Electrodeposition of cobalt oxide thin films for potential applications

Augustine, Sandra; Ekpunobi, Azubike; Jeroh, Diemiruaye

doi:10.57647/J.JTAP.2023.1702.25

کد مقاله : JTAP-2212-1138 (R1) بازدید : 83 صفحه: 0 - 0

10.57647/J.JTAP.2023.1702.25

نوع مقاله: پژوهشی

Electrodeposition of cobalt oxide thin films for potential applications

محورهای موضوعی : Journal of Theoretical and Applied Physics

Sandra Augustine ¹ (Department of Physics and Industrial Physics, Nnamdi Azikiwe University, Awka, Nigeria.)
Azubike Ekpunobi ² (Department of Physics and Industrial Physics, Nnamdi Azikiwe University, Awka, Nigeria.)
Diemiruaye Jeroh ³ (Department of Physics and Industrial Physics, Nnamdi Azikiwe University, Awka, Nigeria.)

تاریخ دریافت : 1401/10/09 تاریخ پذیرش : 1401/12/09 تاریخ انتشار : 1402/02/11

کلید واژه: crystalline, band widening, cobalt oxide, blue-shift, molar concentrations,

چکیده مقاله :

Cobalt oxide thin films at varied molar concentrations were prepared by electrodeposition technique. Ultraviolet-Visible (UV/VIS) analysis conducted on the grown films revealed blue shift in the absorption edge at increased molar concentrations, which is a consequence of band gap widening. The band gap values (3.65 eV to 3.85 eV) in this research are greater than the value (2.4 eV) for the bulk phase of cobalt oxide. This increase in band gap can be likened to higher concentration effect and quantum-size phenomenon. Scanning Electron Microscopy (SEM) analysis indicated a porous nature for the material, suggesting its ability in absorbing ultraviolet (UV) radiation, thus confirming its use as an absorber material for solar cells fabrication. Energy Dispersive X-ray (EDX) study confirmed the growth of cobalt oxide. X-ray diffraction (XRD) analysis confirms the crystalline nature of the films with grain sizes within the range of 0.7 nm to 1 nm for varied molar concentrations. Electrical studies reveal a linear relationship of resistivity values with molar concentrations, while the conductivity values reveal inverse relationship with molar concentration.

چکیده انگلیسی:

منابع و مأخذ:

متن کامل:

Electrodeposition of Cobalt Oxide Thin Films for Potential Applications

1Sandra, A., 2Ekpunobi, A.J. and 3*Jeroh D.M.

1-3Department of Physics and Industrial Physics, Nnamdi Azikiwe University, Awka-Nigeria.

*Author of correspondence: dm.jeroh@unizik.edu.ng

Abstract

Keywords: molar concentrations, cobalt oxide, band widening, blue-shift, crystalline.

Article Highlights

v High absorbance recorded around the ultraviolet (UV) region.

v X-ray diffraction revealed the cobalt oxide films are crystalline.

v The porous nature of the films suggests a good ability to absorb UV radiation.

MSC Classification: 14-XX, 74-XX

JEL Code: Q4

1.0 Introduction

Semiconductor thin film research has continued to be an area of intense interest. This possibly stems from the fact that devices based on semiconductors have proven effective in diverse areas like solar cells (SCs) fabrication, fabricating electronic devices, fibre-optics technology, etc (Jeroh et al., 2022). One essence of studying semiconductor films is to understand their various underlying properties and suggest applications based on these properties.

Cobalt oxide fall within the materials classified as transition metal oxides (TMOs) or transparent conducting oxides (TCOs). Due to their very good optical, electronic, catalytic and magnetic properties, TMOs are considered as promising materials for variety of technological applications (Hassan and Maki, 2017). These properties have triggered their use in optoelectronic devices such as electrochromic sensors and photovoltaic devices (Lakehal et al., 2018). Cobalt oxide exhibit p-type conductivity and ferromagnetic behaviour.

Cobalt oxide, due to its power storage capacity, finds applications in supercapacitors and selective absorbers in solar cells. Cobalt oxides, due to their importance, also have applications in the manufacture of sensors, optoelectronics and other electrical devices (Nikzad et al., 2010). Cobalt oxide has been synthesized hydrothermally (Moridon et al., 2021), by sol-get coating (Rahman et al., 2017), by electrochemical deposition (Kelpsaite et al., 2011; Berauskiene and Valatka 2018; Mirzaeian et al., 2020) and pyrolysis (Zahan and Podder, 2019).

