Comparative study of thermal performance of plain and filleted plate-fin heatsinks under the simultaneous influence of impinging air jet and internal water flow
محورهای موضوعی : Thermodynamics and Heat TransterShervin Azadi 1 , Ali Abjadi 2
1 - Department of Mechanical Engineering, South Tehran Branch, Islamic Azad University, Tehran, Iran
2 - Department of Mechanical Engineering, South Tehran Branch, Islamic Azad University, Tehran, Iran
کلید واژه: Heat Sink, Fin, Microchannel, Numerical Solution, Hybrid Mesh,
چکیده مقاله :
In this paper, the thermal performance of two types of heat sinks one with simple plate fins and the other with pin fins including fillet is numerically investigated under the simultaneous influence of a top impinging air jet and the flow of pure water through the internal microchannels of the microchannel heat sink. The objective is to evaluate the effect of fin geometry on the heat transfer rate, pressure drop, Nusselt number, and the outlet temperature of the cooling fluid. In addition, the effect of Reynolds number on the thermal and hydraulic performance of these heatsinks under conditions of simultaneous water flow in internal microchannels and impinging air jets was also investigated. The continuity, momentum, and energy equations for steady, laminar, and incompressible flow are solved, and the numerical analysis is carried out using a composite mesh. The results indicate that pin fins exhibit better thermal performance at high flow rates, whereas plate fins are more suitable at lower flow rates due to their lower pressure drop.
This study can serve as a basis for geometric optimization in the design of hybrid thermal management systems.
In this paper, the thermal performance of two types of heat sinks one with simple plate fins and the other with pin fins including fillet is numerically investigated under the simultaneous influence of a top impinging air jet and the flow of pure water through the internal microchannels of the microchannel heat sink. The objective is to evaluate the effect of fin geometry on the heat transfer rate, pressure drop, Nusselt number, and the outlet temperature of the cooling fluid. In addition, the effect of Reynolds number on the thermal and hydraulic performance of these heatsinks under conditions of simultaneous water flow in internal microchannels and impinging air jets was also investigated. The continuity, momentum, and energy equations for steady, laminar, and incompressible flow are solved, and the numerical analysis is carried out using a composite mesh. The results indicate that pin fins exhibit better thermal performance at high flow rates, whereas plate fins are more suitable at lower flow rates due to their lower pressure drop.
This study can serve as a basis for geometric optimization in the design of hybrid thermal management systems.
[1] Shams Taleghani, A., and Torabi, F., Recent developments in aerodynamics, Frontiers in Mechanical Engineering, 10, p.1537383, 2025.
[2] Shams Taleghani, A., and Ghajar, A., Aerodynamic characteristics of a delta wing aircraft under ground effect, Frontiers in Mechanical Engineering, vol. 10, p. 1355711, 2024.
[3] Shams Taleghani, A., Hesabi, A., Esfahanian, V., Numerical study of flow control to increase vertical tail effectiveness of an aircraft by tangential blowing, International Journal of Aeronautical and Space Sciences, pp. 1-15, 2024.
[4] Abdolahipour, S., Review on flow separation control: effects of excitation frequency and momentum coefficient, Frontiers in Mechanical Engineering, vol. 10, p. 1380675, 2024.
[5] Shams Taleghani, A., Shadaram, A., Mirzaei, M., Effects of duty cycles of the plasma actuators on improvement of pressure distribution above a NLF0414 airfoil, IEEE Transactions on Plasma Science, vol. 40, no. 5, pp. 1434-1440, 2012.
[6] Abdolahipour, S., Effects of low and high frequency actuation on aerodynamic performance of a supercritical airfoil, Frontiers in Mechanical Engineering, vol. 9, p. 1290074, 2023.
[7] Shams Taleghani, A., Shadaram, A., Mirzaei, M., Abdolahipour, S., Parametric study of a plasma actuator at unsteady actuation by measurements of the induced flow velocity for flow control, Journal of the Brazilian Society of Mechanical Sciences and Engineering, vol. 40, pp. 1-13, 2018.
[8] Mirzaei, M., Taleghani, A. S., and Shadaram, A., Experimental study of vortex shedding control using plasma actuator, Applied Mechanics and Materials, vol. 186, pp. 75-86, 2012.
[9] Azadi, S., Abjadi, A., Vahdat Azad, A., Ahmadi Danesh Ashtiani, H., and Afshar, H., Enhancement of heat transfer in heat sink under the effect of a magnetic field and an impingement jet, Frontiers in Mechanical Engineering, vol. 9, p. 1266729, 2023.
[10] Azadi, S., Abjadi, A., Vahdat Azad, A., Ahmadi Danesh Ashtiani, H., and Afshar, H., Experimental investigation of enhancement heat dissipation in a novel heat sink under simultaneous impact of impingement jet and magnetic field, Frontiers in Mechanical Engineering, vol. 10, p. 1450972, 2024.
[11] Sun, X.Y., Dai, Y.J., Ge, T.S., Zhao, Y., and Wang, R.Z., Comparison of performance characteristics of desiccant coated air-water heat exchanger with conventional air-water heat exchanger–Experimental and analytical investigation, Energy, vol. 137, pp. 399-411, 2017.
[12] Aghaei, S., and Khaleghi, H., Development of a mathematical correlation for polydisperse non-spherical drug particle deposition in the human upper respiratory system, International Journal of Biomedical Engineering and Technology, vol. 43, no. 1, pp. 13-37, 2023.
[13] Nair, V., Baby, A., Anoop, M., Indrajith, S., Murali, M., and Nair, M. B., A comprehensive review of air-cooled heat sinks for thermal management of electronic devices, International Communications in Heat and Mass Transfer, vol. 159, p. 108055, 2024.
[14] Fan, Y., et al., Heat transfer performance study of fluid rotating microchannel heat sink, Case Studies in Thermal Engineering, vol. 58, p. 104390, 2024.
[15] Farooq, M., Zahid, I., Javaid, M.Y., Akbar, N.S., Bandarra Filho, E.P., Shahzad, M.F., Khan, M.I., Khan, M.I., Rehan, M. and Riaz, F., Experimental case study for optimizing heat sink performance using ZnO nanocarriers integrated with phase change materials for environmental sustainability, Case Studies in Thermal Engineering, 66, p.105770, 2025.
[16] Li, X., Li, L., Hang, W., Wang, W., Yin, M., Wang, X., Bei, S., Xu, Q., Liu, J. and Zheng, K., Systematic investigation of hybrid cold plate combining embedded phase change material with liquid cooling minichannels under different ambient temperatures for battery thermal management, Journal of Energy Storage, vol. 108, p. 115125, 2025.
[17] Han, C., Ma, X., and Xu, J., Innovative configurations for heat sink integrated with piezoelectric fans, International Journal of Thermal Sciences, vol. 207, p. 109383, 2025.
[18] Pandey, V. and Lee, P. S., Maximizing liquid-cooled heat sink efficiency with advanced topology-optimized fin designs, International Journal of Heat and Mass Transfer, vol. 229, p. 125746, 2024.
[19] Huang, Y., Sarma, B., and Weibel, J. A., A predictive model for fin array boiling heat transfer performance under two-phase immersion cooling, International Journal of Heat and Mass Transfer, vol. 239, p. 126513, 2025.
