Designing Sensorless Drive of BLDC Motor With Using DTC Method

Subject Areas : Electric machine design and control

Gholam Reza Lalehzar ¹ (MSc /Malek Ashtar University of Technology)
Amir Movahedi ² (PhD Condidate /University of Kashan)

Received: 2013-06-01 Accepted : 2013-09-22 Published : 2013-11-01

Keywords: drive, BLDC motor, sensorless, direct torque control method,

Abstract :

In this paper, to estimate the rotor position in sensorless BLDC motor drive, the method of the ratio functions line by line flux is used. This method, compared to other methods which are evaluated to estimate the rotor position, has low software volume and therefore, its implementation is easy and also manufacturing cost is less. Also this method has an appropriate efficiency in a wide range of speed and estimate the rotor position is independent of speed and rotor frequency. Also in this paper, the method Direct Torque Control (DTC) is used to design sensorless BLDC motor drive. DTC method is one of the most innovative and efficient methods in control of the electrical machine. High speed response to changes in torque, simplicity of implementation, independence to machine parameters and needs of less computation are the advantages of this method. At the end of this paper, simulation results by using software MATLAB shows good performance of sensorless BLDC motors with DTC method compared to the switching function method.

References:

[1] J.S. Mayer, O. Wasynczuk, "Analysis and modeling of a single-phase brushless DC motor drive system", IEEE Trans. On Power Systems, Vol. 9, pp. 473-479, Sep. 1989.
[2] M. Gougani, M. Chapariha, J. Jatskevich, A. Davoudi, "Hall sensor-based locking electric differential system for BLDC motor driven electric vehicles", IEEE/IEVC, pp. 1-7, March 2012.
[3] N. Matsui, "Sensorless PM brushless DC motor drives, "IEEE Trans. on Industrial Electronics, Vol. 43, No. 2, pp. 300-308, 1996.
[4] J.P. Johnson, M. Ehsani, Y. Guzelgunler, "Review of sensorless methods for brushless DC", IEEE/IAS, Vol. 1, pp. 143-150, 1999.
[5] Y. Jin Yong, L. Bi Qiang, "Study of position detection method for sensorless brushless DC elect‌ro‌motor", IEEE/ICEMS, Vol. 2, pp. 1218-1222, Aug. 2001.
[6] A. Nair, K. R. Rajagopal, "A novel back-EMF detec‌t‌‌ion scheme basedsensorless control of perma‌n‌ent magnet brushless DC motor drive", IEEE/ICEMS, pp. 978-983, Oct. 2010.
[7] S. Gui-Jia, J. W. Mckeever; "Low cost sensorless control of brushless DC motors with improved speed range", IEEE Trans. on Power Systems,Vol. 19, pp. 296-302, March 2004.
[8] N. Ertugrul, P. Acarnley, "A new algorithm for sens‌o‌r‌less operation of permanent magnet motors", IEEE Trans. on Power Systems, Vol. 30, pp. 126-133, Feb. 1994.
[9] G. Zhou, W. Zhou, Y. Jianping,"Improved sensor‌less brushless DC motor drive", IEEE/PESC, pp. 1353-1357, June 2005.
[10] Y.S. Lai, F.S. Shyu, S.S. Tseng, "New initial position detection technique for three-phase brush‌less DC motor without position and current sensors", IEEE Trans. on Power  Systems, Vol. 39, No. 2, Pp. 485-491, April 2003.
[11] W. Huabin, S. Liang, C. Guo-rong, X. Di-jian, "Initial rotor position estimation of BLDC based on inductance method", IEEE/ICBMEI, Vol. 3, pp. 656-659, May 2011.
[12] B. Terzic, M. Jadric; "Design and implementation of the extended kalman filter for the speed and rotor position estimation of brushless DC motor", IEEE Trans. on Power Systems, Vol. 48, pp. 1065-1073, Dec. 2001.
[13] J.Y. Yen, Y.L. Chen, M. Tomizuka, "Variable sampling rate controller design for brushless DC motor", IEEE/CDC, Vol. 1, pp. 462-467, Dec. 2002.
[14] K. Tae-Hyung, L. Byung-Kuk, M. Ehsani, "Sensorless control of the BLDC motors from near zero to high speed", IEEE Trans. on Power Systems, Vol. 19 , pp. 1635-1645, Nov. 2004.
[15] T.H. Kim, M. Ehsani, "Sensorless control of the BLDC motors from near-zero to high speeds", IEEE Trans. on Power Systems, Vol. 19, No. 6, pp.1635-1645, Nov. 2004.
[16] P.L. Chapman, S.D. Sudhoff, C.A. Whitcomb, "Multiple reference frame analysis of nonsinusoidal brushless DC drives", IEEE Trans. on Power Systems, Vol. 14, pp. 440-446, Sep. 1999.
[17] S.A. Zabalawi, A. Nasiri, "State space modeling and simulation of sensorless control of brushless DC motors using instantaneous rotor position tracking", IEEE/VPPC, pp. 90-94, Sep. 2007.
[18] H.N. Phyu, M.A. Jabbar, L. Zhejie, B. Chao, "Modeling and simulation of brushless permanent magnet DC motor in dynamic conditions by time stepping technique", IEEE/ IEMDC, Vol. 1, pp. 376-381, June 2003.
[19] A.H. Niasar, H. Moghbelli, A. Vahedi, "Modeling, simulation and implementation of four-switch, brushless DC motor drive based on switching functions", IEEE/EURCON, pp. 682-687, May 2009.
[20] A.H. Niasar, H. Moghbelli, A. Vahedi, "A novel position sensorless control of a four-switch, brushless DC motor drive without phase shifter", IEEE Trans. on Power Systems, Vol. 23, pp. 3079-3087, Nov. 2008.
[21] Y. Liu, Z. Q. Zhu, D. Howe, "Direct torque control of  brushless DC drives with reduced torque  rip‌ple", IEEE Trans. on Power Systems, Vol. 41, pp. 599-608, April 2005.
[22] Y. Liu, Z.Q. Zhu, D. Howe, "Commutation torque ripple minimization in direct torque controlled PM brushless DC drives", IEEE Trans. on Power Systems, Vol. 43, pp. 1012-1021, aug. 2007.
[23] S.B. Ozturk, W. C. Alexander, H. A. Toliyat, "Direct torque control of four-switch brushless DC motor with non-sinusoidal back emf", IEEE Trans. on Power Systems, Vol. 25, pp. 263-271, Feb. 2010.
[24] S.B. Ozturk, Oh Yang, H.A. Toliyat, "Power Factor Correction of direct torque controlled brushless DC motor drive", IEEE/IAC, pp. 297-304, Sep. 2007.
[25] F. Parasiliti, R. Petrella, M. Tursini, "Initial rotor position estimation method for PM motors", IEEE Trans. on Power Sys., Vol. 39, pp. 1630-1640, Dec. 2003.
[26] W.J. Lee, S.K. Sul, "A new starting method of BLDC motors without position sensor", IEEE/IAS, Vol. 4, pp. 2397-2402, Oct. 2004.

_||_