Optimization The High Speed Machining of Hardened AISI 4140 Steel Using Vapor Deposited Cutting Tools (Wear and Roughness)
Subject Areas : Mechanical EngineeringMehdi Jalali Azizpour 1 , Ata Fardaghaie 2
1 - Department of Mechanic, Ahvaz branch, Islamic Azad University, Ahvaz, Iran
2 - Department of Mechanics, Ahvaz branch
Islamic Azad University, Ahvaz, Iran
Keywords: HSM, PVD, Flank wear, CVD, Genetic Algorithm, Roughness, Tool wear,
Abstract :
In this study, the main cutting parameters of high speed machining (HSM) including cutting speed, feed rate, depth of cut as well as deposition method were optimized using genetic algorithm considering the average surface roughness (Ra) of work piece and flank wear (Vb) of CVD and PVD coated tool criteria in high speed turning of hardened AISI 4140 Steel. Standard L18 orthogonal array has been used for the design of experiment (DOE) applying Taguchi approach. Multiple linear regression model applying Minitab, was used to determine the relationship and interaction between machining parameters and outputs. For genetic algorithm(GA) optimization, the average was applied as a functional output of design of experiments. The results of GA for smaller- the better quality characterization shows the optimum roughness of 1.107 mm and optimum flank wear of 0.461mm. The confirmation tests were carried out in order to validate the response of predicted optimum condition. The results of validation test show a good agreement between obtained optimum condition and the results of genetic algorithm. The analysis of variance was used in order to obtain the contribution of each factor on the output statistically. ANOVA results indicated that the cutting speed and cut depth are the most effective factors on the flank wear by 37.02 and 27.80 percent contribution respectively. The most effective factors on surface roughness were feed rate and cutting speed by 82.49 and 10.50 percent contribution respectively. Stereoscopy and Scanning electron microscopy was used to evaluate the wear mechanism and topography of worn surface.
[1] Kivak, T., “Optimization of Surface Roughness and Flank Wear Using the Taguchi Method in Milling of Hadfield Steel with PVD and CVD Coated insertsˮ, Measurement, Vol. 50, 2014, pp. 19 – 28
[2] Bouzakis, K., Michailidis, N., Skordaris, G., Bouzakis, E., Biermann, D., and M’Saoubi, R., “Cutting with Coated Tools: Coating Technologies, Characterization Methods and Performance Optimizationˮ, CIRP Annals - Manufacturing Technology, Vol. 61, 2012, pp. 703 – 723
[3] Narasimha, M., Reiji Kumar, R., and Kassie, A., “Performance of Coated Carbide Toolsˮ, The International Journal of Engineering and Science (IJES), Vol. 6, 2013, pp. 47 – 54.
[4] Sgderberg, S., hogmark, S., “Wear Mechanisms and Tool Life of High Speed Steels Related to Microstructureˮ, Wear, Vol. 110, 1986, pp. 315 – 329.
[5] Philip Selvaraj, D., Chandramohan, P., and Mohanraj, M., “Optimization of Surface Roughness, Cutting Force and Tool Wear of Nitrogen Alloyed Duplex Stainless Steel in a Dry Turning Process Using Taguchi Methodˮ, Measurement, Vol. 49, 2014, pp. 205 – 215.
[6] Günay, M., Yücel, M., “Application of Taguchi Method for Determining Optimum Surface Roughness in Turning of High-Alloy White Cast Ironˮ, Measurement, Vol. 46, 2013, pp. 913 – 919.
[7] Shahrom, M. Yahya, N., and Yusoff, M., “Taguchi Method Approach on Effect of Lubrication Condition on Surface Roughness in Milling Operationˮ, Malaysian Technical Universities Conference on Engineering & Technology, Procedia Engineering, Vol. 53, 2013, pp. 594 – 599.
[8] Chinchanikar, S., Choudhury, S. K., “Investigations on Machinability Aspects of Hardened AISI 4340 Steel at Different Levels of Hardness Using Coated Carbide Toolsˮ, Int. Journal of Refractory Metals and Hard Materials, Vol. 38, 2013, pp. 124 – 133.
[9] Schulz, H., Dorr, J., Rass, I. J., Schulze, M., Leyendecker, T., and Erkens, G., “Performance of Oxide PVD-Coatings in Dry Cutting Operationsˮ, Surface and Coatings Technology, Vol. 146 –147, 2001, pp. 480 – 485.
[10] Ranjan Das, S., Dhupal, D., and Kumar, A., “Experimental Investigation into Machinability of Hardened AISI 4140 Steel Using TiN Coated Ceramic Toolˮ, Measurement, Vol. 62, 2015, pp. 108 – 126.
[11] Bazargan, A., Applied Linear Regression, Third ed. 2012, Shiraz University.
[12] Mitchell, M., “AnIntroduction to Genetic Algorithmsˮ, A Bradford Book The MIT Press Cambridge, London, England 5th printing, 1999.
[13] Ranjit, R., “A Primer On the Taguchi Methodˮ, Second ed. 1990, Society of Manufacturing Engineers.
[14] Jalali Azizpour, M., Mohammadi majd, H., “Wear Mechanisms in High Speed Steel Gear Cutting Toolsˮ, International Journal of Chemical, Materials and Metallurgical Engineering, Vol. 4, No. 9, 2010.