An investigation on the effect of adhesive bonding strength on bending behavior of sandwich panels with Al A356/SiCp composite foam core

Subject Areas : journal of New Materials

Masoud Golestanipour ¹ , Abolfazl Babakhani ² , Seyed Mojtaba Zebarjad ³

1 - Materials Research Group, Iranian Academic Center for Education, Culture and Research (ACECR), Mashhad Branch, Iran
2 - Department of Materials and Metallurgical Engineering, School of Engineering, Ferdowsi University of Mashhad, Mashhad, Iran
3 - Department of Materials and Metallurgical Engineering, Faculty of Engineering, Shiraz University, Shiraz, Iran

Received: 2016-02-03 Accepted : 2017-06-17 Published : 2017-05-22

Keywords: Aluminum Foam, Sandwich Panel, Adhesive bonding, three-point bending test,

Abstract :

    Aluminium and aluminium base composite foam core sandwich panels are good energy absorbers for impact protection applications, such as light-weight structural panels, packing materials and energy absorbing devices. In this study, three-point bending tests were carried out on sandwich structures with Al A356/SiCp composite foam core and Al 1100 aluminium face-sheets and also aluminium composite foam without face-sheets. For bonding of panels, three industrial adhesive with different shear strength were used. Maximum of failure force, absorbed energy, bending behavior, deformation model and adhesive bonding were investigated. Results showed that maximum failure force and absorbed energy of sandwich panels were higher than aluminium composite foam without face-sheets. In addition, for samples with higher strength of adhesive bonding, failure were accrued in foam core rather than bonding interface. Finally, because of constant value of face-sheets thickness and mid-span, bonding strength was effective parameter on deformation model and bending behavior of sandwich panels.

References:

1-M.F. Ashby, A. Evans, N.A. Fleck, L.J. Gibson, J.W. Hutchinson, H.N.G. Wadley, “Metal Foams-A Design Guide”, Butterworth-Heinemann, London, 2000.

2-J. Banhart, “Manufacture, characterization and application of cellular metals and metallic foams”, Progress in Material Science, Vol. 46, pp. 559-632, 2001.

3-H.P. Degischer, B. Kriszt, “Handbook of cellular metals”, Weinheim, Wiley-VCH, 2002.

4-J. Banhart, H.W. Seeliger, “Aluminium Foam Sandwich Panels: Manufacture, Metallurgy and Applications”, Advanced Engineering Materials, Vol. 10, pp. 793-802, 2008.

 

5-W. Hou, F. Zhu, G. Lu, D.N. Fang, “Ballistic impact experiments of metallic sandwich panels with aluminium foam core”, International Journal of Impact Engineering, Vol. 37, pp. 1045-1055, 2010.

6-J. Yu, E. Wang, J. Li and Z. Zheng, “Static and low-velocity impact behavior of sandwich beams with closed-cell aluminum-foam core in three-point bending”, International Journal of Impact Engineering, Vol. 35, pp. 885-894, 2008.

7-V. Crupi, G. Epasto and E. Guglielmino, “Comparison of aluminium sandwiches for lightweight ship structures: Honeycomb vs. foam”, Marine Structures, Vol. 30, pp. 74-96, 2013.

8-Z. Sun, X. Hu, S. Sun and H. Chen, “Energy-absorption enhancement in carbon-fiber aluminum-foam sandwich structures from short aramid-fiber interfacial reinforcement”, Composites Science and Technology, Vol. 77, pp. 14-21, 2013.

9-G. Zu, R. Lu, X. Li, Z.  Zhong, X. Ma, M. Han and G. Yao, “Three-point bending behavior of aluminum foam sandwich with steel panel”, Transactions of Nonferrous Metals Society of China, Vol. 23, pp. 2491-2495, 2013.

10-K. Kabir, T. Vodenitcharova and M. Hoffman, “Response of aluminium foam-cored sandwich panels to bending load”, Composites: Part B, Vol. 64, pp. 24-32, 2014.

11-L. L. Yan, B. Han, B. Yu, C. Q. Chen, Q. C. Zhang and T. J. Lu, “Three-point bending of sandwich beams with aluminum foam-filled corrugated cores”, Materials and Design, Vol. 60, pp. 510-519, 2014.

12-مسعود گلستانی پور، مینو توکلی، سید مجتبی زبرجد، ابوالفضـل باباخـانی، بهـروز نادری "بررسی جذب انرژی پنل­های ساندویچی با هسته فوم آلومینیوم تحت آزمون سوراخ­کاری"، مجله مواد نوین، جلد 3، شماره 2، صفحه 38-25، زمستان 1391.

13-M. Golestanipour, H. Amini Mashhadi, M. S. Abravi, M. Malekjafarian, M. H. Sadeghian, “Manufacturing of Al/SiC_p composite foams using calcium carbonate as foaming agent”, Materials Science and Technology, Vol. 27, pp. 923-927, 2011.

14-ASTM E864 Standard, “Standard practice for surface preparation of aluminum alloys to be adhesively bonded in honeycomb shelter panels”, 2003.

15-ASTM E290 Standard, “Standard test method for Bend Testing of Material for Ductility”, 1997.

16-ASTM D790 Standard, “Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials”, 2003.

17-V. Crupi and R. Montanini, “Aluminium foam sandwiches collapse modes under static and dynamic three-point bending”, International Journal of Impact Engineering, Vol. 34, pp. 509-521, 2007.