Crack Tip Constraint for Anisotropic Sheet Metal Plate Subjected to Mode-I Fracture

Subject Areas : Engineering

R  Kacker ¹ (Department of Industrial and Production Engineering, National Institute of Technology, Jalandhar, India)
S.S  Bhadauria ² (Department of Industrial and Production Engineering, National Institute of Technology, Jalandhar, India)

Received: 2016-03-14 Accepted : 2016-05-12 Published : 2016-06-30

Keywords:

References:

Lou Y., Yoon J. W., Huh H., 2014, Modeling of shear ductile fracture considering a changeable cut-off value for stress triaxiality, International Journal of Plasticity 54: 56-80.
[2] Ognedal A.S., Clausen A. H., Dahlen A., Hopperstad O. S., 2014, Behavior of PVC and HDPE under highly triaxial stress states: An experimental and numerical study, Mechanics of Materials 72: 94-108.
[3] Lou Y., 2013, Evaluation of ductile fracture criteria in a general three-dimensional stress state considering the stress triaxiality and the, Acta Mechanica Solida Sinica 26(6): 642-658.
[4] Paul S. K., 2013, Effect of martensite volume fraction on stress triaxiality and deformation behavior of dual phase steel, Materials & Design 50: 782-789.
[5] Jackiewicz J., 2011, Use of a modified Gurson model approach for the simulation of ductile fracture by growth and coalescence of microvoids under low, medium and high stress triaxiality loadings, Engineering Fracture Mechanics 78(3): 487-502.
[6] Peirs J., Verleysen P., Degrieck J., 2011, Experimental study of the influence of strain rate on fracture of Ti6Al4V, Procedia Engineering 10: 2336-2341.
[7] Ha S., Ã K. K., 2010, Void growth and coalescence in f . c . c . single crystals, International Journal of Mechanical Sciences 52(7):863-873.
[8] Trattnig G., Antretter T., Pippan R., 2008, Fracture of austenitic steel subject to a wide range of stress triaxiality ratios and crack deformation modes, Engineering Fracture Mechanics 75: 223-235.
[9] Bru M., Chyra O., Albrecht D., 2008, A ductile damage criterion at various stress triaxialities, International Journal of Plasticity 24:1731-1755.
[10] Zhang W., Deng X., 2007, Mixed-mode I/II fields around a crack with a cohesive zone ahead of the crack tip, Mechanics Research Communications 34: 172-180.
[11] Zhu H., Zhu L., Lv X., 2007, Investigation of fracture mechanism of 6063 aluminum alloy under different stress states , International Journal of Fracture 146:159-172.
[12] Bao Y., 2005, Dependence of ductile crack formation in tensile tests on stress triaxiality, stress and strain ratios, Engineering Fracture Mechanics 72(4):505-522.
[13] Bao Y., Wierzbicki T., 2005, On the cut-off value of negative triaxiality for fracture, Engineering Fracture Mechanics 72 :1049-1069.
[14] Bao Y., Wierzbicki T., 2004, On fracture locus in the equivalent strain and stress triaxiality space, International Journal of Mechanical Sciences 46: 81-98.
[15] Kim Y., Schwalbe K., 2004, Numerical analyses of strength mis-match effect on local stresses for ideally plastic materials, Engineering Fracture Mechanics 71:1177-1199.
[16] Hopperstad O. S., Børvik T., Langseth M., Labibes K., Albertini C., 2003, On the influence of stress triaxiality and strain rate on the behaviour of a structural steel, European Journal of Mechanics- A/Solids 22: 1-13.
[17] Shama A., Zarghamee M., Ojdrovic R., Schafer B., 2003, Seismic damage evaluation of a steel building using stress triaxiality, Engineering Structures 25: 271-279.
[18] Ores B., Co M., Str A., 2001, The effect of stress triaxiality on tensile behavior of cavitating specimens, Journal of Materials Science 6: 5155-5159.
[19] City K., 2000, Fracture and yield behavior of adhesively bonded joints under triaxial stress conditions, Journal of Materials Science 5: 2481-2491.
[20] Zhu Y., Dodd B., Caddell R. M., Hosford W. F., 1987, Convexity restrictions on non-quadratic anisotropic yield criteria, International Journal of Mechanical Sciences 29(10): 733-741.
[21] Hance B.M., 2005, Influence of Discontinuous Yielding on Normal Anisotropy (<I>R</I>-Value) Measurements, Journal of Materials Engineering and Performance 14: 616-622.
[22] Bhadauria S. S., Hora M. S., Pathak K. K., 2009, Effect of stress triaxiality on yielding of anisotropic, Journal of Solid Mechanics 1(3): 226-232.