A New Non-isolated Buck-Boost DC/DC Converter Based on Cuk Topology with Single Switch for Renewable Energy Application

محورهای موضوعی : power electronic

Mustafa Okati ¹ , Mohammad Osmani-Bojd ² , Samira Samimi ³

1 - Department of Electrical Engineering, Zabol Branch, Islamic Azad University, Zabol, Iran
2 - Department of Electrical Engineering, Zahedan Branch, Islamic Azad University, Zahedan, Iran
3 - Department of Mathematics Education, Farhangian University, Zahedan, Iran

تاریخ دریافت : 1403/01/20 تاریخ پذیرش : 1403/05/30 تاریخ انتشار : 1403/07/11

کلید واژه: Buck-Boost Converter, Cuk Converter, Continuous Input/output Current, Switching Device Power, Single Switch,

چکیده مقاله :

This research focuses on an active switch non-isolated buck-boost DC/DC converter based on CUK topology. The suggested converter uses a simpler circuit topology to enable the acquisition of higher voltage gain at lower duty cycle levels. In addition, a continuous input/output current with negative output polarity is displayed by this converter. Compared with the conventional buck-boost converter, the suggested converter can obtain a wider range of the voltage conversion ratio with the same duty cycle. The principles and prominent waveforms of Continuous Conduction Mode (CCM) are explained in this work. The efficiency was examined by substituting parasitic resistance effects for steady-state conditions. The current investigation includes a thorough analysis of parameter design, power loss computation, properties, and a comparative analysis with other non-isolated converters. Finally, a working hardware prototype with a 48-watt power output is created, and the practicality of the proposed converter is confirmed by the empirical data gathered from testing.

چکیده انگلیسی:

This research focuses on an active switch non-isolated buck-boost DC/DC converter based on CUK topology. The suggested converter uses a simpler circuit topology to enable the acquisition of higher voltage gain at lower duty cycle levels. In addition, a continuous input/output current with negative output polarity is displayed by this converter. Compared with the conventional buck-boost converter, the suggested converter can obtain a wider range of the voltage conversion ratio with the same duty cycle. The principles and prominent waveforms of Continuous Conduction Mode (CCM) are explained in this work. The efficiency was examined by substituting parasitic resistance effects for steady-state conditions. The current investigation includes a thorough analysis of parameter design, power loss computation, properties, and a comparative analysis with other non-isolated converters. Finally, a working hardware prototype with a 48-watt power output is created, and the practicality of the proposed converter is confirmed by the empirical data gathered from testing.

منابع و مأخذ:

