Thermal and Mechanical Properties of Hybrid Composite Strengthened by Carbon Fibers/Aramid Fibers

محورهای موضوعی : Applied Mechanics

F Basati ¹ (Department of Mechanical Engineering, Razi University, Kermanshah, Iran)
M.H Yas ² (Department of Mechanical Engineering, Razi University, Kermanshah, Iran)

تاریخ دریافت : 1402/03/13 تاریخ پذیرش : 1402/05/10 تاریخ انتشار : 1402/06/10

کلید واژه: carbon fibers, aramid fibers, Modal Analysis, Thermal properties, Laminate hybrid composite, Mechanical Properties, Mixture law,

چکیده مقاله :

This work deals with the thermal, mechanical and dynamic properties of hybrid composites reinforced with carbon fibers and aramid fibers, whose matrix is ​​epoxy resin. In this study a series of hybrid fiber composite are prepared with carbon and aramid fibers as reinforcement. Thermal properties are obtained by thermal gravimetric analysis (TGA), Thermo-mechanical analysis (TMA) and hot plate analysis. Also mechanical properties are obtained by tensile and modal analysis tests. The experimental results are compared with the similar theoretical ones. Besides the effect of stacking sequence and hybrid ratio (adding the number of layers of carbon fibers), on the thermal and mechanical properties are investigated. The results show that by increasing the hybrid ratio although the weight of the sample is more, the thermal conductivity of the carbon fibers used is higher than that of the aramid fibers and this increase in thermal conductivity causes the heat to be transferred to the sample much faster and the temperature of the glass increases with the increase of the hybrid ratio. Due to the high stiffness of carbon fibers, adding it to the composite causes, the tensile modulus of the samples increases. By combining carbon fibers with aramid fibers, the toughness of carbon fibers can be increased and at the same time the brittle property of carbon fibers is removed due to the malleability of aramid fibers. It is concluded that aramid fiber has an effective role in improving failure strain due to its high toughness and malleability, while carbon fiber is very fragile. The lowest tensile strength occurs at the hybrid ratio of 29% with a value of 677.66 MPa. which is very close to the theoretical critical hybrid ratio. The results also show when the carbon fibers and aramid fibers are on the outer and the middle layers of the beam respectively, the frequency has a larger value because the aramid fibers have a very high impact resistance.

منابع و مأخذ:

1. Sudarisman Davies I.J., Hamada H., 2007, Compressive failure of unidirectional hybrid fibre-reinforced epoxy composites containing carbon and silicon carbide fibres, Composite Part A 38(3):1070-10744.


2. Pandya K.S., Veerraju Ch., Naik N.K., 2011, Hybrid composites made of carbon and glass woven fabrics under quasi-static loading, Materials Design 32(7): 4094-4009.


3. Nordin H., Täljsten B., 2004, Testing of hybrid FRP composite beams in bending, Composite Part B Engineering 35(1): 27-33.


4. Kim S.J., Chang S.H., 2006, The relation between compressive strength of carbon/epoxy fabrics and micro-tow geometry with various bias angles, Composite Structures 75(1-4): 400407.


5. Tanner D., Dhingera A.K., Pigliacampi J.J., 1985, Aramid fiber composites for general engineering, The Journal of The Minerals, Metals & Materials Society 38: 21-25.


6. [6] Won M., Dharan C., 2002, Drilling of aramid and carbon fibre polymer composites, Manufacturing Science and Engineering (Transaction ASME 124: 778-783.


7. Lewin M., Preston J., 2007, Handbook of fiber science and technology, High Technology Fibers Part B Materials and Manufacturing Processes 6(4): 745-748.


8. Chang J., Niu H., Zhang M., Ge Q., Li Y., Wu D., 2015, Structures and properties of polyimide fibers containing ether units, Journal of Applied Polymer Sciences 132(34): 42474.


9. Chang J., Ge Q., Zhang M., Liu W., Cao L., Niu H., Sui ,Wu D., 2015, Effect of pre-imidization on the structures and properties of polyimide fibers, RSC Advances 85: 69555-69566.


10. Zhang M., Niu H., Wu D., 2018, Polyimide fibers with high strength and high modulus: preparation, structures, properties, and applications, Macromol Rapid Commun 39(20): 1800141.


11. Li S., Zhuo H., Han E., Zhang D., Liu G., Tian G., Bao J., Wu , 2020, Preparation and properties of high strength and high modulus polyimide fiber/modified cyanate resin composites, Acta Material Compos Sinica  37(1): 42-49.


12. He B., Wang B., Wang Z., Qi S., Tian G., Wu D., 2021, Mechanical properties of hybrid composites reinforced by carbon fiber and high strength and high-modulus polyimide fiber, Polymers 204(9): 122830.


13. Abdel Ghafaar M., Mazen A.A., El-Mahalla, N.A., 2006, Application of the rule of mixtures and Halpin-Tsai equations to woven fabric reinforced epoxy composites, Journal of Engineering Science 34(1): 227-236.


14. Nielsen L.E., 1974, The thermal and electrical conductivity of two phase systems, Industrial & Engineering Chemistry Fundamentals 13(1): 17-20.


15. Alfonso Lopez I., Figueroa A., Rodriguez V., Pozo L., 2016, Estimation of elastic moduli of particulate-reinforced composites using finite element and modified Halpin-Tsai models, Brazilian Society of Mechanical Science and Engineering 38: 1317-1324.


16. Halpin J.C., Kardos J.L., 1976, The halpin-tsai equations: a review, Polymer Engineering and Science 16(5): 344-352


17. Prasad V.V., Talupula S., 2018, A review on reinforcement of basalt and aramid (Kevlar 129) fibers, Materialstoday Proceedings 5(2): 5993-5998.


18. Song J.H., 2015, Pairing effect and tensile properties of laminated high-performance hybrid composites prepared using carbon/glass and carbon/aramid fibers, Composites Part B 79: 61-66.


19. Cheon J., Lee M., Kim M., 2020, Study on the stab resistance mechanism and performance of the carbon, glass and aramid fiber reinforced polymer and hybrid composites, Composite Structures 234(15): 111690.


20. Kim S., Lee J., Roh C., Eun J., Kang C., 2019, Evalulation of carbon fiber and p-aramid composite for industrial helmet using cross-ply for protecting human heads, Mechanics of Materials 139 (2): 103203.


21. Aydin M., Acar V., Cakir F., Gundogdu O., Akbulut H., Akbulut H., 2022, Comparative dynamic analysis of carbon, aramid and glass fiber reinforced interply and intraply hybrid composites, Composite Structures 291: 115595.


22. Li S., Zhuo H., Han E., Zhang D., Liu G., Tian G., 2020, Preparation and properties of high strength and high modulus polyimide fiber/modified cyanate resin composites, Acta Material Compos Sinica 37: 42-49.


23. Zhuo H., Li S., Han E., Zhang D., Liu G., Tian G., 2019, Mechanical properties and failure mechanism of high strength and high modulus polyimide fiber reinforced epoxy composites, Acta Material Compos Sinica 36: 2101-2109.


24. Enew M.A., Abd Elfattah M., Fouda S.R., Hawash S.A., 2021, Effect of aramid and carbon fibers with nano carbon particles on the mechanical properties of RPDM rubber thermal insulators for solid rocket motors applications, Polymer Testing 103: 107341.