The Weldability Evaluation of Dissimilar Welds of AISI 347 Stainless Steel to ASTM A335 Low Alloy Steel by Gastungesten Arc Welding

Subject Areas : Chemistry

Iman Hajiannia ¹ , Morteza Shamanian ² , Masoud Kasiri ³

1 - Department of Materials Engineering, Najafabad Branch, Islamic Azad University, Isfahan, Iran.
2 - Department of Materials Engineering, Isfahan University of Technology, Isfahan, Iran
3 - Department of Materials Engineering, Najafabad Branch, Islamic Azad University, Isfahan, Iran.

Received: 2013-08-27 Accepted : 2013-12-01 Published : 2013-10-01

Keywords:

References:

1. H. ShahHosseini, M. Shamanian, A. Kermanpur, “Characterization of microstructures and mechanical properties of Inconel 617/310 stainless steel dissimilar welds”, Mater Charact, vol. 62, 2011, pp.425-431.


2. ASM Handbook, Volume 1, “Properties and Selection: Irons, Steels, and High Performance Alloys”, ASM International, Materials Park, Ohio, 2002.


3. J. C. Lippold, D. Koteki, “Welding Metallurgy and Weldability of Stainles Steels”, John Wiley and Sons, New Jersey, 2005.


4. N. Arivazhagan, S. SurendraSingh, “Investigation on AISI 304 Austenitic Stainless Steel to AISI 4140 Low Alloy Steel Dissimilar Joints by Gas Tungsten Arc, Electron Beam and Friction Welding”, Mater Des, vol. 32, 2011, pp. 3036–3050.


5. R. L. Klueh, L. King, “Austenitict Stainless Steel-Ferritic Steel Weld Joint Failures”, Weld J, Vol. 61, 1982, pp. 302-311.


6. H. Muesch, “Welding of material grade TP 347”, Nucl Eng Des, vol. 2, 2003, pp. 85:155-161.


7. G. Kaishu, X. Xiaodong, X. Hong, W. Zhiwen, “Effect of aging at 700 °c on precipitation and toughness of AISI 321 and AISI 347 austenitic stainless steel welds”, Nucl Eng Des, vol. 23, 2005, pp. 2485–2494.


8. M. Tan, E. Akiyama, H. Habazaki, A. Kawashima, “The role of chromium and molybdenum in passivation of amorphous Fe-Cr-Mo-P-C alloys in deaerated 1 M HCl”, Corros Sci, vol. 38, 1996, pp.
   2137-2151.


9. V. Kumslyts, A. Vaclovas, “The Influence of Temperature-Time Parameter of Welded Joints Thermal Treatment on Strength-Related Characteristics Chromium-Molybdenum and Low Alloy Manganese Steels”, Mat Science, vol. 13, 2007, pp. 123-126.


10. R. Dehmolaie, M. Shamanian, A. Kermanpour, “Microstructural characterization of dissimilar welds alloy 800 and HP heat – resistant steel”, Mater Charact, vol. 59, 2008, pp. 1447-54.


11. H. Naffakh, M. Shamanian, F. Ashrafizadeh, “Dissimilar Welding of AISI 310 Austenitic Stainless Steel to Nickel-Based Alloy Inconel 657”, J Mater Process Technol, vol. 209, 2008, 3628-3639.


12. M. Shimada, “intergranular corrosion resistant 304 stainless steel by twin-induced grain boundary engineering”, Acta Mater, vol. 50, 2003, pp.2331-2341.


13. ASME Sec II, “Specification for Welding Rods, Electrodes and Filler Metals, Part C”, American Society of Mechanical Engineers, 3^rd ed., 2004.


14. L. LI, R. MESSLER, “Segregation of Phosphorus and Sulfur in Heat-Affected Zone Hot Cracking of Type 308 Stainless Steel”, Weld J, 2002, pp. 78-84.


15. I. Haroe, A. Rosen, I. Hall, “Evolution of microstructure of AISI 347 stainless steel during heat treatment”, MSTec, vol. 9, 1993, pp. 620-626.


16. A. L. Schaeffler, “Selection of Austenitic Electrodes for Welding Dissimilar Metals”, Weld J, 1947, pp. 601-620.


17. ASME Sec IX, “Qualification Standard for Welding and Brazing Procedure”, Article II, Welding Procedure Qualification, American Society of Mechanical Engineers, 2^nd ed., 2001.


18. A. A. Omar, “Effects of Welding Parameters on Hard Zone Formation at Dissimilar Metal Welds”, Weld J, Vol. 77, 1998, pp. 86-93.