In this research, novel cobalt oxide is prepared by electrodeposition at different molar concentrations. Increased molar concentration has shown to improve the crystalinity of the films (Hassan and Maki, 2017). Electrodeposition technique was preferred in this research when compared to other growth techniques of semiconductors due to its low cost. Electrodeposition has the advantage of scalability, simplicity and manufacturability (Dharmadasa and Haigh, 2006). Electrodeposition also offers the ability to control the composition of the chemical and film thickness by variation of either current or potential (Urazov, et al., 2022). After deposition, the optical, electrical, and structural properties of the material were examined for possible applications of the material.

1.1 Materials and method

1.1.1 Materials

The starting chemicals and solvents include cobalt (II) chloride (CoCl2.6H2O), potassium hydroxide (KOH), ammonia solution (NH3) and de-ionized water. Tin oxide substrates doped with fluorine (FTO) were employed for the deposition.

Power source

The power supply used in this work was a regulated power supply capable of converting AC voltage into DC voltage. The 220 AC voltage from the main was converted into 120 DC voltage using AC – DC converter. During connection, the positive terminal (live) of the output from the power supply was red while the negative (neutral) of the output from the power supply was black. The working electrode (FTO glass) was connected to the negative terminal (cathode) while the carbon electrode was connected to the positive terminal (anode) during the deposition. The pictorial representation of the experimental setup is displayed in figure 1.

Fig. 1. Pictorial representation of an electrodeposition setup

1.1.2 Method

Electrodeposition setup comprising two-electrode cell was employed for the film’s growth. The electrochemical bath comprised a cation source (CoCl2.6H2O for Co2+), an anion source (KOH for OH2-) and deionized water in a 100 ml beaker. The reaction bath was continuously stirred with a magnetic stirrer hot plate, while a DC voltage power source was applied as the source of electric field. In the setup, a conducting glass (FTO) served as cathode while carbon served as anode. With the setup in place, the concentration of the cation was varied at 0.01 mol, 0.02 mol, 0.03 mol, 0.04 mol, and 0.05 mol respectively while other growth parameters were kept constant.

The reaction equation is given as:

Details of the experimental procedure can be further explained using table 1.

Table 1. VARIATION OF CONCENTRATION

Slide No	CoCl2.6H2O (ml)	KOH (ml)	NH3 (ml)	Conc. (mol)	Time (Sec.)	Voltage (v)
A1	25	10	5	0.01	8	5
A2	25	10	5	0.02	8	5
A3	25	10	5	0.03	8	5
A4	25	10	5	0.04	8	5
A5	25	10	5	0.05	8	5

Where A1, A2, A3, A4 and A5 are all Fluorine doped tine oxide substrate that was used for the deposition. In concentration variation, 25ml of CoCl2.6H2O, 10ml of KOH and 5ml of NH3 were measured into 100ml beaker, concentration was varied at the range of 0.01mol, 0.02mol, 0.03mol, 0.04mol and 0.05mol respectively at constant time 8sec. and constant voltage 5v.

1.1.3 Characterization of the films

Optical characterization was performed by a UV/1800 Visible Spectrophotometer, structural studies (x-ray diffraction) was obtained using a Bruker-D8 Advance X-ray diffractometer with Cu-Kα line (λ = 1.54056 Å) in 2θ scanning range from 10° - 70°, electrical characterization was performed using four point probe (Model T345) while Scanning Electron Microscopy (SEM) and Energy Dispersive Analysis (EDX) were used to obtain the surface morphology and compositions of the films respectively.

1.2 Results and discussions

1.2.1 Optical characterization

The absorptions at different molar concentrations of the cations are presented in figure 2. Optical range covered is 200 nm to 800 nm.

$C:\Users\Dr. E.J. Jeroh\Desktop\Sandra Files\Aborbance New Mol.jpg$

Fig. 2. Absorption spectra of cobalt oxide prepared at different molar concentrations.

The absorption spectra decreased steadily as they progressed from the ultraviolet (UV) region to the visible region, indicating band to band transition of the cobalt oxide films. Increased molar concentration from 0.01 to 0.04 M shows a closely packed spectrum within the UV region. From SEM analysis, these closed-packed spectrum is porous (contains pores). These pores on the film’s surface aid in trapping the UV light, hence can store the UV radiation in the material. Such ability indicates that cobalt oxide cell can act as a good storage material for photovoltaics. A further increment in molar concentration to 0.05 mol resulted in a band edge shift from higher wavelength to lower wavelength (blue shift). The observed blue shift for the band edge is a consequence of widened band gap and higher concentration effect.

Figure 3 displays the band gap energies for varied concentrations of cobalt.

