A Machine Vision Based Approach for Sag Measurement in Power Lines

Subject Areas : Renewable energy

Mohammad Javad Abdollahifard ¹ , Mohammad Reaz Mehrdad ²

1 - Computer Vision and Remote Sensing Research Lab- Department of Electrical Engineering Department, Tafresh University, Tafresh, Iran
2 - Computer Vision and Remote Sensing Research Lab- Department of Electrical Engineering Department, Tafresh University, Tafresh, Iran

Received: 2022-04-05 Accepted : 2022-06-22 Published : 2023-11-22

Keywords: power line detection, sag measurement, vision-based measurement, surveying,

Abstract :

The supply of permanent electrical energy is of vital importance in modern life and its disruption can cause heavy damage to different areas in industry, commerce, transportation, sanitation and health, education, and management of the society. To prevent the network from short-circuiting to the ground, the amount of sag (drop) of the conductors must be within a standard range. Existing methods for sag measurement often require permanent installation of equipment - such as a camera, GPS receiver, and magnetic field sensor - on the line, the poles/towers, and/or around them. The method presented in this paper performs sag measurement based on a single image recorded from the conductor and poles/tow­ers on its both sides. In addition, the distance between the two ends of the conductor from the camera needs to be measured using a laser rangefinder. First, the position of the two ends of the conductor in three-dimensional space is obtained with the help of rangefinder data. Then, from all the parabolas that pass through these two points, the one that best matches the visual observations and field assumptions is selected, and based on that, the three-dimensional conductor model is generated and the sag is calculated. The proposed measurement method can be done without interruption of the network and dangerous approach to the line and with the help of portable and inexpensive equipment. Evaluation on laboratory and field data showed that the proposed method is not sensitive to the shooting angle, works well in complicated backgrounds, and has an average error of less than 1% of the sag value.

References:

[1] C. Deng, S. Wang, Z. Huang, Z. Tan, J. Liu, "Unmanned aerial vehicles for power line inspection: a
cooperative way in platforms and communications", Journal Commun, vol. 9, no. 9, pp. 687-692, Sept. 2014 (dio:10.12720/jcm.9.9.687-692).

[2] A.T. Zengin, G. Erdemir, T.C. Akinci, S Seker, "Measurement of power line sagging using sensor data of a power line inspection robot", IEEE Access vol. 8 pp. 99198-99204, May. 2020 (doi: 10.1109/ACCE­SS.2­020­.2998154).

[3] D. Xiaoyuan, "Analytic method to calculate and characterize the sag and tension of overhead lines", IEEE Trans. on Power Delivery, vol. 31, no. 5, pp. 2064-2071, Jan. 2016 (doi: 10.1109/TPWRD.2015.2510318).

[4] Y. Du, Y. Liao, "Online estimation of power transmission line parameters, temperature and sag", Proceeding of the IEEE/NAPS, pp. 1-6, American, Aug. 2011 (doi: 10.1109/NAPS.2011.6024854).

[5] R.M. Hayes, A. Nourai, "Power line sag monitor", U.S. Patent, No. 6,205,867. 27 Mar. 2001.

[6] R.G. Olsen, K.S. Edwards, "A new method for real-time monitoring of high-voltage transmission-line conductor sag", IEEE Trans. on Power Delivery, vol. 17 no. 4, pp. 1142-1152, Oct. 2002 (doi: 10.1109/­TPWRD­.2002.804015).

[7] X. Sun, K.S. Lui, K.K.Y. Wong, W.K. Lee, Y. Hou, Q. Huang, P.W.T. Pong, "Novel application of magnetoresistive sensors for high-voltage transmission-line monitoring", IEEE Trans. on Magnetics, vol. 47 no. 10, pp. 2608-2611, Sept. 2011 (doi: 10.1109/TMAG.2011.2158085).

