Study on microstructure and mechanical properties of API X70 steel at various hot rolling conditions

Subject Areas : journal of New Materials

محسن ریحانیان ¹ , Mehdi Rezaei ² , Mostafa Eskandari ³

1 - استاد دانشگاه چمران اهواز
2 - Department of Materials Science and Engineering, Faculty of Engineering, Shahid Chamran University of Ahvaz, Ahvaz, Iran
3 - Department of Materials Science and Engineering, Faculty of Engineering, Shahid Chamran University of Ahvaz, Ahvaz, Iran

Received: 2020-08-01 Accepted : 2021-01-11 Published : 2020-11-21

Keywords: Microstructure, mechanical properties, API X70 steel, Hot rolling, Thermomechanical controlled processing (TMCP),

Abstract :

In the present work, API X70 steel, a type of high strength low alloy (HSLA) steel, hot-rolled at different conditions and the effect of various hot rolling parameters on microstructure and mechanical properties investigated through thermomechanical control processing (TMCP). Optical and scanning electron microscopy were used for microstructural investigations and the tensile and hardness test utilized for mechanical characterization. The steel preheated at 1250 for 30 min and hot rolled with the speed of 10 rpm in the temperature range of 1100 to 730 through 3 (sample A), 4 (sample B), and 5 (sample C) passes and cooled in air. A total strain of 0.62 was imposed on all samples. In the 5 pass condition, a sample rolled with a finishing rolling temperature of 900 (sample D), another with a speed of 20 rpm, and the rest (sample E) rolled and quenched in water (sample F). Results showed that, except for sample E, all samples' microstructure consists of ferrite and pearlite but with different morphology. Sample E showed the least grain size. Due to the formation of the quasi-stable phases, sample F exhibited the highest strength/hardness and the lowest ductility. The best combination of strength and ductility was achieved in sample E.

References:

1- W.B. Morrison, Microalloy steels – the beginning, Materials Science and Technology, 25 (2009) 1066-1073.           

2- A.J. DeArdo, M.J. Hua, K.G. Cho, C.I. Garcia, On strength of microalloyed steels: an interpretive review, Materials Science and Technology, 25 (2009) 1074-1082.

3- T.N. Baker, Microalloyed steels, Ironmaking & Steelmaking, 43 (2016) 264-307.

4- I. Olivares, M. Alanis, R. Mendoza, B. Campillo, J.A. Juarez-Islas, Development of microalloyed steel for pipeline applications, Ironmaking & Steelmaking, 35 (2008) 452-457.

5- J. Zhao, Z. Jiang, Thermomechanical processing of advanced high strength steels, Progress

 

in Materials Science, 94 (2018) 174-242.

6- S. Vervynckt, K. Verbeken, B. Lopez, J.J. Jonas, Modern HSLA steels and role of non-recrystallisation temperature, International Materials Reviews, 57 (2012) 187-207.  

7- A.J. Deardo, Niobium in modern steels, International Materials Reviews, 48 (2003) 371-402.   

8- T. Sakai, A. Belyakov, R. Kaibyshev, H. Miura, J.J. Jonas, Dynamic and post-dynamic recrystallization under hot, cold and severe plastic deformation conditions, Progress in Materials Science, 60 (2014) 130-207.    

9- A.R.H. Far, S.H.M. Anijdan, S.M. Abbasi, The effect of increasing Cu and Ni on a significant enhancement of mechanical properties of high strength low alloy, low carbon steels of HSLA-100 type, Materials Science and Engineering: A, 746 (2019) 384-393.

10- S. Nemat-Nasser, W.-G. Guo, Thermomechanical response of HSLA-65 steel plates: experiments and modeling, Mechanics of Materials, 37 (2005) 379-405.        

11- L.d.J. Jorge, V.S. Cândido, A.C.R.d. Silva, F.d.C. Garcia Filho, A.C. Pereira, F.S.d. Luz, S.N. Monteiro, Mechanical properties and microstructure of SMAW welded and thermically treated HSLA-80 steel, Journal of Materials Research and Technology, 7 (2018) 598-605.       

12- H. Izadi, M. Tavakoli, M.H. Moayed, Effect of thermomechanical processing on hydrogen permeation in API X70 pipeline steel, Materials Chemistry and Physics, 220 (2018) 360-365.

13- A.A. Gorni, P.R. Mei, Effect of controlled-rolling parameters on the ageing response of HSLA-80 steel, Journal of Materials Processing Technology, 197 (2008) 374-378.   

14- S.K. Dhua, D. Mukerjee, D.S. Sarma, Influence of thermomechanical treatments on the microstructure and mechanical properties of HSLA-100 steel plates, Metallurgical and Materials Transactions A, 34 (2003) 241-253.

15- C. Ouchi, T. Sampei, I. Kozasu, The Effect of Hot Rolling Condition and Chemical Composition on the Onset Temperature of γ-α Transformation after Hot Rolling, Transactions of the Iron and Steel Institute of Japan, 22 (1982) 214-222.

16- A. Hossain Seikh, M.S. Soliman, A. AlMajid, K. Alhajeri, W. Alshalfan, Austenite Grain Growth Kinetics in API X65 and X70 Line-Pipe Steels during Isothermal Heating, Advances in Materials Science and Engineering, 2014 (2014) 246143.    

17- Y.G. Ko, M.J. Kim, K. Hamad, Structural evolutions and mechanical properties of IF steel deformed by differential speed rolling at various per-pass-thickness reductions, Materials Letters, 250 (2019) 178-181.

18- Å. Sjöström, The effect of high reductions per pass on material properties in the hot rolling of low-alloyed steel, Journal of Mechanical Working Technology, 6 (1982) 347-360.

19- R. Grewal, C. Aranas, K. Chadha, D. Shahriari, M. Jahazi, J.J. Jonas, Formation of Widmanstätten ferrite at very high temperatures in the austenite phase field, Acta Materialia, 109 (2016) 23-31.

20- Y. Han, J. Shi, L. Xu, W.Q. Cao, H. Dong, Effect of hot rolling temperature on grain size and precipitation hardening in a Ti-microalloyed low-carbon martensitic steel, Materials Science and Engineering: A, 553 (2012) 192-199.

21-B. Guo, L. Fan, Q. Wang, Z. Fu, Q. Wang, F. Zhang, Effect of Finish Rolling Temperature on the Microstructure and Tensile Properties of Nb–Ti Microalloyed X90 Pipeline Steel, Metals, 6 (2016) 323.  

22- I. Dey, S.K. Ghosh, R. Saha, Effects of cooling rate and strain rate on phase transformation, microstructure and mechanical behaviour of thermomechanically processed pearlitic steel, Journal of Materials Research and Technology, 8 (2019) 2685-2698.      

23- M. Katsumata, O. Ishiyama, T. Inoue, T. Tanaka, Microstructure and Mechanical Properties of Bainite Containing Martensite and Retained Austenite in Low Carbon HSLA Steels, Materials Transactions, JIM, 32 (1991) 715-728.

24- B.C. Muddle, J.F. Nie, Formation of bainite as a diffusional–displacive phase transformation, Scripta Materialia, 47 (2002) 187-192.