$C:\Users\Dr. E.J. Jeroh\Desktop\Sandra Files\Band Gap new Mol.jpg$

Fig. 3. Band gap energies for different molar concentrations of cobalt

Tauc’s plot was used to obtain the band gap values at different molar concentrations (figure 3). The band gap values (3.65 eV to 3.85 eV) in this research are greater than the value (2.4 eV) for the bulk phase of CoO. This increase in band gap can be likened to higher concentration effect and quantum-size phenomenon. The quantum-size phenomenon results in a blue-shift and subsequently shifts the band gap to higher energies (Jeroh et al., 2020). For semiconductor particles in the nano-range, an increase in band gap results in a blue-shift (Dhas et al., 2015). Depending on the molarity concentration, the highest band gap was obtained at 0.05 M. The results obtained in this research find perfect agreement with previous reports of (Dhas et al., 2015; Farhadi et al., 2016).

1.2.2 Structural characterization

Fig. 4. XRD spectra for all varied concentrations of cobalt

The XRD spectra for all varied concentrations are displayed in figure 4. The observed XRD patterns for all concentrations appear identical; as such, no additional peaks are evident, indicating the non-existence of any impurity phase. Thus, at higher concentrations, the results show that the overall crystalline structure of the studied films remains unchanged. From figure 3, well-defined peaks are evident, suggesting the crystalline nature of the films. The observed peaks are positioned at 2θ values of and corresponding to crystal planes of [111], [200], [222], [300] and [311] which are consistent with the cubic structure. The [111] plane appears to be the preferred growth plane. This result agrees with previous reports (Farhadi et al., 2016; Prieto et al., 2019; Helen and Joseph, 2017; Zohra et al., 2014; Onah et al., 2013).

The crystallite sizes (in nm) in this research were calculated from Debye-Scherrer’s equation (Jogade et al., 2015) using the expression:

The films have crystallite sizes within the range of 0.7 nm to 1 nm for different molar concentrations of cobalt.

The dislocation density was between 3.09 m2 to 6.45 m2.

Fig. 5a. SEM image of CoO deposited at 0.01 mol

$C:\Users\User\Desktop\Sandra M.Sc work\SEM RESULTS\2_ (4).tif$

Fig. 5b. SEM image of CoO deposited at 0.02 mol

$C:\Users\User\Desktop\Sandra M.Sc work\SEM RESULTS\4_ (6).tif$

Fig. 5c. SEM image of CoO deposited at 0.03 mol

$C:\Users\User\Desktop\Sandra M.Sc work\SEM RESULTS\4_ (7).tif$

Fig. 5d. SEM image of CoO deposited at 0.04 mol

$C:\Users\User\Desktop\Sandra M.Sc work\SEM RESULTS\4_ (9).tif$

Fig. 5e. SEM image of CoO deposited at 0.05 mol

The SEM images of the films are displayed in figure 5(a-e). The crystallites are spread across the surface of the films. From figure 5b, the SEM image of the film obtained at 0.02 mol appears porous. However, at increased molarity (0.03 mol, 0.04 mol, 0.05 mol), the porosity of the material appears reduced as the films were observed to be more compacted resulting in lower particle sizes distributed on the surface of the films. Similar CoO with porous morphology has been reported (Amin-Chalhoub et al., 2016). The porous nature provides the films with the advantage of absorbing UV light, which is a very good requirement for absorber materials for solar cells fabrication.

The elemental composition of the grown CoO films obtained by EDX analysis is displayed in figures 6a and 6b.

$C:\Users\User\Desktop\Sandra M.Sc work\SEM RESULTS\2%_1.png$

Fig. 6a. EDX spectrum of CoO deposited at 0.02 mol.

$C:\Users\User\Desktop\Sandra M.Sc work\SEM RESULTS\6V_1.png$

Fig. 6b. EDX spectrum of CoO deposited at 0.05 mol.

The EDX spectrum for the films shows peaks corresponding to cobalt and oxygen respectively confirming the growth of CoO.

1.2.3 Electrical Studies

The electrical characterizations were measured using four-point probe (Model T345). The plot of the values of resistivity versus film thickness is presented in figure 7.

