Effect of Formaldehyde on Pulsed Electro-Plated Nickel-Alumina Nanocomposite Coatings
محورهای موضوعی : Journal of Environmental Friendly Materials
S Mirzamohammadi
1
(
Department of Materials and Metallurgical Engineering, Technical and Vocational
University (TVU), Tehran, Iran
)
M Velashjerdi
2
(
Department of Materials Science and Engineering, Faculty of Engineering, Arak University, Arak, Iran
)
A Anbarzadeh
3
(
Department of Mechanical Engineering, Technical and Vocational University (TVU), Tehran, Iran
)
کلید واژه:
چکیده مقاله :
Metal-based nanocomposite coating prepared by plating method can exhibit unique mechanical, chemical, and physical features which have led to their extensive application in various high-tech industries. Nickel-based nanocomposite coatings can pose far lower pollution toward the environment and related staff as compared with chromium-based ones. In this research, a novel compound was developed to coat nickel-alumina nanocomposite by adding formaldehyde to the plating bath. The concentration of alumina nanoparticles (NPs) in the plating bath was 10 g/L. The nickel-alumina nanocomposite coatings were prepared by a pulsed electrical current under ultrasound turbulence in the plating bath. Two Ni bathes in combination with Watt’s compound were used with and without formaldehyde addition. Before plating, the zeta potential of alumina NPs was measured in the two different baths. After plating, the cross-section of the coatings and the alumina content participated in the coating, as well as the coating morphology, were analyzed by scanning electron microscopy (SEM) equipped with energy-dispersive X-ray spectroscopy (EDX). Based on the results, incorporation of formaldehyde into the Watt’s solution increased the zeta potential of the nanoparticles from -4.1 to +30.5 mV; consequently, the nanoparticle content of the coatings enhanced from 4.6 to 8.5 vol.%.
[1] P. KumarRai and A. Gupta. Mater. Today. Proce., online (2021).
[2] D. G. Portela, T. C. d. M. Nepel, J. M. Costa and A. F. D. A. Neto, Mater. Sci. and Eng., B. 260, (2020), 114.
[3] C. Yan, N. Karthik and D. Xiong, Ceram. Int. 46, 10, Part A, (2020), 15714.
[4] S. R. Allahkaram, S. Golroh and M. MohammadAlipour. Mater. & Des. 32, 8–9, (2011), 4478.
[5] S. T. Aruna and G. Srinivas. Surf. Eng. 31, (2015), 708.
[6] M. M. Kamel, Q. Mohsen, Z. A. Hamid, S. M. Rashwan, I. S. Ibrahim and S. M. El–Sheikh. Int. J. Electron. Sci. 16, (2021), 1.
[7] Y. Chen, Y. Hao, W. Huang and Y. Ji, W. Yang. Surf. Coat. Tech., 310, (2017), 122.
[8] N. Elkhoshkhany, A. Hafnway and A. Khaled, J. Alloy. Comp. 695, (2017), 1505.
[9] H. K. Lee, H. Y. Lee and J. M. Jeon. Surf. Coati. Tech. 201, (2007), 4711.
[10] K. Zielińska, A. Stankiewicz and I. Szczygieł. J. Collo. Int. Sci. 377, (2012), 362.
[11] D. Lee, Y. X. Gan, X. Chen and J. W. Kysar, Mater. Sci. and Eng. A. 447, (2007), 209.
[12] J. A. Calderón, J. E. Henao and M. A. Gómez. Elect. Acta. 124, (2014), 190.
[13] S. Dehgahi, R. Amini and M. Alizadeh. 692, (2017), 622.
[14] S. Ghaziof and W. Gao, J. of Alloy. and Compo. 622, (2015), 918.
[15] Y. Wang, Y. Li and Z. Zhu, Mater. Sci. and Eng., A, 775, (2020), 138.
[16] H. K. Lee, H. Y. Lee and J. M. Jeon. Surf. and Coati. Tech., 201, (2007), 4711.
[17] H. Gül, F. Kılıç, M. Uysal, S. Aslan, A. Alp and H. Akbulut. Appli. Surf. Sci. 258, (2012), 4260.
[18] H. Gül, F. Kılıç, S. Aslan, A. Alp and H. Akbulut, Wear, 267, (2009), 976.
[19] L. Chen, L. Wang, Z. Zeng and T. Xu. Surf. and Coat. Tech., 201, (2006), 599.
[20] R. Sen, S. Bhattacharya, S. Das and K. Das, J. Alloy. and Compo., 489, (2010), 650.
[21] D. Thiemig and A. Bund, Appl. Surf. Sci., 255, (2009), 4164.
