The Effect of Cooling Rate on the Microstructure and Mechanical Properties of the Plastic Injection Molds

Subject Areas : Journal of Environmental Friendly Materials

Z. S  Seyedraoufi ¹ (Advanced Materials Engineering Research Center, Karaj Branch, Islamic Azad University, Karaj, Iran)
M  Samiee ² (Advanced Materials Engineering Research Center, Karaj Branch, Islamic Azad University, Karaj, Iran)
F  Abdi ³ (Institute of Materials and Energy, Karaj, Iran)

Received: 2021-01-30 Accepted : 2021-04-15 Published : 2021-06-01

Keywords: Hardness, Microstructure, Toughness, X210Cr12 Steel, Cryogenic,

References:

[1] S. G. Sapate, A. D.  Chopde, P. M. Nimbalkar and D. M. Chandarkar, Mater. Des., 28(2007), 1923.

[2] I. Sevim and I. B.  Eryurek, Kov. Mater., 43(2005), 158.

[3]H. Jirková, K. Rubešová, P. Konopík and K. Opatová, Metals., 8(2018), 713.

[4]D. Tobola, W. Brostow, K. Czechowski and P. Rusek, Wear., 382(2017) 29.

[5]R. Karimdadashi and M. A. Mohtadi-bonab, Int. j. Res. Appl. Sci. Eng. Technol., 4)2016(, 2321.

[6]A. Bensely, A. Prabhakaran, D. Mohan Lal and G. Nagarajan, Cryogenics., 45(2005), 747.

[7] Y. Dong, X. Lin and H.S. Xiao, Heat Treat. Met., 25(1998), 55.

[8] J.D. Darwin, D. Mohan Lal and G. Nagarajan, J. Mater. Process. Technol., 195(2008), 241.[9] M. Sitko and B. Skoczeń, Int. J. Solids. Struct., 49 (2012), 613.

[10]W. Han, Y. Liu, F. Wan, P. Liu, X. Yi, Q. Zhan, D. Morrall and S. Ohnuki, J. Nucl. Mater., 504(2018), 29.

[11]V. G. Gavriljuk, W. Theisen, V. V. Sirosha, E. V. Polshin, A. Kortmann, G. S. Mogilny, Y. N.Petrov and Y. V. Tarusin, Acta Mater., 61 (2013) 1705.

[12]A. Gural, Kov. Mater., 48(2010), 25.

[13]R. Ebner, H. Leitner, F. Jeglitch and D. Caliskanoglu, Proc. of the 5th Int. Conference on Tooling, Leoben, (1999), 3.

[14]D. Tobola, W. Brostow, K. Czechowski and P. Rusek, Wear., 382(2017) 29.

[15] R. Hood, F. M. Aguirre, L. S. Gonzalez, D. Novovic and S. L. Soo, Manuf. Technol., 68(2019) 329.

[16] M. Novelli, P. Bocher and T. Grosdidier, Mater. Charact., 139(2018),197.

[17] V. Vinay, M. R. Ramesh and D. Chakradhar, J. Manuf. Proc., 37(2019), 242.

[18] W. Kaikai, K. Gu, J. Miao, Z. Weng, J. Wang, Z. Tan and B. Bai, Mater. Sci. Eng. A., 743(2019), 259.

[19] P.Germán, J. E. P. Ipiña and W. R. Tuckart, Mater. Sci. Eng. A., 605(2014), 236.