Failure Mode and Effect Analysis Power Plant Boiler

Subject Areas : Economics

Guntur Pratama Putra ¹ , Humiras Hardi Purba ²

1 - Master of Industrial Engineering, MercuBuana University,Jakarta, Indonesia
2 - Master of Industrial Engineering, MercuBuana University,Jakarta, Indonesia

Received: 2017-12-02 Accepted : 2018-05-24 Published : 2018-07-01

Keywords:

References:

Afefy, I. H. (2010). Reliability-Centered Maintenance Methodology and Application: A Case Study. Engineering, 2(11), 863–873. https://doi.org/10.4236/engineering.2010.211109

Afefy, I. H. (2015). Hazard Analysis and Risk Assessments for Industrial Processes Using FMEA and Bow-Tie Methodologies, 14(4), 379–391.

Al-khafaji, S. K. H. (2005). Design of a Programmable System for Failure Modes and Effect Analysis of Steam-Power Plant Based on the Fault Tree Analysis, 1(2), 64–85.

Ambekar, S., Edlabadkar, A., & Shrouty, V. (2013). A Review: Implementation of Failure Mode and Effect Analysis. Ijeit.Com, 2(8), 37–41. Retrieved from http://ijeit.com/vol 2/Issue 8/IJEIT1412201302_07.pdf

Carazas, F. J. G., Salazar, C. H., & Souza, G. F. M. (2011). Availability analysis of heat recovery steam generators used in thermal power plants. Energy, 36(6), 3855–3870. https://doi.org/10.1016/j.energy.2010.10.003

Chikhale, S. S., & Barik, M. K. (2015). Failure Mode and Effect Analysis on Base Frame – Case Study. Journal of Emerging Technologies and Innovative Research, 2(4), 1283–1288.

Dobrivoje, Ć. (2011). Fmea in product development phase. Fmea in Product Development Phase, 679–686.

Lipol, L. S., & Haq, J. (2011). Risk analysis method : FMEA / FMECA in the organizations . International Journal of Basic & Applied Sciences, 11(5).

Management, N. (2013). Simple approach to failure modes using a maintenance organisation and management software (1) Marcelo Batista , José Fernandes (1) and Alexandre Veríssimo (1), (1).

Mutlu, N. G., Altuntas, S., & Türkdoğan, İ. (2016). Failure modes and effects analysis for cogeneration unit in a wastewater treatment plant Failure modes and effects analysis for cogeneration unit in a wastewater treatment plant, (September), 0–7.

Nagar, V. (2013). Boiler Efficiency Improvement through Analysis of Losses. International Journal for Scientific Research & Development, 1(3), 1–5.

Othman, H., Purbolaksono, J., & Ahmad, B. (2009). Failure investigation on deformed superheater tubes. Engineering Failure Analysis, 16(1), 329–339. https://doi.org/10.1016/j.engfailanal.2008.05.023

Popović, V., Vasić, B., & Petrović, M. (2010). The possibility for FMEA method improvement and its implementation into bus life cycle. Strojniski Vestnik/Journal of Mechanical Engineering, 56(3), 1–7.

Purbolaksono, J., Ahmad, J., Beng, L. C., Rashid, A. Z., Khinani, A., & Ali, A. A. (2010). Failure analysis on a primary superheater tube of a power plant. Engineering Failure Analysis, 17(1), 158–167. https://doi.org/10.1016/j.engfailanal.2009.04.017

Puspitasari, N. B., & Martanto, A. (2014). Penggunaan FMEA dalam Mengidentifikasi Resiko Kegagalan Proses Produksi Sarung ATM (Alat Tenun Mesin) (Studi Kasus PT ASAPUTEX Jaya Tegal). J@TI Undip, IX(2), 93–98.

Rakesh, R., Jos, B. C., & Mathew, G. (2013). FMEA Analysis for Reducing Breakdowns of a Sub System in the Life Care Product Manufacturing Industry. International Journal of Engineering Science and Innovative Technology, 2(2), 218–225.

S. Parsana, T., & T. Patel, M. (2014). A Case Study: A Process FMEA Tool to Enhance Quality and Efficiency of Manufacturing Industry. Bonfring International Journal of Industrial Engineering and Management Science, 4(3), 145–152. https://doi.org/10.9756/BIJIEMS.10350

Sellappan, N., & Palanikumar, K. (2013). Modified Prioritization Methodology for Risk Priority Number in Failure Mode and Effects Analysis. International Journal of Applied Science and Technology, 3(4), 27–36.

Sharma, K. D., & Srivastava, S. (2016). Failure Mode and Effect Analysis ( FMEA ) for Enhancing Reliability of Water Tube Boiler in Thermal Power Plant, 8(2).

Shivakumar, K. M., Hanumantharaya, R., & A, M. U. M. K. (2015). Implementation of FMEA in Injection Moulding Process, 22(5), 230–235.

Tomašková, M. (1929). Fmea-Analysis of Restricted Pressure Device for, (508), 46–54.