Modeling and production of high strength Al strips by equal channel multi angular pressing method

Subject Areas : Chemistry

Peyman Keshtiban ¹ , Mohammad Zadshakouyan ² , Ghader Faraji ³

1 - Department of Mechanical Engineering, University of Tabriz, Tabriz, Iran
2 - Department of Mechanical Engineering, University of Tabriz, Tabriz, Iran
3 - Department of Mechanical Engineering, University College of Engineering, University of Tehran, Tehran 11155-4563, Iran

Received: 2015-08-02 Accepted : 2015-11-02 Published : 2015-12-01

Keywords:

References:

References

[1] S. Arab, A. Akbarzadeh, "The effect of equal channel angular pressing process on the microstructure of az31 mg alloy strip shaped specimens", J. Magnesium Alloys, Vol. 1, No. 2, 2013, pp. 145-149.

[2] J.Y. Park, D.N. Lee, "Deformation and annealing textures of equal-channel angular pressed 1050 al alloy strips", Mater. Sci. Eng., A, Vol. 497, No. 1, 2008, pp. 395-407.

[3] K. Nakashima, Z. Horita, M. Nemoto, T.G. Langdon, "Development of a multi-pass facility for equal-channel angular pressing to high total strains", Mater. Sci. Eng., A, Vol. 281, No. 1, 2000, pp. 82-87.

[4] H.S. Kim, "Finite element analysis of deformation behaviour of metals during equal channel multi-angular pressing", Mater. Sci. Eng., A, Vol. 328, No. 1, 2002, pp. 317-323.

[5] J. Jung, S.C. Yoon, H.-J. Jun, H.S. Kim, "Finite element analysis of deformation homogeneity during continuous and batch type equal channel angular pressing", J. Mater. Eng. Perform., Vol. 22, No. 11, 2013, pp. 3222-3227.

[6] G. Faraji, A. Babaei, M.M. Mashhadi, K. Abrinia, "Parallel tubular channel angular pressing (ptcap) as a new severe plastic deformation method for cylindrical tubes", Mater. Lett., Vol. 77, No.  2012, pp. 82-85.

[7] G. Faraji, M. Mousavi Mashhadia, "Plastic deformation analysis in parallel tubular channel angular pressing (ptcap)", J. Adv. Mater. Pro., Vol. 1, No. 4, 2013, pp. 23-32.

[8] G. Faraji, M.M. Mashhadi, S.-H. Joo, H.S. Kim, "The role of friction in tubular channel angular pressing", Rev. Adv. Mater. Sci, Vol. 31, No.  2012, pp. 12-18.

[9] G. Faraji, M. Mashhadi, A. Dizadji, M. Hamdi, "A numerical and experimental study on tubular channel angular pressing (tcap) process", J. Mech. Sci. Technol., Vol. 26, No. 11, 2012, pp. 3463-3468.

[10] G. Faraji, P. Yavari, S. Aghdamifar, M.M. Mashhadi, "Mechanical and microstructural properties of ultra-fine grained az91 magnesium alloy tubes processed via multi pass tubular channel angular pressing (tcap)", J. Mater. Sci. Technol., Vol. 30, No. 2, 2014, pp. 134-138.

[11] F. Fereshteh-Saniee, M. Asgari, M. Barati, S.M. Pezeshki, "Effects of die geometry on non-equal channel lateral extrusion (necle) of az80 magnesium alloy", TTrans. Nonferrous Met. Soc. China, Vol. 24, No. 10, 2014, pp. 3274-3284.

[12] A. Shokuhfar, O. Nejadseyfi, "The influence of friction on the processing of ultrafine-grained/nanostructured materials by equal-channel angular pressing", J. Mater. Eng. Perform., Vol. 23, No. 3, 2014, pp. 1038-1048.

[13] Y. Iwahashi, Z. Horita, M. Nemoto, T.G. Langdon, "An investigation of microstructural evolution during equal-channel angular pressing", Acta Mater., Vol. 45, No. 11, 1997, pp. 4733-4741.

[14] N. El Mahallawy, F.A. Shehata, M.A. El Hameed, M.I.A. El Aal, H.S. Kim, "3d fem simulations for the homogeneity of plastic deformation in al–cu alloys during ecap", Mater. Sci. Eng., A, Vol. 527, No. 6, 2010, pp. 1404-1410.

[15] R. Smerd, S. Winkler, C. Salisbury, M. Worswick, D. Lloyd, M. Finn, "High strain rate tensile testing of automotive aluminum alloy sheet", Int. J. Impact Eng., Vol. 32, No. 1, 2005, pp. 541-560.