$C:\Users\Dr. E.J. Jeroh\Desktop\Sandra Files\Resistivity.jpg$

Fig. 7. Electrical resistivity versus thickness of CoO for different molar concentrations

The electrical properties of CoO thin films revealed that the material deposited at different molar concentrations of 0.01 mol, 0.02 mol, 0.03 mol, 0.04 mol and, 0.05 mol had thickness increment from 108.86 – 117.73 nm with a corresponding increase in the resistivity of the deposited material from 5.121 x 10-11 - 7.127 x 10-11 (Ω.cm) which resulted in a decrease of the electrical conductivities of the deposited material from 1.952 x 1010 - 1.403 x 1010 (Ω.cm)-1 (Table 2). The increased resistivity stems from reduction in the mean free path of the conduction electrons arising from increase in scattering effect (Lacy, 2011). Conduction electrons (CEs) are responsible for the conductivity of any material. If the CEs are free to move within the lattice, conductivity becomes easier, if not mobile, conductivity is unlikely. In every material, the CEs are attached to the atoms in the form of covalent bonding. However, once the electrons gain enough energy, they easily break the covalent bond and are free to move within the lattice. The movement of these free electrons result in the material’s conductivity. Therefore, the implication of high resistivity at increased molar concentration is that the material’s conductivity is reduced because this high resistivity prevents the electrons from easily breaking up the covalent bond, thus slowing down conductivity.

Table 2. Resistivity, conductivity and thickness values for CoO

1.3 Conclusion

Cobalt oxide films were deposited on FTO glass substrates at different molar concentrations by electrodeposition. The characterized films were studied for their optical, morphological, structural and electrical properties. The optical and morphological results indicate closely packed spectrum having pores on the surface of the material. These pores are capable of trapping UV radiation, thus suggesting the material’s usefulness as an absorber for solar cell fabrication. Structural (XRD) studies suggest the grown films are crystalline, belonging to the cubic crystal structure. The crystallite sizes were calculated from Debye-Scherrer’s equation and found to have values between 0.7 nm and 1 nm for different molar concentrations of cobalt. The electrical studies reveal increase in resistivity and decrease in conductivity as thickness and molarity increases. The increased resistivity in response to increased thickness and increased molar concentration were observed to have occurred due to the reduction in the mean free path of the CEs of cobalt oxide. Hence, cobalt oxide will function better as a conductive material at lower molar concentration.

Statement and Declaration

Ethics

All ethical standards have been complied with.

Conflict of Interests

The corresponding author, on behalf of all authors declare that there are no conflicts of interests arising from this research.

Research Data Availability

The data used for the entire research is available upon request.

References

[1] Amin-Chalhoub, E., Duguet, T., Samelor, D., Debieu, O., Ungureanu, E. and Vahlas, C. (2016). Constantin chemical vapour deposition of low reflective cobalt (II) oxide films. Appl. Surf. Sci. 360: 540 – 546. DOI: 10.1016/j.apsusc.2015.10.188

[2] Berauskiene, I. and Valatka, E. (2018). Electrocatalytic and pseudocapacitive properties of cobalt (hydro) oxide films on sintered metal fiber filter. Mater. Renew. Sustain. Energy, 7: 1 – 10. https://doi.org/10.1007/s40243-017-0108-2

[3] Dharmadasa, I.M., Haigh, J. (2006). Strengths and Advantages of Electrodeposition as a Semiconductor Growth Technique for Applications in Macroelectronic Devices. J. Electrochem. Soc., 153: G47-G52.

[4] Dhas, C.R., Venkatesh, R., Jothivenkatachalam, K., Nithya, A., Benjamin, B.S., Raj, A.M.E., Jeyadheepen, K., Sanjeeviraja, C. (2015). Visible light driven photocatalytic degradation of Rhodamine B and Direct Red using cobalt oxide nanoparticles. Cer. Int., 41: 9301-9313 doi: https://dx.doi.org/10.1016/j.ceramint.2015.03.238

[5] Farhadi, S., Javanmard, M., Nadri, G. (2016). Characterization of cobalt oxide nanoparticles prepared by the thermal decomposition of [Co(NH3)5(H2O)](NO3)3 complex and study of their photocatalytic activity. Acta Chim. Slov., 63, 335-343 doi: 10.17344/acsi.2016.2305

[6] Hassan, A.I., Maki, S.I. (2017). Structural and optical properties of copper- doped cobalt Oxide thin films prepared by spray pyrolysis. Int. J. Eng. Sci. Res. Technol., 6: 527-535.

[7] Helen V., Joseph P. J (2017). Influence of annealing on the structural, optical and magnetic properties of CoO thin films. J. Mater. Res. Innov. 23: 200-206 https://doi.org/10.1080/14328917.2017.1414110

[8] Jeroh, D.M., Ekpunobi, A.J., Okoli, D.N. (2020). The optical properties of europium-doped zinc selenide films. Journal of Nano- and Electronic Physics. 12: 05006-1 – 05006-5 doi:10.21272/jnep.12(5).05006

[9] Jeroh D.M., Ekpunobi A.J., Okoli D.N. (2022). Optical and structural characterization of CdSe:Eu at different volumes of europium concentration. Journal of Theoretical and Applied Physics. 16: 1-5. http://dx.doi.org/10.30495

[10] Jogade, S.M., Sutrave, D.S. and Gothe, S.D. (2015). Electrochemical analysis of cobalt oxide thin film for supercapacitor. Int. J. Adv. Res. Phys. Sci. 2: 36 – 41.

