Effect of Sr on Microstructure and Mechanical Properties of AZ91 Magnesium Alloy

Subject Areas : journal of New Materials

A. Afsharnaderi ¹ (MSc student, School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, Tehran)
J. Rasizadeh ² (- Associate Professor, School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, Tehran)
M. Malekan ³ (Assistant Professor, School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, Tehran)
M. Emamy ⁴ (Professor, School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, Tehran)

Received: 2017-07-18 Accepted : 2017-08-27 Published : 2018-07-23

Keywords: Microstructure, mechanical properties, Grain size, AZ91 magnesium alloy, strontium (Sr),

Abstract :

       In this study, the effect of different amounts of Sr (0, 0.05, 0.5, 1 wt.%) was investigated on microstructure and mechanical properties of the AZ91 magnesium alloy. The microstructure and mechanical properties were investigated using optical microscope, scanning electron microscope (SEM), X-ray diffractometer (XRD) and tensile test. The results shown that by adding Sr, the volume fraction of the Mg₁₇Al₁₂ phase decreased. It was also found that the grain size decreased significantly by addition of Sr, after homogenization. In this case, the grain size decreased from 131 μm in AZ91 to 43 μm in AZ91 with 1 wt.% Sr. Furthermore, the optimum amount of UTS and elongation were observed by the addition of 1 wt.% Sr to AZ91 magnesium alloy. UTS and elongation increased from 129 MPa and 1.1% to 177 MPa and 2%, respectively, when the 1 wt.% Sr was added to the AZ91 alloy. The fracture surface observations showed that fracture mode in these alloys were cleavage and the Sr addition does not change the fracture mode.

References:

References:

1- B. L. Mordike, T. Ebert, Magnesium: Properties -Applications-Potential, Materials Science and Engineering, Vol. 302, pp. 37-45, 2001.

2- K. U. Kainer, Magnesium Alloys and Technology, Wiley-VCH, Verlag GmbH & Co. KGaA, 2003.

3- X. Q. Zhang, Y. X. Wang, W. J. Ding, “Effect of Strontium on the Microstructure, Mechanical properties and Fracture Behavior of AZ31 Magnesium Alloys”, Metal Mater Trans, Vol. 37, pp. 1333-1341, 2006.

4- R. J. Chen, A. T. Tang, M. B. Yang, F. S. Pan, “Effects of Al-Sr Master Alloys on the As-Cast Microstructure of the AZ31 Magnesium Alloys”, Materials Science Forum, Vol 546, pp 183-186. , 2007.

5- A. Srinivasan, U. T. Pillai, J. Swaminathan, S. K. Das, B. C. Pai, “Observations of Microstructural Refinement in Mg-Al-Si Alloys Containing Strontium”, Journal of Materials Science, Vol. 41, pp. 6087-6089, 2006.

6- K. Y. Nam, D. H. Song, C. W. Lee, “Modification of Mg₂Si Morphology In As-Cast Mg-Al-Si Alloys With Strontium and Antimony”. Materials Science Forum, Vol 510, pp. 224-238, 2006.

7- B. Chen, D. L Lin, L. Jin, X. Q. Zeng, C. Lu, “Equal-channel angular pressing of magnesium alloy AZ91 and its effects on microstructure and mechanical properties”, Materials Science and Engineering, Vol. 483-484, pp. 113-116, 2008.

8- E. Cerri, P. Leo, P. De Marco, “Hot Compression Behavior of the AZ91 Magnesium Alloy Produced by High Pressure die casting”, Journal of Materials Processing Technology, Vol. 189, pp. 97-106, 2007.

9- M. M. Avedesian, H. Baker, Magnesium and Magnesium Alloys. ASM Specialty Handbook, Materials Park, ASM International, 1999.

10- I. A. Yakubtsov, B. J  Diak, C. A. Sager, B. Bhattacharya, W. D. Macdonald, M. Niewcsaz, “Effects of Heat Treatment on Microstructure and Tensile Deformation of Mg AZ80 Alloy at Room Temperature”, Materials Science and Engineering, Vol. 496, pp. 247-255, 2008.

11- A. V. Koltygin, T. A. Bazlova, and I. V. Plisetskaya, “Effect of Calcium on The Process of Production and Structure of Magnesium Melted by Flux-Free Method”, Metal Science and Heat Treatment, Vol. 54, Nos. 9 – 10, January, 2013.

12- H. Chandler, “Heat Treater’s Guide practices and procedures for Nonferrous Alloys”, The Materials Information Society, ASM International, 3^rd Edition, March, 2006.

13- A. Kielbus, L. Cizek, L. Pawlica, “Microstructural Changes of AZ91 Magnesium Alloy After Heat Treatment”, 6th International Conference Magnesium Alloys and Their Applications. Ed.: Kainer, K. U. Weinheim, Wiley-VCH Verlag GmbH, pp. 196-202. 2004.

14- Wang Qu-dong, Chen Wen-zhou, Zeng Xiao-qin, Lu Yi-zhen, Ding Wen-jiang, Zhu Yan-ping, Xu Xiao-ping, “Effects of Ca Addition on the Microstructure and Mechanical Properties of AZ91 Magnesium Alloy”, Journal of Materials Science, Vol. 36, pp. 3035-3040, 2001.

15- Y. Cheng, T. Qin, H. Wang, Z. Zhang, “Comparison of Corrosion Behaviors of AZ31, AZ91, AM60 and ZK60 Magnesium alloys”, Trans. Nonferrous Met. Soc., China, Vol. 19, pp 517-524, 2009.

16- S. Lee, S. H. Lee, D. H.  Kim, “Effect of Y, Sr and Nd Addition in the Microstructure and Microfracture Mechanism of Squeeze-Cast AZ91x Magnesium Alloys”, Metal Mater Trans, Vol. 29, pp 1221-1235, 1998.

17- Y. C. Lee, D. H. StJohn, J. E. C. Hutt, A. K. Dahle, “Effect of Grain Refinement and Silicon Content on Grain Formation in Hypoeutectic Al-Si Alloys”, Materials Science and Engineering, Vol. 259, pp. 43-52, 1999.

18- J. E. C. Hutt, A. K. Dahle, Y. C. Lee, D. H. StJohn, “Effects of Growth Restriction and Effective Nucleant Potency on Grain Size and Morphology in Al-Si and Al-Cu Alloys”, Light Metals: Proceedings of Sessions, TMS Annual Meeting. Warrendale, PA, USA, Minerals, Metals & Materials Society (TMS), pp. 685-692, 1999.

19- A. K. Dahle, Y. C. Lee, M. D. Nave, P. L. Schaffer, D. H. StJohn, “Development of As-Cast Microstructure in Magnesium-Aluminum Alloys”. Journal of Light Metals, Vol. 1, pp. 61-72, 2001.

20- Y. Z. Lu, Q. D. Wang, W. J. Ding, X. Q. Zeng, Y. P. Zhu, “Fracture Behavior of AZ91 Magnesium alloy”, Materials Letters, Vol. 44, pp. 265-268, 2000.