Increased Light Absorption in CIGS Solar Cells with Plasmonic Ag Nanostructures to Increase Efficiency
Subject Areas : Renewable energySeyed Mohammad Sadegh Hsheminassab 1 , Mohsen Imanieh 2 , Abbas Kamali 3 , Seyyed ali Emamghorashi 4 , Saeed Hassanhasseini 5
1 - Department of Electrical Engineering- Fasa Branch, Islamic Azad University, Fasa, Iran
2 - Department of Electrical Engineering- Fasa Branch, Islamic Azad University, Fasa, Iran
3 - Department of Electrical Engineering- Fasa Branch, Islamic Azad University, Fasa, Iran
4 - Department of Electrical Engineering- Fasa Branch, Islamic Azad University, Fasa, Iran
5 - Department of Electrical Engineering- Fasa Branch, Islamic Azad University, Fasa, Iran
Keywords: FDTD, plasmonics, CIGS solar cells, Ag nano-particles, nano-particle shapes,
Abstract :
Recently, environmental problems on a global scale has been increased seriously. To overcome these problems, Solar cells is important as an energy source and free from contamination. Due to the increasing use of renewables, the use of solar cells for obtaining energy is growing. The cells convert directly sunlight into electricity by the photovoltaic. Photovoltaic energy research and development is generally done in two areas: cost reduction and increasing efficiency. The efficiency of thin film solar cells canbe increased considerably by coupling the solarcells with plasmonic nanoparticles (NPs). this study investigates, through meticuloussimulations, the effects of plasmonic nanoparticle shapes and size on theimprovement of the energy conversion efficiency of CIGS solar cells. Two different shapes including spheres and cylinders were analyzed in this study.It was revealed that the cylindrical Agnanoparticles, of diameter 50 nm, height 125 nm place on an array with period 215 nm exhibited the most substantialenhancement in the optical absorption and electrical currentgeneration. The conclusion attained in this paper has been made throughoptical and electricalanalysis as well as near field imaging studies.
[1] S. Madanian, S.M.A. Zanjani, “Investigating methods of electronic waste management and recycling of ever-increasing electronic wastes with emphasis on eco-friendly processes”, Journal of Intelligent Procedures in Electrical Technology, vol. 11, no. 41, pp. 61-71, Sprin 2020 (in Persian).
[2] G. Aghajani, D. Mirabbasi, B. Alfi, H. S. Hatami, “Demand side management in a smart micro-grid in the presence of renewable generation and demand response”, Journal of Intelligent Procedures in Electrical Technology, vol. 8, no. 30, pp. 55-70, Summer 2017 (in Persian).
[3] A.I. Hochbaum, P. Yang , “Semiconductor nanowires for energy conversion”, Chemical Reviews, vol. 1, no.110, pp. 527–546, Oct. 2009 (doi: 10.1021/cr900075v).
[4] H. Moradmand Jazi, E. Adib, B. Fani, “Investigation and improvement of high step- up converters for pv module applications”, Journal of Intelligent Procedures in Electrical Technology, vol. 7, no. 28, pp. 35-44, Winter 2017 (in Persian).
[5] W. Yanqi, “Arrays of ZnO Nanowire for Photovoltaic Devices”, Dessertation Submitted for PhD Degree, Department of Physics and Materials Science, City University of Hong Kong, 2009.
[6] M.J. Jeng, Z.Y. Chen, Y.L. Xiao, L.B. Chang, J. Ao, Y. Sun, E. Popko, W. Jacak, L. Chow, “Improving efficiency of multicrystalline Si and CIGS solar cells by incorporating metal nanoparticles”, Materials, vol. 8, no. 10, pp. 6761–6771, Oct. 2015 (doi: 10.3390/ma8105337).
[7] S.C. Chen, Y.J. Chen, W.T. Chen, Y.T. Yen, T.S. Kao, T.Y. Chuang, Y.K. Liao, K.H. Wu, A. Yabushita, T. P. Hiseh, M.D.B. Charlton, D.P. Tsai, H.C. Kuo, Y.L. Chueh, “Toward omnidirectional light absorption by plasmonic effect for high-efficiency flexible nonvacuum Cu(In,Ga)Se2 thin film solar cells”, ACS Nano, vol. 8, no. 9, pp. 9341–9348, Aug. 2014 (doi: 10.1021/nn503320m).
[8] S. Royanian, A. Abdolahzadeh Ziabari, R. Yousefi, “Efficiency enhancement of ultra-thin CIGS solar cells using bandgap grading and embedding Au plasmonic nanoparticles”, Plasmonics, vol. 15, no. 4, pp. 1173-1182, Feb. 2020 (doi: 10.1007/s11468-020-01138-2).
