Controlling the Basal Texture for Significant Improvements in Mechanical Properties of AZ91D Mg Sheets Using Elevated-Temperature Constrained Groove Pressing
محورهای موضوعی : Mechanical EngineeringSadegh Ghorbanhosseini 1 , Faramarz Fereshteh Saniee 2 , Ali Sonboli 3
1 - Mechanical Engineering Department, Faculty of Engineering, Bu-Ali Sina University, Hamedan, Iran
2 - Mechanical Engineering Department, Faculty of Engineering, Bu-Ali Sina University, Hamedan, Iran
3 - Materials Engineering and Metallurgy, Arak University, Arak, Iran
کلید واژه: AZ91D Magnesium alloy, Constrained Groove Pressing, Microstructure, Texture, Mechanical properties.,
چکیده مقاله :
A severe plastic deformation (SPD) technique, namely constrained groove pressing (CGP), is employed to investigate its influence on the texture and mechanical properties of AZ91D magnesium sheets. Three cycles of CGP were conducted on the AZ91D annealed sheets. Optical and scanning electron microscopy and X-ray diffraction (XRD) revealed that initially β-Mg17Al12 particles existed in the annealed sample. The grain structure of the workpiece was also refined from 18 µm to 14 µm after a single pass at 300 ˚C. There was a strong basal texture for the annealed sheet with maximum intensity of 3.4 multiple random distribution (MRD). After the first CGP cycle, the basal texture of the annealed sample was controlled and the maximum intensity of the basal texture did not significantly change. The inverse pole figures for various specimens demonstrated that the main texture was [0 0 0 1]║TD with increasing intensity during the next passes. It was found by measuring the hardness that 3-passed sample had the lowest homogeneity with a maximum inhomogeneity factor of 5.69. The yield strength and elongation of the annealed sheet were respectively increased to 166.7 MPa and 36.1%, showing about 29% and 47% enhancements, by performing just the first pass of the CGP operation.
A severe plastic deformation (SPD) technique, namely constrained groove pressing (CGP), is employed to investigate its influence on the texture and mechanical properties of AZ91D magnesium sheets. Three cycles of CGP were conducted on the AZ91D annealed sheets. Optical and scanning electron microscopy and X-ray diffraction (XRD) revealed that initially β-Mg17Al12 particles existed in the annealed sample. The grain structure of the workpiece was also refined from 18 µm to 14 µm after a single pass at 300 ˚C. There was a strong basal texture for the annealed sheet with maximum intensity of 3.4 multiple random distribution (MRD). After the first CGP cycle, the basal texture of the annealed sample was controlled and the maximum intensity of the basal texture did not significantly change. The inverse pole figures for various specimens demonstrated that the main texture was [0 0 0 1]║TD with increasing intensity during the next passes. It was found by measuring the hardness that 3-passed sample had the lowest homogeneity with a maximum inhomogeneity factor of 5.69. The yield strength and elongation of the annealed sheet were respectively increased to 166.7 MPa and 36.1%, showing about 29% and 47% enhancements, by performing just the first pass of the CGP operation.
[1] Kojima Y. Handbook advanced Mg technology. Tokyo: Kallos Publishing Co.;
2000.
[2] Ferdowsi, M.R.G., Mazinani, M. and Ebrahimi, G.R., 2014. Effects of hot rolling and inter-stage annealing on the microstructure and texture evolution in a partially homogenized AZ91 magnesium alloy. Materials Science and Engineering: A, 606, pp.214-227.
[3] Azzeddine, H., Abdessameud, S., Alili, B., Boumerzoug, Z. and Bradai, D., 2011. Effect of grain boundary misorientation on discontinuous precipitation in an AZ91 alloy. Bulletin of Materials Science, 34(7), pp.1471-1476.
[4] Huang, X., Suzuki, K., Chino, Y. and Mabuchi, M., 2015. Texture and stretch formability of AZ61 and AM60 magnesium alloy sheets processed by high-temperature rolling. Journal of Alloys and Compounds, 632, pp.94-102.
[5] Guo, L. and Fujita, F., 2015. Influence of rolling parameters on dynamically recrystallized microstructures in AZ31 magnesium alloy sheets. Journal of Magnesium and Alloys, 3(2), pp.95-105.
[6] Ebrahimi, G.R., Maldar, A.R., Ebrahimi, R. and Davoodi, A., 2010. The effect of homogenization on microstructure and hot ductility behaviour of AZ91 magnesium alloy. Kovove Mater, 48, pp.277-284.
