Investigating the Rheological Behavior of Silicon Carbide Gel Casting Suspensions and its Effect on the Silicon Carbide Bodies

Subject Areas : journal of New Materials

Hesam Fallah-Arani ¹ , Salah Isafi ² , Parinaz Tabrizian ³ , Saeid Baghshahi ⁴

1 - Non-metallic Materials Research Group, Niroo Research Institute (NRI), Tehran, Iran
2 - Non-metallic Materials Research Group, Niroo Research Institute (NRI), Tehran, Iran
3 - Non-metallic Materials Research Group, Niroo Research Institute (NRI), Tehran, Iran.
4 - Dept. of Materials Eng., Imam Khomeini International University, Qazvin, Iran

Received: 2018-05-25 Accepted : 2019-05-05 Published : 2019-04-21

Keywords: Silicon carbide, Gel-casting, Rheological behavior, Flexural Strength,

Abstract :

In this paper, the rheological behavior of SiC suspensions, fabricated via gel-casting method, and the influence of this behavior on the mechanical properties of the sintered samples were studied. To prepare castable and stable SiC suspensions, the rheological behaviour of the suspensions was characterized and optimized. To this aim tetramethylammonium hydroxide as dispersant, acrylamide as monomer, methylenebisacrylamide as cross linker, ammonium persulfate as initiator and tetramethylethylenediamine as catalyst were used. The results indicated that for obtaining stable SiC suspensions with suitable viscosity, 0.4 wt% dispersant of tetramethylammonium hydroxide, the pH of 10.5 and mixing time of 24 h were required. It should be noted that this suspension was electrosterically stable and the presence of the monomer acrylamide decreased the viscosity. The results showed that in the optimal ratio of methylenebisacrylamide cross linker to acrylamide monomer the highest strength was obtained. The flexural strength of the gel cast bodies was 231 MPa.

References:

References:
1- I. Ganesh, D. C. Jana, S. Shaik, N. Thiyagarajan,. An aqueous gelcasting process for sintered silicon carbide ceramics. J. Am. Ceram. Soc., 89(10)(2006), 3056-3064.
2 - ج. پوراسد، ن. احسانی، ع. خلیفه سلطانی،
"بررسی مسیر واکنشی تشکیل پوشش تدریجی SiC
بر گرافیت با روش سمانتاسیون بستهای و تاثیر نوع
مواد اولیه" مجله علمی پژوهشی مواد نوین، جلد 7 ،
شماره 4، تابستان 96 ، ص 46 - 39 .
3-
4- D. Jiang, “Gelcasting of carbide ceramics”, J Ceram Soc JPN, 116.1354 (2008), 694-699.
5- D. C. Jana, G. Sundararajan and K. Chattopadhyay, “Effect of monomers content in enhancing solid-state densification of silicon carbide ceramics by aqueous gelcasting and pressureless sintering”,Ceram. Int 43 (2017), 4852-4857.
6- Y. Huang and J. Yang, “Novel Colloidal Forming of Ceramics”. Springer, New York, 2010.
7- M. A. Janney, O. O. Omatete, C. A. Walls, S. D. Nunn, R. J. Ogle, G. Westmoreland, “Development of low‐toxicity
gelcasting systems”. J. Am. Ceram. Soc, 81(3)(1998), 581-591.
8- N. O. Shanti, D. B. Hovis, M. E. Seitz, J. K. Montgomery, D. M. Baskin, K. T. Faber, Ceramic laminates by gelcasting. Int. J. Appl. Ceram. Technol, 6(5)(2009), 593-606.
9- Q. Zhang and M. Gu, “Rheological properties and gel casting of concentrated aqueous silicon suspension”, Mater. Sci. Eng., 399 )2005) 351-357.
10- A. C. Young, O. O. Omatete, M. A. Janney, and P. A. Menchhofe, “Gelcasting of Alumina”, J. Am. Ceram. Soc., 74 (1991) 612-618.
11- M. Janney, C. Walls, O. O. Omatete, and R. Ogle, Gel casting, 1998.
12- M. Potoczek and E. Zawadzak, “Initiator effect on the gelcasting properties of alumina in a system involving low-toxic monomers”, Ceram. Int., 30 (2004) 793-799.
13- A. Barati, M. Kokabi, and M. H. N. Famili, “Drying of gelcast ceramic parts viathe liquid desiccant method”, J. Eur. Ceram. Soc.,23(2003) 2265-2272.
14- R. Gilissen, J. Erauw, A. Smolders, E. Vanswijgenhoven, and J. Luyten, “Gelcasting, a near net shape techniquent”, Mater. Des., 2(2000) 251-257.
88 بررسی رفتار رئولوژی دوغابهای ریختهگری ژلی کاربید سیلیسیم و تاثیر آن بر خواص مکانیکی بدنههای...
15- P. Tabrizian, F. Golestanifard, A. Alem, and E. Ghassemi, “The influence of gelcasting parameters on the preparation of Si porous bodies”, Mater. Lett., 183(2016), 19-22.
16- K. Mohanta and P. Bhargava, “Effect of Milling Time on the Rheology of Highly Loaded Aqueous-Fused Silica Slurry” J. Am. Ceram. Soc., 91)2( 640-643 (2008).
17- Q. Huang, P. Chen, M.Gu, Y. Jin, K. Sun, “Effect of surface modification on the rheological behavior of concentrated aqueous SiC suspensions”MaterLett, 56(4) (2002), 546-553.
18- X. Zhu, F. Tang, T. S. Suzuki, and Y. Sakka, “Role of the initial degree of ionization of polyethylenimine in the dispersion of silicon-carbide nano particles”.
J. Am. Ceram. Soc. 2003, 86(1), 189-

_||_