Analytical and Numerical Evaluation of Wire Flat Rolling Process Based on the Slab Method and DEFORM-3D

Subject Areas : Manufacturing & Production

Behzad Pasoudeh ¹ , Hadi tagimalek ²

1 - PhD Student, Department of Engineering, Mechanical group, Urmia University, Urmia, Iran
2 - PhD Student, Faculty of Mechanical Engineering, Semnan University, Semnan, Iran

Received: 2020-02-23 Accepted : 2020-07-10 Published : 2020-11-01

Keywords:

References:

[1]               H. Tagimalek, M. Azargoman, M.R. Maraki, M. Mahmoodi, “The effects of diffusion depth and heat-affected zone in NE-GMAW process on SUH 310S steel using an image processing method”, Inter Jour of Iron & Steel Society of Iran., Vol. 17, Issue. 1, No. 1, 2020, pp. 11-20.

[2]               M. Kazeminezhad, A. Karimi Taheri, “A theoretical and experimental investigation on wire flat rolling process using deformation pattern”, J. Mater. Des., Vol. 26, 2008, pp. 99–103.

[3]               B. Pasoodeh, A. Parvizi, H. Akbari, “Effects of asymmetrical rolling process on the micro hardness and microstructure of brass wire”, JCAMECH., Vol. 49, 2018, pp. 143-148.

[4]               B. Pasoodeh, A. Parvizi, H. Akbari, “Investigation of microstructure and mechanical properties in asymmetrically rolled copper wire”, Journal of the Brazilian Society of Mechanical Science and Engineering., Vol. 30(30), 2017, pp. 5109-5116.  

[5]               A. Parvizi, B. Pasoodeh, K.Abrinia, H. Akbari, “Analysis of curvature and width of the contact area in asymmetrical rolling of wire”, Journal of Manufacturing Process., Vol. 20, 2017, pp. 245-249.

[6]               M. Kazeminezhad, A. Karimi Taheri, “An experimental investigation on the deformation behavior during wire flat rolling process”, J. Mater. Process. Technol., Vol. 160, 2005, pp. 313-320.

[7]               M. Kazeminezhad, A. Karimi Taheri, “Deformation inhomogeneity in flattened copper wire”, J. Mater. Des., Vol. 28, 2007, pp. 2047-2053.

[8]               PP. Gudur, M. Salunkhe, U.S. Dixit, “A theoretical study on the application of asymmetric rolling for the estimation of friction”, Int. J. Mech. Sci., Vol. 50, 2008, pp. 315-327.

[9]               T. Yong, G. Yan-hui, ZD. Wang, GD. Wang, “Analysis of rolling pressure in asymmetrical rolling process by slab method”, J. Iron. Steel. Res. Int., Vol. 16(4), 2009, pp. 22-26.

[10]           D. Kumar, U.S. Dixit, “A slab method study of strain hardening and friction effects in cold foil rolling process”, J. Mater. Process. Technol., Vol. 171, 2006, pp. 331-340.

[11]           S. Chen, H. Liu, Y. Peng, J. Sun, “Slab analysis of large cylindrical shell rolling considering mixed friction”, Int. J. Mech. Sci. Technol., Vol. 30, 2014, pp. 4753-4760.

[12]           M. Qwamizadeh, M. Kadkhodaei, M. Salimi, “Asymmetrical rolling analysis of bonded two-layer sheets and evaluation of outgoing curvature”, Int. J. Adv. Manuf. Technol., Vol. 73, 2014, pp. 521-533.

[13]           S.H. Zhang, D.W. Zhao, C.R. Gao, G.D. Wang, “Analysis of asymmetrical sheet rolling by slab method”, Int. J. Mech. Sci., Vol. 65, 2012, pp. 168-176.

[14]           F. Afrouz, A. Parvizi, “An analytical model of asymmetric rolling of unbounded clad sheets with shear effects”, Journal of Manuf Process., Vol. 20, 2016, pp. 162-171.

[15]           G.Y. Tzou, M.N. Hang, “Study on minimum thickness for asymmetrical hot-and-cold PV rolling of sheet considering constant shear friction”, J. Mater. Process. Technol., Vol. 119(3), 2001, pp. 229-233.

[16]           G.Y. Tzou, “Relationship between frictional coefficient and frictional factor in asymmetrical sheet rolling”, J. Mater. Process. Technol., Vol. 86, 1999, pp. 271-277.

[17]           R, Iankov, “Finite element simulation of profile rolling wire”, J. Mater. Process. Technol., Vol.142, 2003, pp. 355-361.

[18]           A. Parvizi, B. Pasoodeh, K. Abrinia, H. Akbari, “Analysis of curvature and width of the contact area in asymmetrical rolling of wire”, Journal of Manufacturing Processes., Vol. 20, 2015, pp. 245-249.

[19]           S.P. Hamidpour, A. Parvizi, A. Seyyed Nosrati, “Upper bound analysis of wire flat rolling with experimental and FEM verification”, Meccanica., Vol. 54, 2019, pp. 2247-2261.

[20]           M. Kazeminezhad, A. Karimi Taheri, “Calculation of rolling pressure distribution and force in wire flat rolling process”, J. Mater. Process. Technol., Vol. 171, 2006, pp. 253-258.

[21]           A. Parvizi, B. Pasoodeh, K. Abrinia, “An analytical approach to asymmetrical wire rolling process with finite element verification”, Int. J. Adv. Manuf. Technol., Vol. 82, 2015, pp. 1-9.