Effects of HFRW Variables on Weldded Joint Quality of the Ferritic Stainless Steel to Cr-Mo Low Alloy Steel in Heat Recovery Steam Generator

Subject Areas : Journal of Environmental Friendly Materials

M Sadeghi ¹ , H Sabet ² , H Razavi ³

1 - Department of Materials Engineering, Karaj Branch, Islamic Azad University, Karaj, Iran
2 - Department of Materials Engineering, Karaj Branch, Islamic Azad University, Karaj, Iran
3 - School of Metallurgy and Materials Engineering, Iran University of Science and Technology, Tehran, Iran

Received: 2020-02-12 Accepted : 2020-03-07 Published : 2020-06-01

Keywords: Finned tube, Heat recovery steam generator, Resistance Welding, AISI 409, 2 ¼ Cr-1Mo,

References:

[1]  Z. Dziemidowicz, P. Szyszka and I. Krupa : Power units on the horizon. The technical requirements of new generation units at PGE Power Plant Opole S.A. Electric Heat and Vocational Education, 11, (2011).

[2] V. Eriksen, Heat Recovery Steam Generator Technolo. , Woodhead Publishing, (2017).

[3] J. Mitrovic, Heat Exchanger and Condenser Tubes, Tube Types Materials Attributes Machining. Publico Publications, (2004).

[4] P. Breeze, Raising steam plant efficiency – Pushing the steam cycle boundaries. PEI Magazine 20, (2012).     

[5] E. Pis’mennyi, P. Georgiy, C. Ignacio, S. Florencio and I. Pioro, Handbook for Transversely Finned  Tube  Heat Exchanger Design Academic Press ,(2016).

[6] R. Kocurek and J. Adamiec, Adv. Mater. Sci., 13, 3 (37), (2013), 26.

[7] J. Adamiec and M. Więcek,Biuletyn Institute Spawalnictwa ,5, (2014), 41.

[8] N. Erling, Appl. Therm. Eng. 30, 1531e1537, (2010).

[9] S. R. Mcilwain, A Comparison of Heat Transfer around a Single Serrated, IJRRAS 2 (2), (2010), 88.

[10] J. Noordermeer, P. Eng, IAGT Symposium, Training Sessions, Banff Alberta, (2013).

[11] R. Huseman : Advanced (700°C) PF Power Plant. A Clean Coal European Technology. Advanced Material for AD700 Boilers, Cesi Auditorium, Milano, (2010).  

[12] H. Kushima, T. Watanabe, M. Murata, K. Kamihira, H. Tanaka and K. Kimura, Metallographic Atlas for 2.25Cr-1Mo Steels and Degradation due to Long-term Service at the Elevated Temperatures , ECCC Creep Conference, )2005(, 223.

[13] B. King, Welding and Post Weld Heat Treatment of 2.25%Cr-1%Mo Steel, M.Eng thesis, Faculty of Engineering, University of Wollongong Australia, (2005), 13.

[14] L. Wagner Ferreira, R. Glaucio, C. Heloisa,  M. Furtadoa, L. Barreto and A. Luiz Henrique de, , Mater. Res., 10, 1590, (2017), 0596.

[15] S. Zuback, T. Mukherjee, T. A. Palmer and T. DebRoy, Novel Dissimilar Joints between 2.25Cr-1Mo Steel and Alloy 800H through Additive Manufacturing, Pennsylvania State University, AWS FABTECH Conference, Las Vegas, NV (2016).

[16] C. Ornek, Performance Characterisation of  Duplex Stainless Steel in Nuclear Waste Storage Environment, PhD thesis, University of Manchester, (2015), 25.

[17] ASTM A 240 Standard Specification for heat resisting chromium and chromium-nickel stainless steel strip for pressure vessels, (2020).

[18] ASTM A213 Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes, (2020).