Thermo-Mechanical Analysis of Wire Drawing of Copper with PCD die: FEM Study

Subject Areas : Finite Element Modeling

Mohammad Soroush Merkani ¹ , Ghader Faraji ²

1 - Department of Mechanical Engineering, University of Tehran, Tehran, Iran.
2 - Department of Mechanical Engineering, University of Tehran, Tehran, Iran.

Received: 2022-03-27 Accepted : 2022-06-13 Published : 2022-07-01

Keywords:

References:

[1] Wistreich, J. G. (1955). Investigation of the mechanics of wire drawing. Proceedings of the Institution of Mechanical Engineers, 169(1), 654-678.

[2] Siebel, E. (1947). Der derzeitige Stand der Erkenntnisse über die mechanischen Vorgänge beim Drahtziehen. Verlag Stahleisen.

[3] Sachs G. Plasticity problems in metals. Trans Faraday Soc 1928; 24:84–92.

[4] Yang, C. T. (1961). On the mechanics of wire drawing.

[5] Avitzur, B. (1968). METAL FORMING. PROCESSES AND ANALYSIS. MCGRAW-HILL, INC., NEW YORK. 1968, 500 P.

[6] Zimerman, Z., & Avitzur, B. (1970). Metal flow through conical converging dies—a lower upper bound approach using generalized boundaries of the plastic zone.

[7] Avitzur, B. (1971). Study of flow through conical converging dies. In Metal forming: Interrelation between theory and practice (pp. 1-46). Springer, Boston, MA.

[8] Li, Y., Quick, N. R., & Kar, A. (2002). Thermo-mechanical effects in laser microprocessing for dieless metal wire drawing. Journal of Laser Applications, 14(2), 91-99.

[9] Christopherson, D. G., & Naylor, H. (1955). Promotion of fluid lubrication in wire drawing. Proceedings of the Institution of Mechanical Engineers, 169(1), 643-653.

[10] Haddi, A., Imad, A., & Vega, G. (2011). Analysis of temperature and speed effects on the drawing stress for improving the wire drawing process. Materials & Design, 32(8-9), 4310-4315.

[11] Haddi, A., Imad, A., & Vega, G. (2012). The influence of the drawing parameters and temperature rise on the prediction of chevron crack formation in wire drawing. International journal of fracture, 176(2), 171-180.

[12] Vega, G., Haddi, A., & Imad, A. (2009). Temperature effects on wire-drawing process: experimental investigation. International Journal of Material Forming, 2(1), 229-232.

[13] Sas-Boca, I. M., Tintelecan, M., Pop, M., Iluţiu-Varvara, D. A., & Mihu, A. M. (2017). The wire drawing process simulation and the optimization of geometry dies. Procedia Engineering, 181, 187-192.

[14] Jokovic, Z., & Djapic, N. (2015). Optimization of a cold wire drawing technological process. Journal of Chemical Technology and Metallurgy, 50(5), 653-660.

[15] Vega, G., Haddi, A., & Imad, A. (2009). Investigation of process parameters effect on the copper-wire drawing. Materials & Design, 30(8), 3308-3312.

[16] Baumann, M., Selbmann, R., Milbrandt, M., Kräusel, V., & Bergmann, M. (2021). Adjusting the Residual Stress State in Wire Drawing Products via In-Process Modification of Tool Geometries. Materials, 14(9), 2157.

[17] El-Domiaty, A., & Kassab, S. Z. (1998). Temperature rise in wire-drawing. Journal of Materials Processing Technology, 83(1-3), 72-83.

[18] Geleji, S. (1960). Bildsame formung der metalle in rechnung und versuch. Akademie-Verlag.

[19] Jo, H. H., Lee, S. K., Kim, M. A., & Kim, B. M. (2002). Pass schedule design system in the dry wire-drawing process of high carbon steel. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 216(3), 365-373.

[20] Lee, S. K., Ko, D. C., & Kim, B. M. (2009). Pass schedule of wire drawing process to prevent delamination for high strength steel cord wire. Materials & Design, 30(8), 2919-2927.

[21] Celentano, D. J. (2010). Thermomechanical simulation and experimental validation of wire drawing processes. Materials and Manufacturing Processes, 25(7), 546-556.

[22] Akter, S., & Hashmi, M. S. J. (2006). Wire drawing and coating using a combined geometry hydrodynamic unit: Theory and experiment. Journal of materials processing technology, 178(1-3), 98-110.

[23] Tiernanan, P., & Hillery, M. T. (2004). Dieless wire drawing—an experimental and numerical analysis. ournal of Materials Processing Technology, 155, 1178-1183.

[24] Mohammed, R. J., Ali, J. K., & Nassar, A. A. (2019). Numerical analysis of continuous dieless wire drawing process. International Journal of Engineering & Technology, 8(1.5), 248-256.

[25] Kolev, Z. D., & Kadirova, S. Y. (2019, September). Numerical modelling of heat transfer in convector’s pipes by ABAQUS. In IOP Conference Series: Materials Science and Engineering (Vol. 595, No. 1, p. 012006). IOP Publishing.

[26] Masumi, A. A., Rahimi, G. H., & Liaghat, G. H. (2018). The use of the layerwise theory in heat transfer analysis of metal composite vessel by DQM. International Journal of Thermal Sciences, 132, 14-25.

[27] Khadivipanah, P., Pintado, X., Olivella, S., & Vaunat, J. (2020). Copper canister shearing in spent nuclear fuel repository using Bodner–Partom model. Geomechanics for Energy and the Environment, 22, 100171.

[28] Girard, G., Frydrych, K., Kowalczyk-Gajewska, K., Martiny, M., & Mercier, S. (2021). Cyclic response of electrodeposited copper films. Experiments and elastic–viscoplastic mean-field modeling. Mechanics of Materials, 153, 103685.

[29] Haddi, A., Imad, A., & Vega, G. (2012). On the analysis of die wear in wire-drawing process. Tribology transactions, 55(4), 466-472.