[7] Valiev, RZ., Korznikov, AV., Mulyukov, RR. 1993. Structure and Properties of Ultrafine-grained Materials Produced by Severe Plastic Deformation. Materials Science and Engineering A 168(2):141–148.
[8] Rosochowski, A. 2005. Processing Metals by Severe Plastic Deformation. Solid State Phenomena 101–102:13–22.
[9] Shin, D.H., Park, J.J., Kim, Y.S., Park, K.T. 2002. Constrained groove pressing and its application to grain refinement of aluminum. Materials Science and Engineering A328. 98–103.
[10] Lee, J.W., Park, J.J. 2002. Numerical and experimental investigations of constrained groove pressing and rolling for grain refinement. Journal of Materials Processing Technology 130–131. 208–213.
[11] Rafizadeh, E., A. Mani, and M. Kazeminezhad. 2009. The effects of intermediate and post-annealing phenomena on the mechanical properties and microstructure of constrained groove pressed copper sheet. Materials Science and Engineering: A. 515(1-2): p. 162-168.
[12] Satheesh Kumar, S.S., Raghu, T. 2013. Mechanical behaviour and microstructural evolution of constrained groove pressed nickel sheets. Journal of Materials Processing Technology 213. 214–220.
[13] Fong, K.S., Tan, M.J., Chua, B.W., Atsushi, D. 2015. Enabling wider use of Magnesium Alloys for lightweight applications by improving the formability by Groove Pressing. Procedia CIRP 26. 449 – 454.
[14] Hajizadeh, K., Ejtemaei, S. and Eghbali, B., 2017. Microstructure, hardness homogeneity, and tensile properties of 1050 aluminum processed by constrained groove pressing. Applied Physics A, 123(8), p.504.
[15] Lin, P., Tang, T., Zhao, Z., Wang, W. and Chi, C., 2017. Refinement Strengthening of AZ31 Magnesium Alloy by Warm Constrained Groove Pressing. Materials Science, 23(1), pp.84-88.
[16] Pouraliakbar, H., Jandaghi, M.R. and Khalaj, G., 2017. Constrained groove pressing and subsequent annealing of Al-Mn-Si alloy: microstructure evolutions, crystallographic transformations, mechanical properties, electrical conductivity and corrosion resistance. Materials & Design, 124, pp.34-46.
[17] Moradpour, M., Khodabakhshi, F., Mohebpour, S.R., Eskandari, H. and Haghshenas, M., 2019. Finite element modeling and experimental validation of CGP classical and new cross routes for severe plastic deformation of an Al-Mg alloy. Journal of Manufacturing Processes, 37, pp.348-361.
[18] Nazari, F., Honarpisheh, M. and Zhao, H., 2019. Effect of stress relief annealing on microstructure, mechanical properties, and residual stress of a copper sheet in the constrained groove pressing process. The International Journal of Advanced Manufacturing Technology, 102(9-12), pp.4361-4370.
[19] Mozafari, J., Khodabakhshi, F., Eskandari, H. and Haghshenas, M., 2019. Wear Resistance and Tribological Features of Ultra-Fine-Grained Al-Mg Alloys Processed by Constrained Groove Pressing-Cross Route. Journal of Materials Engineering and Performance, 28(2), pp.1235-1252.
[20] Hoseini-Athar, M.M., Mahmudi, R., Babu, R.P. and Hedström, P., 2019. Microstructural evolution and superplastic behavior of a fine-grained Mg–Gd alloy processed by constrained groove pressing. Materials Science and Engineering: A, 754, pp.390-399.
[21] Wang, Z., Wang, T., Guan, Y., Wei, X., Fang, X., Zhu, G. and Gao, S., 2019. Effects of lubrication and strain path on constrained groove pressing of commercially pure aluminum sheets. The International Journal of Advanced Manufacturing Technology, pp.1-17.
[22] Ghorbanhosseini, S. and Fereshteh-saniee, F., 2019. Multi-objective optimization of geometrical parameters for constrained groove pressing of aluminium sheet using a neural network and the genetic algorithm. Journal of Computational Applied Mechanics, 50(2), pp.275-281.
[23] Ghorbanhosseini, S., Fereshteh-Saniee, F. and Sonboli, A., 2020. Development of new fiber textures for enhancing mechanical properties of 2024 Al alloy using elevated-temperature constrained groove pressing. Materials Science and Engineering: A, 796, p.140210.
[24] Karademir, I., Celik, M.B., Husem, F., Maleki, E., Amanov, A. and Unal, O., 2021. Effects of constrained groove pressing, severe shot peening and ultrasonic nanocrystal surface modification on microstructure and mechanical behavior of S500MC high strength low alloy automotive steel. Applied Surface Science, 538, p.147935.
