Subject Areas : Mechanical Engineering

seyyed rahim hosseini ¹ , Seyyed Masoud Seyyedi ² , Mehdi Hashemi Tilenoee ³

1 - Department of Mechanical Engineering, Aliabad Katoul Branch, Islamic Azad University, Aliabad Katoul, Iran
2 - Department of Mechanical Engineering, Aliabad Katoul Branch, Islamic Azad University, Aliabad Katoul , Iran
3 - Department of Mechanical Engineering, Aliabad katoul Branch, Islamic Azad University, Aliabad Katoul, Iran

Received: 2022-08-09 Accepted : 2022-12-13 Published : 2022-12-01

Keywords:

References:

[1] Zhnegguo, Zhang, Xu Tao, and Fang Xiaoming. "Experimental study on heat transfer enhancement of a helically baffled heat exchanger combined with three-dimensional finned tubes." Applied Thermal Engineering 24, no. 14-15 (2004): 2293-2300.

[2] Neshumayev, Dmitri, ArvoOts, Jaan Laid, and Toomas Tiikma. "Experimental investigation of various turbulator inserts in gas-heated channels." Experimental Thermal and Fluid Science 28, no. 8 (2004): 877-886.

[3] Yakut, Kenan, and Bayram Sahin. "Flow-induced vibration analysis of conical rings used for heat transfer enhancement in heat exchangers." Applied Energy 78, no. 3 (2004): 273-288.

[4] Yildiz, Cengiz, Yaşar Biçer, and Dursun Pehlivan. "Effect of twisted strips on heat transfer and pressure drop in heat exchangers." Energy Conversion and Management 39, no. 3-4 (1998): 331-336.

[5] Durmuş, Aydın. "Heat transfer and exergy loss in cut out conical turbulators." Energy Conversion and Management 45, no. 5 (2004): 785-796.

[6] Eiamsa-ard, Smith, and PongjetPromvonge. "Enhancement of heat transfer in a tube with regularly-spaced helical tape swirl generators." Solar energy 78, no. 4 (2005): 483-494.

[7] Kurtbaş, İ., Durmuş, A., Eren, H. and Turgut, E., 2007. Effect of propeller type swirl generators on the entropy generation and efficiency of heat exchangers. International Journal of Thermal Sciences, 46(3), pp.300-307.

[8] Gül, H. and Evin, D., 2007. Heat transfer enhancement in circular tubes using helical swirl generator insert at the entrance. International Journal of Thermal Sciences, 46(12), pp.1297-1303.

[9] Zamankhan, P., 2010. Heat transfer in counterflow heat exchangers with helical turbulators. Communications in Nonlinear Science and Numerical Simulation, 15(10), pp.2894-2907.

[10] Eiamsa-ard, S., Pethkool, S., Thianpong, C. and Promvonge, P., 2008. Turbulent flow heat transfer and pressure loss in a double pipe heat exchanger with louvered strip inserts. International Communications in Heat and Mass Transfer, 35(2), pp.120-129.

[11] Naphon, P. and Suchana, T., 2011. Heat transfer enhancement and pressure drop of the horizontal concentric tube with twisted wires brush inserts. International Communications in Heat and Mass Transfer, 38(2), pp.236-241.

[12] Turgut, E., Çakmak, G. and Yıldız, C., 2012. Optimization of the concentric heat exchanger with injector turbulators by Taguchi method. Energy conversion and management, 53(1), pp.268-275.

[13] Şahin, H.M., Baysal, E. and Dal, A.R., 2013. Experimental and numerical investigation of thermal characteristics of a novel concentric type tube heat exchanger with turbulators. International journal of energy research, 37(9), pp.1088-1102.

[14] Şahin, H.M., Baysal, E., Dal, A.R. and Şahin, N., 2015. Investigation of heat transfer enhancement in a new type heat exchanger using solar parabolic trough systems. International journal of hydrogen energy, 40(44), pp.15254-15266.

[15] HashemiKarouei, S.H. and Mousavi Ajarostaghi, S.S., 2021. Influence of a curved conical turbulator on heat transfer augmentation in a helical double‐pipe heat exchanger. Heat Transfer, 50(2), pp.1872-1894.

[16] Yadav, R.K. and Singhai, A., 2020. Heat Transfer Enhancement in a Double Pipe Heat Exchanger using Bio-Nano fluid (Mango-Bark) using CFD. International Journal of Innovative Research in Technology, 6(9), 123-130.