Nukeshev ¹ , Dimitar P. Karaivanov ² , Nikolai N. Romanyuk ³ , Dinara Kossatbekova ⁴

1 - Department 'Technological Machines and Equipment', Technical faculty, S.Seifullin Kazakh Agrotechnical University, Nur-Sultan, Kazakhstan
2 - Applied Mechanics Department, University of Chemical Technology and Metallurgy Sofia, Sofia, Bulgaria
3 - Department of Mechanics of Materials and Machine Parts, Belarus State Agrarian Technical University, Minsk, Belarus
4 - Department 'Technological Machines and Equipment', Technical faculty, S.Seifullin Kazakh Agrotechnical University, Nur-Sultan, Kazakhstan

تاریخ دریافت : 1403/12/16 تاریخ پذیرش : 1404/04/14 تاریخ انتشار : 1404/04/13

کلید واژه: Abrasion, Coatings, Hardness, Surface treatments, Tribological systems, Wear,

چکیده مقاله :

The importance of this study lies in the fact that the wear of the working bodies of seeding machines leads to an increase in fuel consumption, which results in increased costs and a deterioration in the quality of seeding, thus leading to a decrease in yield. This paper aims at studying the state of hardened working bodies of a grain-fertilizer-grass seeder. Based on the results of existing information and the possibility of further implementation of shared hardening technologies, the following methods of improving wear resistance were adopted – (i) electric arc surfacing with hard-alloy electrodes and Sormayt®, and (ii) hardening share by high-frequency heat treatment. To carry out this study, samples of the opener shares of a grain-fertilizer-grass seeder, made of the structural spring steel 65Mn, were used. An ultrasonic flaw detector was used to study the condition of the worn-out surface layer of the opener shares. These studies allowed us to establish that the strengthened samples increase the hardness of the material. On the basis of experiments with rotatable central composite design, the optimal parameters for achieving maximum hardness of the grain-fertilizer-grass seeder’s opener share were determined the material composition; a soaking time and a resistivity. Under these conditions, the hardness of the steel reached 94.46 HRC. Based on these results, it is recommended to replace the standard factory heat treatment with surfacing of the entire working part of the seeder openers with T590 electrodes to achieve the best shares of hardening for use in agricultural enterprises.

چکیده انگلیسی:

The importance of this study lies in the fact that the wear of the working bodies of seeding machines leads to an increase in fuel consumption, which results in increased costs and a deterioration in the quality of seeding, thus leading to a decrease in yield. This paper aims at studying the state of hardened working bodies of a grain-fertilizer-grass seeder. Based on the results of existing information and the possibility of further implementation of shared hardening technologies, the following methods of improving wear resistance were adopted – (i) electric arc surfacing with hard-alloy electrodes and Sormayt®, and (ii) hardening share by high-frequency heat treatment. To carry out this study, samples of the opener shares of a grain-fertilizer-grass seeder, made of the structural spring steel 65Mn, were used. An ultrasonic flaw detector was used to study the condition of the worn-out surface layer of the opener shares. These studies allowed us to establish that the strengthened samples increase the hardness of the material. On the basis of experiments with rotatable central composite design, the optimal parameters for achieving maximum hardness of the grain-fertilizer-grass seeder’s opener share were determined the material composition; a soaking time and a resistivity. Under these conditions, the hardness of the steel reached 94.46 HRC. Based on these results, it is recommended to replace the standard factory heat treatment with surfacing of the entire working part of the seeder openers with T590 electrodes to achieve the best shares of hardening for use in agricultural enterprises.

منابع و مأخذ:

[1] Petukhov, D.A., Chaplygin, M.E., Nazarov, A.N. (2013). Technology and equipment for the village. Innovative Projects, New Technologies and Equipment, 4, 10-14. (in Russian)
[2] Akhmetshin, T.F. (2013). Increasing the durability of tillage working bodies moving in an abrasive soil environment. Bulletin of BSAU, 4, 76-81. (in Russian)
[3] Bartenov, I.M., Pozdnyakov, E.V. (2013). The wearing capacity of soils and its effect on the durability of the working bodies of tillage machines. Machinery and equipment/Forestry Journal, 3, 114-123. (in Russian)
[4] Chabotarev, M.I., Kadyrov, M.R. (2016). The choice of the optimal way to restore the worn surface of the part: textbook tutorial. Krasnodar: KubSAU, 91 p. (in Russian)
[5] Chernyak, I.M., Krivorudchenko, V.F., Zimina, N.V. (2000). Design of processes for welding and surfacing of car parts. Rostov State University of Railways, 32 p. (in Russian)
[6] Eltsov, V.V. (2015). Restoration and hardening of machine parts: electronic tutorial. Togliatti: TSU Publishing House, 335 p. (in Russian)
[7] Ishkov, A.V., Krivochurov, N.T., Mishutsin, N.M., Ivanaisky, V.V., Maksimov, A.A. (2010). Influence of technological factors on the wear of surface-hardened lancet paws. Technologies and Means of Agricultural Mechanization, 10, 92-96. (in Russian)
[8] Jankauskas, V., Katinas, E., Pusvaskis, M., Leisys. R. (2020). A study of the durability of hardened plough point. Journal of Friction and Wear, 41, 78-84. Doi: 10.3103/S1068366620010171
[9] Lyalakin, V.P., Aulov, V.F., Ishkov, A.V., Krivochurov, N.T., Ivanaisky, V.V., Sokolov, A.V., Koval, D.V., Dreyer, H., Shvamm, V. (2014). Wear of the bits of the anchor openers of the Primera DMC-9000 seeder, reinforced with combined coatings, in the conditions of the Altai Territory. Technologies and Means of Agricultural Mechanization, 12, 124-132. (in Russian)
[10] Malvajerdi, S.S., Malvajerdi, A.S., Ghanaatshoar, M. (2019). Protection of CK45 carbon steel tillage tools using TiN coating deposited by an arc-PVD method. Ceramics International, 45(3), 3816-3822. https://doi.org/10.1016/j.ceramint.2018.11.051
[11] Napiorkowski, J., Lemecha, M., Konat, L. (2019). Forecasting the wear of operating parts in an abrasive soil mass using the Holm-Archard Model. Materials, 12(13), 2180. Doi: 10.3390/ma12132180
[12] Novikov, A.E., Motorin, V.A., Lamskova, M.I., Filimonov, M.I. (2018). Composition and tribological properties of hardened cutting blades of tillage machines under abrasive deterioration. Journal of Friction and Wear, 39(2), 158-163. https://doi.org/10.3103/S1068366618020137
[13] Refai, M., Hamid, Z.A., El-kilani, R.M., Nasr, G.E.M. (2020). Reducing the wear and corrosion of the agricultural machinery by electrode position nanocomposite coatings: A Review. Egyptian Journal of Chemistry, 63(8), 3075-3096. https://doi.org/10.21608/EJCHEM.2020.28677.2615
[14] Roy, S., Sundararajan, S. (2016). The effect of heat treatment routes on the retained austenite and Tribomechanical properties of carburized AISI 8620 steel. Surface & Coatings Technology, 308, 236-243. https://doi.org/10.1016/j.surfcoat.2016.06.095
[15] Spiridonov, A.A. (1981). Planning an experiment in the study of technological processes. Moscow: Mechanical Engineering, 184 p. (in Russian)
[16] Stawicki, T., Bialobrzeska, B., Kostencki, P. (2017). Tribological properties of plough shares made of pearlitic and martensitic steels. Metals, 7(4), 139. https://doi.org/10.3390/met7040139
[17] Vladut, V., Marin, E., Grigore, I., St Biris, S., Ungureanu, N., Gheorghe, G., Matache, M., Persu, C., Voicea, I., Cujbescu, D., Bungescu, S., Kiss, I., Vlad, C. (2017). Field and laboratory wear testing of integral seedbed implement's chisel tines point. Actual Tasks on Agricultural Engineering, 45, 131-140.
[18] Vladutoiu, L., Vladut, V., Voiculescu, I., Matache, M., Radu, O., Biris, S., Voicea, I., Paraschiv, G., Atanasov, A., Usenko, M. (2015). Increasing agricultural machinery active parts durability by hardening. Actual Tasks on Agricultural Engineering, 43, 153-164.
[19] Wang, F.L., Tao, Q., Xiao, L.Q., Hu, J.H., Xu, L.L. (2018). Simulation and analysis of serrated chip formation in cutting process of hardened steel considering ploughing-effect. Journal of Mechanical Science and Technology, 32(5), 2029-2037. https://doi.org/10.1007/s12206-018-0411-6
[20] Yazici, A. (2011). Wear behavior of carbonitride-treated ploughshares produced from 30MNB5 steel for soil tillage applications. Metal Science and Heat Treatment, 53(5-6), 248-253. https://doi.org/10.1007/s11041-011-9377-z
[21] Yazici, A., Cavdar, U. (2017). A study of soil tillage tools from boronized sintered iron. Metal Science and Heat Treatment, 58(11-12), 753-757. https://doi.org/10.1007/s11041-017-0091-3
[22] Zhang, J.W., Zhu, L., Chen, P.; Wu, Q.M., Wei, M., Yin, C.L., Li, G.L. (2020). Flowing interaction between cutting edge of ploughbreast with soil in shifting tillage operations. Engineering Applications of Computational Fluid Mechanics, 14(1), 1404-1415. https://doi.org/10.1080/19942060.2020.1835734.
[23] Salynskikh, V.M., Shcherbakova, E.E., Arefieva, L.P. (2018). Improving the mechanical properties of 65G steel springs by isothermal hardening. Young Researcher Don, 2(11), 77-80 (in Russian)