[8] A. Habib, Q. Huang, J. Li, Z. Zhang, "Estimation of current and sag in overhead power transmission lines with optimized magnetic field sensor array placement", IEEE Trans. on Magnetics, vol. 53 no. 5, pp. 1-10, Jan. 2017 (doi: 10.1109/TMAG.2017.2657490).

[9] C. M. Bonsu, U.F. Krekeler, G.T. Heydt, Y. Hoverson, J. Schilleci, B.L. Agrawal, "Application of the global positioning system to the measurement of overhead power transmission conductor sag", IEEE Trans. on Power Delivery, vol. 17, no. 1, pp. 273-278, Jan. 2002 (doi: 10.1109/61.974218).

[10] S.M. Mahajan, U.M. Singareddy, "A real-time conductor sag measurement system using a differential   GPS", IEEE Trans. on Power Delivery, vol. 27 no. 2, pp. 475-480, Feb. 2012 (doi: 10.1109/TP­WRD.20­11.­218­1963).

[11] M. Wydra, P. Kisala, D. Harasim, P. Kacejko, "Overhead transmission line sag estimation using a simple  optomechanical system with chirped fiber bragg gratings, Part 1: Preliminary measurements", Sensors, vol. 18 no. 1, Article Number: 309, Jan. 2018 (doi: 10.3390/s20092652).

[12] G. Sohn, Y. Jwa, H.B. Kim "Automatic powerline scene classification and reconstruction using airborne lidar data", Proceeding of the ISPRS, vol. I-3, pp. 167-172, Aug. 2012 (doi: 10.5194/isprsannals-I-3-167-2012).

[13] J. Oh, C. Lee 2, "3D power line extraction from multiple aerial images", Sensors, vol. 17, no. 10, Article Number: 2244, Sept. 2017 (doi: 10.3390/s17102244).

[14] M. Wydra, P. Kubaczynski, K. Mazur, B. Ksiezopolski, "Time-aware monitoring of overhead transmission line sag and temperature with LoRa communication", Energies, vol. 12, no. 3, Article Number: 505, Feb. 2019 (doi: 10.3390/en12030505).

[15] M.Y. Sermet, I. Demir, S. Kucuksari, "Overhead power line sag monitoring through augmented reality", Proceeding of the IEEE/NAPS, pp. 1-5, American, Sept. 2018 (doi: 10.1109/NAPS.2018.8600565).

[16] M.A. Isa, D. Sims-Waterhouse, S. Piano, R. Leach, "Volumetric error modelling of a stereo vision system for error correction in photogrammetric three-dimensional coordinate metrology", Precision Engineering, vol. 64, pp.188-199, July 2020 (10.1016/j.precisioneng.2020.04.010).

[17] H. Kim, W.Y. Kim, "Automated inspection system for rolling stock brake shoes", IEEE Trans. on Instru­mentation and Measurement, vol. 60, no. 8, pp. 2835-2847, April 2011 (doi: 10.1109/TIM­.2011­.211­911­0).

[18] S. Huang, W. Jin, M. Ye, Z. Liu, B. Yu, Y. Ying, X. Zhang, Y. Mu, "A vision based method for automated measurement of circular fiber cross-sections", Measurement, vol. 162, Article Number: 107913, Oct. 2020 (doi: 10.1016/j.measurement.2020.107913).

[19] M. Alidoust, M. Zeinali, H. Mahdavi-Nasab, "A robust edge detection method with subpixel accuracy in presence of noise", Journal of Intelligent Procedures in Electrical Technology, vol. 6, no. 24, pp. 17-26,  Jan. 2016 (in Persian) (dor: 20.1001.1.23223871.1394.6.24.2.2).

[20] V. Ghods, A. Behrad, "Road extraction and car detection from aerial image using intensity and color", Journal of Intelligent Procedures in Electrical Technology, vol. 2, no. 6, pp. 55-64, Aug. 2011 (in Persian) (dor: 20.1001.1.23223871.1390.2.6.6.2).