[9] S. Mohammadneghad, A. Bahrami, "Solar cells engineering basics of structures and technologies", 1th Edition, University of Science and Technology Publishing Center, Iran, Tehran, 2012 (in Persian).
[10] S.A. Maier, “Plasmonics: Fundamentals and applications”, Springer, New York, 2007 (doi: 10.1007/978-0-387-37825-1).
[11] K.L. Chopra, P.D. Paulson, V. Dutta, "Thin-film solar cells: An overview", Progress in Photovoltaics, vol. 12, pp. 69-92, March 2004 (doi: org/10.1002/pip.541).
[12] F.J Tsai, J.Y. Wang, J.J. Huang, Y.W. Kiang, C.C. Yang, "Absorption enhancement of an amorphous Si solar cell through surface plasmon induced scattering with metal nanoparticles", Optics Express, vol. 18, no. 52, pp. A207-A220, June 2010 (doi: org/10.1364/OE.18.00A207).
[13] H.A. Atwater, A. Polman, "Plasmonics for improved photovoltaic devices", Nature Materials, vol. 9, no. 3, pp. 205-213, Feb. 2010 (doi: org/10.1038/nmat2629).
[14] S. Pillai, K. Catchpole, T. Trupke, M. Green, "Surface plasmon enhanced silicon solar cells", Journal of Applied Physics, vol. 101, no. 9, Article Number: 093105, May 2007 (doi: org/10.1063/1.2734885).
[15] R.S. Kim, J. Zhu, J.H. Park, L. Li, Z. Yu et al., "E-beam deposited Ag-nanoparticles plasmonic organic solar cell and its absorption enhancement analysis using FDTD-based cylindrical nanoparticle optical model", Optics Express, vol. 20, no. 12, pp. 12649-12657, May 2012 (doi.org/10.1364/OE.20.012649).
[16] C.C. Chao, C.M. Wang, J.Y. Chang, "Spatial distribution of absorption in plasmonic thin film solar cells", Optics Express, vol. 18, no. 11, pp. 11763-11771, May 2010 (doi: org/10.1364/OE.18.011763).
[17] Lumerical Solutions, Inc. http://www.lumerical.com/tcad-products/fdtd/ (Lumerical Solutions, Inc. http://www.lumerical.com/tcadproducts/device/).
[18] E.D. Palik, "Handbook of optical constants of solids", vol. 3, Elsevier Science, Academic Press, New York, 1998.
[19] W. Li, Sh. Xu, Y. Dai, P. Ma, Y. Feng, W. Li, H. Luo, Ch. Yang, "Improvement of the crystallinity and efficiency of wide-gap CIGS thin film solar cells with reduced thickness", Materials Letters, vol. 244, pp. 43–46, June 2019 (doi: org/10.1016/j.matlet.2019.02.031).
[20] M. Amiri, A. Eskandarian, A. Abdolahzadeh Ziabari, "Performance enhancement of ultrathin graded Cu(InGa)Se2 solar cells through modification of the basic structure and adding antireflective layers”, Journal of Photonics for Energy, vol.10, no. 2, Article Number 024504, June 2020 (doi: org/10.1117/1.JPE.10.024504).
_||_[1] S. Madanian, S.M.A. Zanjani, “Investigating methods of electronic waste management and recycling of ever-increasing electronic wastes with emphasis on eco-friendly processes”, Journal of Intelligent Procedures in Electrical Technology, vol. 11, no. 41, pp. 61-71, Sprin 2020 (in Persian).
[2] G. Aghajani, D. Mirabbasi, B. Alfi, H. S. Hatami, “Demand side management in a smart micro-grid in the presence of renewable generation and demand response”, Journal of Intelligent Procedures in Electrical Technology, vol. 8, no. 30, pp. 55-70, Summer 2017 (in Persian).
[3] A.I. Hochbaum, P. Yang , “Semiconductor nanowires for energy conversion”, Chemical Reviews, vol. 1, no.110, pp. 527–546, Oct. 2009 (doi: 10.1021/cr900075v).
[4] H. Moradmand Jazi, E. Adib, B. Fani, “Investigation and improvement of high step- up converters for pv module applications”, Journal of Intelligent Procedures in Electrical Technology, vol. 7, no. 28, pp. 35-44, Winter 2017 (in Persian).
[5] W. Yanqi, “Arrays of ZnO Nanowire for Photovoltaic Devices”, Dessertation Submitted for PhD Degree, Department of Physics and Materials Science, City University of Hong Kong, 2009.