[25] Keyvani, A., Naseri, M., Imantalab, O., Gholami, D., Babaei, K. and Fattah-alhosseini, A., 2021. Microstructural characterization and electrochemical behavior of nano/ultrafine grained pure copper through constrained groove pressing (CGP). Journal of Materials Research and Technology, 11, pp.1918-1931.
[26] Bhardwaj, A., Gohil, N., Gupta, A.K. and Kumar, S.S., 2021. An experimental investigation on the influence of elevated-temperature constrained groove pressing on the microstructure, mechanical properties and hardening behaviour of Ti6Al4V alloy. Materials Science and Engineering: A, 802, p.140651.
[27] Wang, Z., Wang, T., Guan, Y. and Zhu, L., 2021. Effect of strain path on microstructure and mechanical properties of AZ31 magnesium alloy sheets processed by constrained groove pressing. Materials Science and Engineering: A, 804, p.140794.
[28] Nazari, F., Honarpisheh, M. and Zhao, H., 2021. Effect of the uncertainty of multi-cut contour method and friction coefficient on residual stresses of constrained groove pressing process. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, p.0954406220948908.
[29] Fereshteh-Saniee, F., Ghorbanhosseini, S. and Yaghoubi, S., 2021. A comprehensive comparison between the effect of elevated temperature constrained groove pressing on the microstructural evolutions, crystallographic texture, and mechanical properties of Al 2024 and Mg AZ91D alloys. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, p.09544089211043603.
[30] ASTM E3-11, C., 2017. ASTM standards. Philadelphia: American Society for Testing Materials.
[31] Xing, J., Yang, X., Miura, H. and Sakai, T., 2008. Mechanical properties of magnesium alloy AZ31 after severe plastic deformation. Materials Transactions, 49(1), pp.69-75.
[32] Callister, W.D., 2000. Fundamentals of materials science and engineering. Wiley.
[33] Mao, L., Liu, C., Gao, Y., Han, X., Jiang, S. and Chen, Z., 2017. Microstructure and mechanical anisotropy of the hot rolled Mg-8.1 Al-0.7 Zn-0.15 Ag alloy. Materials Science and Engineering: A, 701, pp.7-15.
[34] Alili, B., Azzeddine, H., Abib, K. and Bradai, D., 2013. Texture evolution in AZ91 alloy after hot rolling and annealing. Transactions of Nonferrous Metals Society of China, 23(8), pp.2215-2221.
[35] Guo, F., Zhang, D., Wu, H., Jiang, L. and Pan, F., 2017. The role of Al content on deformation behavior and related texture evolution during hot rolling of Mg-Al-Zn alloys. Journal of Alloys and Compounds, 695, pp.396-403.
[36] Tolouie, E. and Jamaati, R., 2018. Effect of β–Mg17Al12 phase on microstructure, texture and mechanical properties of AZ91 alloy processed by asymmetric hot rolling. Materials Science and Engineering: A, 738, pp.81-89.
[37] Mukai, T., Yamanoi, M., Watanabe, H. and Higashi, K., 2001. Ductility enhancement in AZ31 magnesium alloy by controlling its grain structure. Scripta materialia, 45(1), pp.89-94.
[38] Kim, W.J., Hong, S.I., Kim, Y.S., Min, S.H., Jeong, H.T. and Lee, J.D., 2003. Texture development and its effect on mechanical properties of an AZ61 Mg alloy fabricated by equal channel angular pressing. Acta materialia, 51(11), pp.3293-3307.
[39] Agnew, S.R., Horton, J.A., Lillo, T.M. and Brown, D.W., 2004. Enhanced ductility in strongly textured magnesium produced by equal channel angular processing. Scripta Materialia, 50(3), pp.377-381.
[40] Kim, W.J., An, C.W., Kim, Y.S. and Hong, S.I., 2002. Mechanical properties and microstructures of an AZ61 Mg Alloy produced by equal channel angular pressing. Scripta materialia, 47(1), pp.39-44.
[41] Randle, V. and Engler, O., 2014. Introduction to texture analysis: macrotexture, microtexture and orientation mapping. CRC press.
[42] Humphreys, F.J. and Hatherly, M., 2012. Recrystallization and related annealing phenomena. Elsevier.
[43] Ghorbanhosseini, S., Fereshteh-Saniee, F. and Sonboli, A., 2020. An experimental investigation on the influence of elevated-temperature constrained groove pressing on the microstructure, mechanical properties, anisotropy and texture of 2024 Al sheets. Journal of Alloys and Compounds, 817, p.152763.