[1] M. S. Bhaskar, M. Meraj, A. Iqbal, S. Padmana-ban, P. K. Maroti,and R. Alammari, "High gain transformer-less double-duty-triplemode DC/DC converter for DC microgrid,'' IEEE Access, vol. 7, pp. 36353-36370, 2019.
[2] P. K. Maroti, S. Padmanaban, M. S. Bhaskar, M. Meraj, A. Iqbal, and R. Al-Ammari, "High gain three-state switching hybrid boost converter for DC microgrid applications,'' IET Power Electron., vol. 12, no. 14, pp. 3656-3667, Nov. 2019.
[3] M. Forouzesh, Y. P. Siwakoti, S. A. Gorji, F. Blaabjerg, and B. Lehman, "Step-up DC_DC converters: A comprehensive review of voltage boosting techniques, topologies, and applica-tions,'' IEEE Trans. Power Electron., vol. 32, no. 12, pp. 9143-9178, Dec. 2017.
[4] D. Kumar, F. Zare, and A. Ghosh, "DC micro grid technology: System architectures, AC grid interfaces, grounding schemes, power quality, communication networks, applications, and standardizations aspects,'' IEEE Access, vol. 5, pp. 12230-12256, 2017.
[5] N. Swaminathan and N. Lakshminarasamma, "The steady-state DC gain loss model, efficiency model, and the design guidelines for high-power, high-gain, low-input voltage DC_DC converter,'' IEEE Trans. Ind. Appl., vol. 54, no. 2, pp. 1542-1554, Mar. 2018.
[6] R. Moradpour, H. Ardi, and A. Tavakoli, ``De-sign and implementation of a new SEPIC-based high step-up DC/DC converter for renewable en-ergy applications,'' IEEE Trans. Ind. Electron., vol. 65, no. 2, pp. 1290-1297, Feb. 2018.
[7] P. K. Maroti, S. Esmaeili, A. Iqbal, and M. Meraj, "High step-up single switch quadratic modified SEPIC converter for DC microgrid applications,'' IET Power Electron., vol. 13, no. 16, pp. 3717-3726, Dec. 2020.
[8] I. Laird and D. D.-C. Lu, "High step-up DC/DC topology and MPPT algorithm for use with a thermoelectric generator,'' IEEE Trans. Power Electron., vol. 28, no. 7, pp. 3147-3157, Jul. 2013.
[9] E. Babaei, H. Mashinchi Maheri, M. Sabahi, and S. H. Hosseini, "Extendable nonisolated high gain DC_DC converter based on active passive inductor cells,'' IEEE Trans. Ind. Electron., vol. 65, no. 12, pp. 9478-9487, Dec. 2018.
[10] M. Lakshmi and S. Hemamalini, "Nonisolated high gain DC_DC converter for DC microgrids,'' IEEE Trans. Ind. Electron., vol. 65, no. 2, pp. 1205-1212, Feb. 2018.
[11] M. Forouzesh, K. Yari, A. Baghramian, and S. Hasanpour, "Single-switch high step-up convert-er based on coupled inductor and switched ca-pacitor techniques with quasi-resonant opera-tion,'' IET Power Electron., vol. 10, no. 2, pp. 240-250, Feb. 2017.
[12] H.-L. Jou, J.-J. Huang, J.-C.Wu, and K.-D.Wu, "Novel isolated multilevel DC_DC power con-verter,'' IEEE Trans. Power Electron., vol. 31, no. 4, pp. 2690-2694, Apr. 2016.
[13] G. Catona, E. Bianconi, R. Maceratini, G. Cop-pola, L. Fumagalli, G. Petrone, and G. Spagnuo-lo, "An isolated semi resonant DC/DC converter for high power applications,'' IEEE Trans. Ind. Appl., vol. 53, no. 3, pp. 2200-2209, May 2017.
[14] V. R. K. Kanamarlapudi, B.Wang, N. K. Kan-dasamy, and P. L. So, "A new ZVS full-bridge DC_DC converter for battery charging with re-duced losses over full-load range,'' IEEE Trans. Ind. Appl., vol. 54, no. 1, pp. 571-579, Feb. 2018.
[15] S. Dwari and L. Parsa, "An efficient high-step-up interleaved DC_DC converter with a common active clamp,'' IEEE Trans. Power Electron., vol. 26, no. 1, pp. 66-78, Jan. 2011.
[16] G. Tibola, E. Lemmen, J. L. Duarte, and I. Barbi, "Passive regenerative and dissipative snubber cells for isolated SEPIC converters: Analysis, design, and comparison,'' IEEE Trans. Power Electron., vol. 32, no. 12, pp. 9210-9222, Dec. 2017.
[17] F. L. Tofoli, D. D. C. Pereira, W. J. de Paula, and D. D. S. O. Júnior, "Survey on non-isolated high- voltage step-up DC_DC topologies based on the boost converter,'' IET Power Electron., vol. 8, no. 10, pp. 2044-2057, Oct. 2015.
[18] F. Mohammadzadeh Shahir, E. Babaei, and M. Farsadi, "Analysis and design of voltage-lift technique-based non-isolated boost DC-DC con-verter,'' IET Power Electron., vol. 11, no. 6, pp. 1083-1091, May 2018.
[19] Y. Tang, D. Fu, T.Wang, and Z. Xu, ``Hybrid switched-inductor converters for high step-up conversion,'' IEEE Trans. Ind. Electron., vol. 62, no. 3, pp. 1480-1490, Mar. 2015.
[20] N. Genc and I. Iskender, "DSP-based current sharing of average current controlled two-cell interleaved boost power factor correction converter,'' IET Power Electron., vol. 4, no. 9, pp. 1015-1022, Nov. 2011.
[21] B. Axelrod, Y. Berkovich, and A. Ioinovici, "Switched capacitor/ switched-inductor struc-tures for getting transformerless hybrid DC_DC PWM converters,'' IEEE Trans. Cir-cuits Syst. I, Reg. Papers, vol. 55, no. 2, pp. 687-696, Mar. 2008.
[22] N. Zhang, G. Zhang, K. W. See, and B. Zhang, "A Single-Switch Quadratic Buck–Boost Converter With Continuous Input Port Current and Continuous Output Port Current," IEEE Transactions on Power Electronics, vol. 33, pp. 4157-4166, 2018.
[23] M. R. Banaei, and H. A. F. Bonab, "A High Efficiency Non-Isolated Buck-Boost Con-verter Based on ZETA Converter,” IEEE Transactions on Industrial Electronics, vol. 67, pp. 1991-1998, 2019.
[24] A. Sarikhani, B. Allahverdinejad, M. Hamzeh, and E. Afjei, "A continuous input and output current quadratic buck-boost converter with positive output voltage for photovoltaic applications," Solar Energy, vol. 188, pp. 19-27, 2019.
[25] M. Veerachary and M. R. Khuntia, "Design and Analysis of Two-Switch-Based En-hanced Gain Buck–Boost Converters," IEEE Transactions on Industrial Electronics, vol. 69, pp. 3577-3587, April 2022.
[26] M. Okati, M. Eslami, M. J. Shahbazzadeh, and H. Shareef, "A New Transformerless Quadratic Buck–Boost Converter with High Voltage Gain Ratio and Continuous In-put/output Current Port," IET Power Elec-tronics, vol. 15, pp.1280-1294, 2022.
[27] J. Li and J. Liu, "A Novel Buck–Boost Con-verter with Low Electric Stress on Compo-nents," IEEE Transactions on Industrial Electronics, vol. 66, pp. 2703-2713, 2019.
[28] J. Divya Navamani, A. Lavanya, D. Alma-khles, and M. Jagabar Sathik, "A review on segregation of various high gain converter configurations for distributed energy sources, " Alexandria Engineering Journal, vol. 61, no. 1, pp. 675-700, Jan, 2022.
[29] F. Mumtaz, N. Zaihar Yahaya, S. Tanzim Meraj, B. Singh, R. Kannan, and O. Ibrahim, "Review on non-isolated DC-DC converters and their con-trol techniques for renewable energy applica-tions," Ain Shams Engineering Journal, 2021.
[30] M. Shen, A. Joseph, J. Wang, F. Z. Peng, and D. J. Adams, "Comparison of Traditional Inverters and Z -Source Inverter for Fuel Cell Vehicles," IEEE Transactions on Power Electronics, vol. 22, pp. 1453-1463, 20