Investigation of increasing surface hardness of 316L stainless steel using amorphous aluminum phosphate coating

Subject Areas : Journal of New Applied and Computational Findings in Mechanical Systems

tara bazdar ¹ , Abdolmajid Eslami ² , ahmad monshi ³ , Fatemehsadat Sayyedan ⁴ , Alireza Abbasloo ⁵

1 - Department of Corrosion and Materials Protection, Faculty of Materials engineering, Isfahan University of Technology, Isfahan, Iran
2 - Head of corrosion and materials protection department, faculty of materials engineering, isfahan university of technology, Isfahan, Iran
3 - materials department, engineering faculty, islamic azad university-ahvaz branch, ahvaz,, iran department of materials engineering, isfahan university of technology, isfahan, iran.
4 - Faculty of materials engineering, isfahan university of technology, isfahan, iran
5 - Head of research and development of shahre babak copper complex, Shahre babak, Iran

Received: 2021-08-28 Accepted : 2021-09-19 Published : 2021-08-23

Keywords: Hardness, stainless steel, Coating, Amorphous aluminum phosphate,

Abstract :

In this study, amorphous aluminum phosphate coating was applied on 316L stainless steel surface to increase hardness and chemical resistance. Amorphous means no crystal structure and grain boundaries due to the lack of weaknesses related to these two parameters. In this synthesis, ethanol-based aluminum nitrate nonahydrate and phosphorus oxide precursor solutions were used. It was heated to 70 ° C for 15 minutes to obtain a clear sol with 75% by weight of aluminum phosphate and a molar ratio of aluminum to phosphorus of 1.75. After activating the surface of steel plates and immersion in aluminum phosphate sol, it was heated in three stages of one minute for 24 hours at 65 ° C and 30 minutes at 500 ° C. Continuous X-RAY diffraction pattern proved the existence of an amorphous structure and showed that it is controlled with some extra aluminum. Scanning electron microscopy images and spectroscopic analysis showed that the peeling of the coating in marble-activated samples was better than that of Aqua-Regia and Loria. The microhardness test on the heat-treated sample at 500 ° C showed a threefold increase in hardness compared to the substrate metal.

References:

[1] Meetham G. (1986). Use of protective coatings in aero gas turbine engines. Materials science and technology 2(3). pp 290-294.

[2] Pomeroy M. (2005). Coatings for gas turbine materials and long term stability issues. Materials & design 26(3). pp 223-231.

[3] Shi F. (2012). Ceramic Coatings: Applications in Engineering. Intech Open, 249.

[4] Song R. (2003). Hydrogen permeation resistance of plasma-sprayed Al2O3 and Al2O3–13wt.% TiO2 ceramic coatings on austenitic stainless steel. Surface and Coatings Technology 168(2-3). pp 191-194.

[5] Salman S, Köse R, Urtekin L, Findik F. (2006). An investigation of different ceramic coating thermal properties. Materials & design 27(7). pp 585-590.

[6] Xu R, Pang W, Yu J, Huo Q, Chen J. (2008). Chemistry of zeolites and related porous materials: synthesis and structure, pp 253-255.

[7] sambasivan S, Steiner, KA. High Temperature Amorphous Composition Based on Aluminium Phosphate, 2004. US Patent No. 0011245

[8] Sambasivan S, Steiner, KA, Rangan, KK. Aluminum Phosphate Coatings, 2007. US Patent No. 7,311,944 B2

[9] sambasivan S , Steiner, KA, Rangan, KK. (2010). Aluminum Phosphate Coatings, Patent No. 0297000 A1

[10] Li N, Zhong M, Xu Z, Zhang Z. (2018). Polyesterification synthesis of amorphous aluminum phosphate thermal radiation material with high infrared emissivity. Materials Letters 213(pp 335-337.

[11] Liu M, Hu H, Zheng Y. (2017). Effects of three sealing methods of aluminum phosphate sealant on corrosion resistance of the Fe-based amorphous coating. Surface and Coatings Technology 309. pp 579-589.

[12] Wu F, Zhang X, Zhao, Taolin L, Li X, Man C. Renjie. (2015). Multifunctional AlPO4 coating for improving electrochemical properties of low-cost Li [Li0. 2Fe0. 1Ni0. 15Mn0. 55] O2 cathode materials for lithium-ion batteries. ACS applied materials & interfaces 7(6). pp 3773-3781.

[13] Walker L, Marotto V, Rafiee M, Koratkar N, Corral E. (2011). Toughening in graphene ceramic composites. ACS nano 5(4). pp 3182-3190.

[14] Sayyedan F, Enayati, M. (2019). On structure and oxidation behaviour of non-stoichiometric amorphous aluminium phosphate coating. Surface Engineering 35(8). pp 670-676.

[15] Bramfitt B, Benscoter A. (2001). Metallographer's guide: practice and procedures for irons and steels. Asm International. pp 360-367.

[16] Sayyedan FS, Enayati, MH. (2018). Evaluating oxidation behavior of amorphous aluminum phosphate coating. Applied Surface Science 455 .pp 821-830.