Effect of Ablation Casting on Microstructure of a Magnesium Alloy
Subject Areas : journal of New MaterialsM. Ghasvari 1 , S. M. Boutorabi 2
1 - Graduated of material science and engineering department, Iran University of Science & Technology (IUST), Tehran, Iran
2 - Material science and engineering, faculty, Iran University of Science & Technology, Tehran, Iran
Keywords: Ablation casting, AZ81 alloy, grain refinement, precipitates, porosity,
Abstract :
Grain growth is a challenge in AZ magnesium alloys casting. The purpose of this research was to develop a finer microstructure than the conventional sand casting. In this study, a new method ablation casting was used. In the ablation casting method the mold must be washed after pouring and before the part complete solidification. In this way the part solidification rate increases. The sand mold was washed by water pressure 30 seconds after pouring in order to remove the heat content of the piece only by water. Thermal analysis was done by thermocouples that were placed in certain positions in mold. Then the cooling rates of samples were measured by them. The cooling rates in mushy zone were 1.27 and 0.52°C/sec for ablated and conventional casting parts respectively. The Cooling rate of the ablated part was 2.42 times further than the conventional CO2 sand casting. Size of dendrites decreased from 164.5 to 46.9µm with increasing cooling rate. During the solidification temperature gradients between two points of the ablated part was measured to predict of dendritic solidification. The temperature gradient mean between these points was 1.12°C/mm. In ablated sample, eutectic phase volume percent and precipitates were reduced. There was no change in shape of the pores in the ablated sample, but the volume percent of pores and maximum size was reduced. The average pore diameters were 82 and 42µm in ablated and control sample respectively.
References:
1-M. Sahoo, Technology for Magnesium Castings : design, products & applications, 1st ed., pp. 1-9, American Foundry Society, Schaumburg, 2011.
2-K. U. Kainer, Magnesium Alloys and Technology, p. 18, Wiley-VCH, Geesthacht, 2003.
3- ن. بیات ترک و همکاران، "بررسی قابلیت تغییر شکل منیزیم خالص و آلیاژ AZ91، در دمای پایین با کاربرد فرآیند اکستروژن برشی ساده"، مجله مواد نوین، دورهی1، شمارهی 2، ص 41-48، زمستان 1389.
4-J. R. Grassi, J. Campbell and G. Kuhlman, “Mold-Removal Casting Method And Apparatus“, Google Patents, WO 2004/004948 A2, 2004.
5-M. Alderman, M. V. Manuel, N. Hort and N. R. Neelameggham, Magnesium Technology 2014, p. 5, Wiley & Sons, New Jersey, 2014.
6-J. W. Zindel, “Ablation Casting Evaluation for High Volume Structural Castings”, p. 3, USAMP, 2012.
7-T. J. Williams, D. Galles, and C. Beckermann, “Translating Water Spray Cooling of a Steel Bar Sand Casting”, 67th SFSA Technical and Operating Conference, Iowa, pp. 1-10, 2013.
8-J. Grassi, J. Campbell, M. Hartlieb and F. Major, “The Ablation Casting Process”, Materials Science Forum, Vol. 618-619, pp. 591-594, 2009.
9-J. Campbell, Complete Casting Handbook, 2nd ed., p. 1018, Elsevier, Waltham, 2011.
10-A. A. Lou, “Magnesium casting technology for structural applications”, Journal of Magnesium and Alloys, Vol. 1, 1, pp. 2-22, 2013.
11-W. Baldwin, "Metallography and Microstructures of Magnesium and Its Alloys", ASM Metals Handbook, Vol. 9, pp. 1943-1986, 2004.
12-K. Pettersen, O. Lohne, and N. Ryum, “Dendritic solidification of magnesium alloy AZ91” Metallurgical Transactions A, Vol. 21 A, pp. 221-230, 1990.
13-P. Sharifi, “Property Relationships of Magnesium Alloys”, ph. D. Thesis University of Western Ontario, Ontario, 2012.
14-M. Ferry, Direct strip casting of metals and alloys, 1st ed., p. 90, CRC Press, Boca Raton, 2006.
15-Md. Imran Khan, A. O. Mostafa, M. Aljarrah, E. Essadiqi, and Mamoun Medraj, “Influence of Cooling Rate on Microsegregation Behavior of Magnesium Alloys”, Journal of Materials, pp. 1-18, 2014.
16- K.N. Braszczyńska-Malik, “Precipitates of γ–Mg17Al12 Phase in AZ91 Alloy”, Magnesium Alloys - Design, Processing and Properties, pp. 95-112, 2002.
17-O. Sabokpa, A. Zarei-Hanzaki and H. R. Abedi, “An investigation into the hot ductility behavior of AZ81 magnesium alloy”, Materials Science and Engineering A, Vol. 550, pp. 31–38, 2012.
18-M. Nazmul Khan, “Solidification study of commercial magnesium alloys” MSc Thesis Concordia University, Montreal, 2009.
19-D. H. StJohn, A. K. Dahle, T. Abbott, M. D. Nave, and Ma Qian, “Solidification of Cast Magnesium Alloys”, Magnesium Technology 2003, 2003.
20-J. B. Duval, Foundry Manual, 1st ed., p. 2, Bureau for Shipbuilding and Fleet, Washington, 1958.
_||_