[11] Kelpsaite, L., Baltrusaitis, J. and Valatka (2011). Electrochemical deposition of porous cobalt oxide films on AlSl 304 type steel. Mater. Sci. 17: 236 – 243. http://dx.doi.org/10.5755/j01.ms.17.3.586

[12] Lakehal, A., Bedhiaf, B., Bouaza, A., Benhebal, H., Ammari, A., Dalache, C. (2018). Structural, optical and electrical properties of Ni-doped Co3O4 prepared via sol-gel technique. Mater. Res. 21: 1-8.

DOI: http://dx.doi.org/10.1590/1980-5373-MR-2017-0545

[13] Mirzaeian, M., Akhanova, N., Gabdullin, M., Kalkozova, Z., Tulegenova, A., Nurbolat, S. and Abdullin K. (2020). Improvement of the pseudocapacitive performance of cobalt oxide-based electrodes for electrochemical capacitors. Energies, 13: 1 – 16. doi:103390/en13195228.

[14] Moridon, S.N.F., Salehmin, M.N.I., Arifin, K., Minggu, L.F., Kassim, M.B. (2021). Synthesis of cobalt oxide on FTO hydrothermal method for photoelectrochemical water splitting application. Appl. Sci. 11: 3031 (1-13) https://doi.org/10.3390/app11073031

[15] Nikzad L, Vaezi M.R., Alibeigi S. (2010). Preparation of cobalt oxide/zinc oxide nanocomposite. IJE Transactions B: Applications. 23: 133 - 137.

[16] Onah D.U, Okeke C. E, Osuji R. U, Ezekoye B. A, Ekpe J. E, Ibeh G. F, Ekwealor A. B. C and Ezema F. I. (2013). Study of the effects of thermal annealing on the optical band gap of nanocrystalline CoO thin films prepared by chemical bath deposition. Chem. Mater. Res. 3: 43-51.

[17] Prieto P, Marco J. F, Serrano A, Manso M, de la Figuera J. (2019). Highly oriented (111) CoO and Co3O4 thin films grown by ion beam sputtering. J. Alloy. Compd. 810, 151912. https://doi.org/10.1016/j.jallcom.2019.151912.

[18] Rahman, M. M., Miran, H. A., Jiang, Z. T., Altarawneh, M., Chuah, L. S., Lee, H. L., Amri, A., Mondinos, N., Dlugogorski, B. Z. (2017). Investigation of the post-annealing electromagnetic response of Cu-Co oxide coatings via optical measurement and computational modelling. RSC Adv. 7: 16826-16835.

https://doi.org/10.1039/c6ra25626k

[19] Urazov, K.A., Yaskevich, V.I., Myrzabekov, B.E. (2022). Electrochemical deposition of Cu2ZnSnSe4 thin films on Mo-glass electrode from tartaric acid. Int. J. Electrochem. Sci., 17: 1-8. doi: 10.20964/2022.08.03

[20] Zahan, M., Podder, J. (2019). Surface morphology, optical properties and Urbach tail of spray deposited Co3O4 thin films. J. Mater. Sci.: Mater. Electron. 30:4259–4269 doi:10.1007/s10854-019-00717-2

[21] Zohra N. K, Saliha A, Saira R, Rehana Z and Shahzad N. (2014). Structural characterization and optical

properties of cobalt oxide thin films.

http://www.i-asem.org/publication_conf/acem14/7.SMM/T4C.2.MS526_719F-2.pdf. Accessed 24

December, 2021.

Samples	Thickness, t (nm)	Resistivity, (Ω.cm)	Conductivity, (Ω.cm)-1
0.01 mol	108.86	5.121 x 10-11	1.952 x 1010
0.02 mol	110.93	5.242 x 10-11	1.907 x 1010
0.03 mol	111.72	6.412 x 10-11	1.559 x 1010
0.04 mol	113.06	6.512 x 10-11	1.535 x 1010
0.05 mol	117.73	7.127 x 10-11	1.403 x 1010

اشتراک گذاری

آدرس مقاله

Electrodeposition of cobalt oxide thin films for potential applications

سکوی نشر دانش

پیوندهای سایت

مراکز مرتبط

پشتیبانی

صفحات رسمی