[6] M.J. Jeng, Z.Y. Chen, Y.L. Xiao, L.B. Chang, J. Ao, Y. Sun, E. Popko, W. Jacak, L. Chow, “Improving efficiency of multicrystalline Si and CIGS solar cells by incorporating metal nanoparticles”, Materials, vol. 8, no. 10, pp. 6761–6771, Oct. 2015 (doi: 10.3390/ma8105337).
[7] S.C. Chen, Y.J. Chen, W.T. Chen, Y.T. Yen, T.S. Kao, T.Y. Chuang, Y.K. Liao, K.H. Wu, A. Yabushita, T. P. Hiseh, M.D.B. Charlton, D.P. Tsai, H.C. Kuo, Y.L. Chueh, “Toward omnidirectional light absorption by plasmonic effect for high-efficiency flexible nonvacuum Cu(In,Ga)Se2 thin film solar cells”, ACS Nano, vol. 8, no. 9, pp. 9341–9348, Aug. 2014 (doi: 10.1021/nn503320m).
[8] S. Royanian, A. Abdolahzadeh Ziabari, R. Yousefi, “Efficiency enhancement of ultra-thin CIGS solar cells using bandgap grading and embedding Au plasmonic nanoparticles”, Plasmonics, vol. 15, no. 4, pp. 1173-1182, Feb. 2020 (doi: 10.1007/s11468-020-01138-2).
[9] S. Mohammadneghad, A. Bahrami, "Solar cells engineering basics of structures and technologies", 1th Edition, University of Science and Technology Publishing Center, Iran, Tehran, 2012 (in Persian).
[10] S.A. Maier, “Plasmonics: Fundamentals and applications”, Springer, New York, 2007 (doi: 10.1007/978-0-387-37825-1).
[11] K.L. Chopra, P.D. Paulson, V. Dutta, "Thin-film solar cells: An overview", Progress in Photovoltaics, vol. 12, pp. 69-92, March 2004 (doi: org/10.1002/pip.541).
[12] F.J Tsai, J.Y. Wang, J.J. Huang, Y.W. Kiang, C.C. Yang, "Absorption enhancement of an amorphous Si solar cell through surface plasmon induced scattering with metal nanoparticles", Optics Express, vol. 18, no. 52, pp. A207-A220, June 2010 (doi: org/10.1364/OE.18.00A207).
[13] H.A. Atwater, A. Polman, "Plasmonics for improved photovoltaic devices", Nature Materials, vol. 9, no. 3, pp. 205-213, Feb. 2010 (doi: org/10.1038/nmat2629).
[14] S. Pillai, K. Catchpole, T. Trupke, M. Green, "Surface plasmon enhanced silicon solar cells", Journal of Applied Physics, vol. 101, no. 9, Article Number: 093105, May 2007 (doi: org/10.1063/1.2734885).
[15] R.S. Kim, J. Zhu, J.H. Park, L. Li, Z. Yu et al., "E-beam deposited Ag-nanoparticles plasmonic organic solar cell and its absorption enhancement analysis using FDTD-based cylindrical nanoparticle optical model", Optics Express, vol. 20, no. 12, pp. 12649-12657, May 2012 (doi.org/10.1364/OE.20.012649).
[16] C.C. Chao, C.M. Wang, J.Y. Chang, "Spatial distribution of absorption in plasmonic thin film solar cells", Optics Express, vol. 18, no. 11, pp. 11763-11771, May 2010 (doi: org/10.1364/OE.18.011763).
[17] Lumerical Solutions, Inc. http://www.lumerical.com/tcad-products/fdtd/ (Lumerical Solutions, Inc. http://www.lumerical.com/tcadproducts/device/).
[18] E.D. Palik, "Handbook of optical constants of solids", vol. 3, Elsevier Science, Academic Press, New York, 1998.
[19] W. Li, Sh. Xu, Y. Dai, P. Ma, Y. Feng, W. Li, H. Luo, Ch. Yang, "Improvement of the crystallinity and efficiency of wide-gap CIGS thin film solar cells with reduced thickness", Materials Letters, vol. 244, pp. 43–46, June 2019 (doi: org/10.1016/j.matlet.2019.02.031).
[20] M. Amiri, A. Eskandarian, A. Abdolahzadeh Ziabari, "Performance enhancement of ultrathin graded Cu(InGa)Se2 solar cells through modification of the basic structure and adding antireflective layers”, Journal of Photonics for Energy, vol.10, no. 2, Article Number 024504, June 2020 (doi: org/10.1117/1.JPE.10.024504).