The Improvement of Mechanical Properties of the Incoloy 825 Weld Metal by Applying Electromagnetic Vibration

Subject Areas : Welding

Ali Pourjafar ¹ , Reza Dehmolaei ²

1 - Department of Materials Science and Engineering, Faculty of Engineering, Shahid Chamran University of Ahvaz, Ahvaz, Iran
2 - Department of Materials Science and Engineering, Faculty of Engineering, Shahid Chamran University of Ahvaz, Ahvaz, Iran; Steel Research Center, Shahid Chamran University of Ahvaz, Ahvaz, Iran

Received: 2020-08-04 Accepted : 2020-08-30 Published : 2021-05-01

Keywords:

References:

[1] E. B. Howard and L. G. Timoty, Desk Edition, Metals Handbook, ASM International, United States of America,1985.

[2] E.F. Bradly, Superalloys A Technical Guide, 2nd Edition, ASM International, Metalspark, OH44073, 1988.

[3] M.J. Donachie, S.J. Donachie, Superalloys: a technical guide, 2nd Edition, ASM International, 2002.

[4] J. R. Davis et al, ASM Specialty Handbook: Nickel, Cobalt, and Their Alloys, Printed in the United States of America, 2000.

[5] R. Coppola, S. R. Fiorentin, Study of γ′-precipitation kinetics in alloy 800 at 575° C by small angle neutron scattering. Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms, 22, 4, 564-572, 1987.‏

[6] J. C. Lippold, Investigation of Weld Cracking in Alloy 800, Welding Journal, 63, 3, 91-103, 1984.

[7] R. S. Dutta, R. Purandare, A. Lobo and S. K. Kulkarni, "Microstructural Aspects of the Corrosion of Alloy 800”, Corrosion Science, 46, 2937–2953, 2004.

[8] K. Balasubramanian, S. Raghavendran1 and V. Balusamy., Studies on the effect of mechanical vibration on the microstructure of the weld metal. International Journal of technology and Engineering Systems, 2, 3,253-256, 2011.

[9] S. Kou, Welding metallurgy, second ed. Hoboken, John Wiley & Sons Inc, 2003.

[10] R. Dehmolaei, M. Shamaniana, A. Kermanpur. Effect of electromagnetic vibration on the unmixed zoneformation in 25Cr–35Ni heat resistant steel/Alloy 800dissimilarwelds, Materials Characterization, 59, 12, 1814-1817, 2008.

[11] A. Abugh, I. K., Kuncy., Microstructure and Mechanical Properties of Vibrated Castings and Weldments: A Review, Journal of Engineering Studies and Research 19(1) ,7, 2013.‏

[12] M. A. G. Dezfuli, Dehmolaei, R., & Zaree, S. R. A. (2019). Microstructural Aspects of 304 Stainless Steel Weld Joints with the Simultaneous Application of Electromagnetic Vibration., Metallography, Microstructure, and Analysis, 8(2), 226-232.

[13] M. Nabahat, Ahmadpour, K., & Saeid, T. (2018). Effect of ultrasonic vibrations in TIG welded AISI 321 stainless steel: microstructure and mechanical properties. Materials Research Express, 5(9), 096509.

[14] P. Singh, Patel, D., & Prasad, S. B. (2017). Investigation on the effect of vibrations on cooling behavior and mechanical properties of SMAW butt welded joints. Sci. Bull. Ser. D, 79.

[15] A. V. D. Queiroz, Fernandes, M. T., Silva, L., Demarque, R., Xavier, C. R., & Castro, J. A. D. (2020). Effects of an external magnetic field on the microstructural and mechanical properties of the fusion zone in TIG welding. Metals, 10(6), 714.

[16] P. Sakthivel, & Sivakumar, P. (2014). Effect of vibration in Tig and arc welding using AISI 316 stainless steel. International Journal of Engineering, Research and Science & Technology, 3(4), 116-130.

[17] Y. Sharir, Pelleg, J., & Grill, A. (1978). Effect of arc vibration and current pulses on microstructure and mechanical properties of TIG tantalum welds. Metals Technology, 5(1), 190-196

[18] R. Dehmolaei, M. Shamaniana, A. Kermanpur, Microstructural characterization of dissimilar weld between alloy 800 and HP heat resistant steel,59,10, 1447-1454, 2008.

[19] D.Y. Seo, J. Tsang1, R. Kearsey, W.J. Yang2, K.S. Cho, J.H. Lee, and P. Au1, Crack Growth Rate Behaviour and Microstructural Features of Incoloy 800H under Fatigue and Creep-fatigue Conditions, In ICF12, Ottawa 2009.‏

[20] M. Sireesha, V. Shankar, SK. Albert, S. Sundaresan, Microstructural features of dissimilar welds between 316LNaustenitic stainless steel and Alloy 800, Mater Sci Eng A, 292:74–82, 2000.

[21] L. Sundar and D. R. G. Achar, Review of Weld Cracking in Alloy 800, Indian Welding Journal., 16, 3, 81-86, 1984.

[22] R. Dehmolaei, M. Shamaniana, A. Kermanpur, Microstructural changes, and mechanical properties of Incoloy 800 after 15 years’ service, Materials Characterization 60, 3, 246-250, 2009.

[23] C.C. Hsieh, P.S. Wang, J.S. Wang, W. Wu. Evolution of microstructure and residual stress under various vibration modes in 304 stainless steel welds. The Scientific World Journal. 2014 Jan 1;2014.

[24] S. P. Tewari, Influence of Longitudinal Oscillation on Tensile Properties of Medium Carbon Steel Welds of Different Thickness, Science & Technology Asia 14, 4, 17-27, 2009.

[25] Y. G. Zhao, Y. H. Liang, Q. D. Qin, W. Zhou and Q. C. Jiang, Effect of Mechanical Vibration on the Microstructure, Impact Toughness and Thermal Fatigue Behavior of Cast Hot Working Die Steel, ISIJ international 44 (7), 1167-1172, 2004.

[26] J. Prakash, S.P. Tewari, B.K. Srivastava, Nucleation, grain growth, solidification and residual stress relaxation under stationary and vibratory welding condition—A review. Int. J. Engg. Techsci. 1, 1, 2010.

[27] C. Zhang, M. WU, J. DU, Improving Weld Quality by Arc-Excited Ultrasonic Treatment, Tsinghua Science and Technology, 6, 5, 475-478, 2001.

[28] B. Pucko, V. Gliha., Charpy toughness of vibrated microstructures. Metalurgija., 44, 2, 103-106, 2005.

[29] S. Kou, Y. Le., Improving weld quality by low frequency arc oscillation., Welding Journal 64, 3, 51-55, 1985.

[30] D. Facchini, (2012). Biomedical nanocrystalline metals and alloys: Structure, properties and applications. In Nanomedicine (pp. 36-67). Woodhead Publishing.‏

[31] Y. Mizutani; Y. Ohura, K. Miwa., Effect of the Electromagnetic Vibration Intensity on Microstructural Refinement of Al-7%Si Alloy., Materials Transactions, 45, 6, 2004.

[32] T.Y. Kuo, H.T. Lee, Effects of filler metal composition on joining properties of alloy 690 weldments, Materials Science and Engineering A, 338,202-212, 2002