Assessment the Wear Properties of Biodiesel-diesel Blends with the Addition of Copper Oxide Nanoparticles

Subject Areas :

Hossein  Khorshidnia ¹ (Department of Mechanical Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran)
Alireza  Shirneshan ² (Department of Mechanical Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran|Aerospace and Energy Conversion Research Center, Najafabad Branch, Islamic Azad University, Najafabad, Iran)

Received: 2019-11-19 Accepted : 2020-03-03 Published : 2019-11-01

Keywords: nanoparticles, Copper oxide, Wear, Wear Scar Diameter,

Abstract :

Normal lubricants such as petroleum, coals or natural gases are limited and will keep depleting due to high fuel consumption all over the world; so nano-lubricants can be considered as the alternatives. In the present study, copper oxide nanoparticles were mixed with biodiesel-diesel blends to evaluate the wear properties of the mixture by 4-ball wear tribo-tester. CuO nanoparticles (25, 50 and 75 ppm) were dispersed in B10, B20, and B50 blends. The results showed that with increasing the CuO nanoparticle fraction up to 50 ppm in the fuel blend, the wear scar diameter (WSD) decreased. Also, the results indicated that using copper oxide nanoparticles with a dosage of 75 ppm in the fuel blend causes a higher WSD compared with 50 ppm dosage. Based on the results, the scratches and roughness on the surface also decreased with an increase of biodiesel concentration and addition of nanoparticles up to 50 ppm in the fuel mixture.

References:

[1] Choi, Y., Lee, C., Hwang, Y., Park, M., Lee, J. and Choi, C. 2009. Tribological behaviour of copper nanoparticles as additive in oil. Current Applied Physics. 9(2): 124–127.

[2] Syaima, M.T.S, Zamratul, M.I.M., Nor, I.M. and Rifdi, W. 2014. Development of bio-lubricant from Jatropha curcas oils. International Journal of Research in Chemical, Metallurgical and Civil Engineering. 1(1):10-12.

[3] Shafiee, S. and Topal, E. 2009. When will fossil fuel reserves be diminished? Energy Policy. 37:181–9.

[4] Sangeeta, A., Moka, S., Pande, M., Rani, M., Gakhar. R. and Sharma, M. 2014. Alternative fuels: An overview of current trends. Renewable and Sustainable Energy Reviews. 32:697-712.

[5] Serrano, L.M.V., Camara, R.M.O., Carreira, V.J.R. and Gameiro da Silva, M.C. 2012. Performance study about biodiesel impact on buses engines using dynamometer tests and fleet consumption data. Energy Conversion and Management. 60:2–9.

[6] Knothe, G. and Steidley, K.R. 2005. Lubricity of components of biodiesel and petrodiesel: The origin of biodiesel lubricity. Energy & Fuels. 19:1192–200.

[7] Sarvi, A., Fogelholm, C.J., Zevenhoven, R. 2008. Emissions from large-scale medium speed diesel engines: 2– Influence of fuel type and operating mode. Fuel Processing Technology. 89:520–7.

[8] Nwafor, O.M.I. 2003. The effect of elevated fuel inlet temperature on performance of diesel engine running on neat vegetable oil at constant speed conditions. Renewable Energy. 28:171–81.

[9] He-long, Y., Yi, X., Pei-jing, S., Bin-shi, X., Xiao-li, W. and Qian, L. 2008. Tribological properties and lubricating mechanisms of Cu nanoparticles in lubricant. Transactions of Nonferrous Metals Society of China. 18(3):636-641.

[10] Zulkifli, N.W.M., Kalam, M.A., Masjuki, H.H. and Yunus, R. 2013. Experimental analysis of tribological properties of chemically modified bio-based lubricant with nanoparticles additives. Procedia Engineering. 68:152-157.

[11] Zhang, Z.J., Simionesie, D. and Schaschke, C. 2014. Graphite and hybrid nanometerials as lubricant additive. Lubricants. 2(2), 44-65.

[12] Gu, C., Zhu, G., Li, L., Tian, X. and Zhu, G. 2009. Tribological effect of oxide base nanoparticles in lubricating oils. Journal of Marine Science and Application. 8:71–76.

[13] Padgurskas, J., Rukuiza, R., Prosycevas, I. and Kreivaitis, R. 2013. Tribological properties of lubricant additive of Fe, Cu and Co nanoparticles. Tribology International. 60:224-232.

[14] Abdullah, M., Abdollah, M., Amiruddin, H., Tamaldin, N. and Nuri, N. 2014. Effect of hBN/Al2O3 nanoparticles on the tribological performance of engine oil. Jurnal Teknologi. 66(3):1–6.

[15] Wu, Y.Y., Tsui, W.C. and Liu, T.C. 2007. Experimental analysis of tribological properties of lubricating oils with nanoparticles additive. Wear. 262(7–8):819-825.

[16] Asnida, M., Hisham, S., Awang, N.W., Amirruddin, A.K., Noor, M.M., Kadirgama, K., Ramasamy, D., Najafi, G. and Tarlatan F. Copper (II) oxide nanoparticles as additve in engine oil to increase the durability of piston-liner contact. Fuel. 212: 656-667.

[17] Battez, A.H., Gonzalez, R., Viesca, J.L., Fernandez, J.E., Fernandez, J.M.D. and Machado, A. 2008. CuO, ZrO2 and ZnO nanoparticles as antiwear additive in oil lubricants. Wear. 265(3–4): 422-428.

[18] Wu, Y. Y., Tsui, W. C. and Liu, T. C. 2007. Experimental analysis of tribological properties of lubricating oils with nanoparticles additives. Wear. 262(7): 819-825.

[19] Padgurskas, J., Rukuiza, R.,   Prosyčevas, I. and Kreivaitis, R. 2013. Tribological properties of lubricant additives of Fe, Cu and Co nanoparticles. Tribology International. 60: 224-232.

[20] Kotia, A., Borkakoti, S. and Kumar Ghosh, S. 2018. Wear and performance analysis of a 4-stroke diesel engine employing nanolubricants. Particuology. 37:54-63.

[21] Dai,W., Kheireddin, B., Gao, H. and Liang, H. 2016. Roles of nanoparticles in oil lubrication. Tribology International.102:88–98.

[22] Fazal, M. A., Haseeb, A. S. M. A. and Masjuki, H. H. 2013. Investigation of friction and wear characteristics of palm biodiesel. Energy Conversion and Management. 67:251-256.

[23] Fazal, M. A., Haseeb, A. S. M. A. and Masjuki, H. H. 2014. A Critical Review on the tribological compatibility of automotive materials in palm biodiesel. Energy Conversion and Management. 79:180-186.

[24] Fazal, M. A., Haseeb, A. S. M. A. and Masjuki, H. H. 2013. Corrosion mechanism of copper in palm biodiesel. Corrosion Science. 67:50-59.

[25] Hu, J., Du, Z., Li, C. and Min, E. 2005. Study on the lubrication properties of biodiesel as fuel lubricity enhancers. Fuel. 84(12–13):1601-1606.

[26] Barsari, M. A. N. and Shirneshan, A. 2019. An Experimental study of friction and wear characteristics of sunflower and soybean oil methyl ester under the steady-state conditions by the four-ball wear testing machine. Journal of Tribology. 141(4):044501-044501-10.