Subject Areas : journal of New Materials

سعید کریمی ¹ (دانشجوی دکترای مهندسی مواد، دانشگاه شیراز.)
سیروس جوادپور ² (دانشیار و عضو هیئت علمی بخش مهندسی مواد، دانشگاه شیراز)

Received: 2015-12-29 Accepted : 2015-12-29 Published : 2012-06-21

Keywords:

References:

1- F. Ryan, B. Caulfield, "Examining TheBenefits of Using Bio-CNG in Urban Bus

Operations", Transportation Research Part D:Transport and Environment, Vol. 15 (6), 362-

365, 2010.

2- M. U. Aslam, H. H. Masjuki, M. A. Kalam,H. Abdesselam, T. M. I. Mahlia, M. A.

Amalina, "An Experimental Envestigation ofCNG as an Alternative Fuel for a Retrofitted

Gasoline Vehicle", Fuel, Vol. 85 (5-6), 717-724, 2006.

3- S. Yeh, "An Empirical Analysis on theAdoption of Alternative Fuel Vehicles: The

Case of Natural Gas Vehicles", Energy Policy,Vol. 35 (11), 5865-5875, 2007.

4- ISO standard: 11439 (2000), "Gas Cylinders- High Pressure Cylinders for the On-Board

Storage of Natural Gas as a Fuel forAutomotive Vehicles".

5- ANSI/CSA standard: NGV2 (2000), "BasicRequirements for Compressed Natural Gas

Vehicle (NGV) Fuel Containers".6- A. Önder, O. Sayman, T. Dogan, N.Tarakcioglu, "Burst Failure Load of Composite

Pressure Vessels", Composite Structures, Vol.89 (1), 159-166, 2009.

7- L. Zu, S. Koussios, A. Beukers, "OptimalCross Sections of Filament-Wound Toroidal

Hydrogen Storage Vessels Based onContinuum Lamination Theory", International

Journal of Hydrogen Energy, Vol. 35 (19),10419-10429, 2010.

8- L. Zu, S. Koussios, A. Beukers, "ShapeOptimization of Filament Wound Articulated

Pressure Vessels Based on Non-GeodesicTrajectories", Composite Structures, Vol. 92(2), 339-346, 2010.

9- L. Zu, S. Koussios, A. Beukers, "Design ofFilament-Wound Isotensoid Pressure Vessels

With Unequal Polar Openings",Composite Structures, Vol. 92 (9), 2307-2313,2010.

10- A. Vafaeesefat, "Dome ShapeOptimization of Composite Pressure vessels

Based on Rational B-Spline Curve and GeneticAlgorithm", Applied Composite Materials,

Vol. 16 (5), 321-330, 2009.

11- T. L. Teng, C. M. Yu, Y. Y. Wu, "OptimalDesign of Filament-Wound Composite

Pressure Vessels", Mechanics of CompositeMaterials, Vol. 41 (4), 333-340, 2005.

12- Z. Changliang, R. Mingfa, Z. Wei, C.Haoran, "Delamination Prediction of

Composite Filament Wound Vessel with MetalLiner Under Low Velocity Impact", CompositeStructures, Vol. 75 (1-4), 387-392, 2006.

13- P. Xu, J. Y. Zheng, P. F. Liu, "FiniteElement Analysis of Burst Pressure of

Composite Hydrogen Storage Vessels",Materials and Design, Vol. 30 (7), 2295-2301,2009.

14- C. S. Mao, M. F. Yang, D. G. Hwang, H.C. Wang, "An Estimation of Strength for

Composite Pressure Vessels", CompositeStructures, Vol. 22 (3), 179-186, 1992.

15- C. Frias, H. Faria, O. Frazo, P. Vieira, A.T. Marques, "Manufacturing and Testing

Composite Overwrapped Pressure Vesselswith Embedded Sensors", Materials and

Design, Vol. 31 (8), 4016-4022, 2010.

16- D. Cohen, S. C. Mantell, L. Zhao, "TheEffect of Fiber Volume Fraction on Filament

Wound Composite Pressure Vessel Strength",Composites, Vol. 32 (5), 413-429, 2001.

17- ASTM standard:B 308/B 308M (2002),“Standard Specification for Aluminum – alloy6061- T6 Standard Structural Profiles”

18- A. K. Kaw, Mechanics of CompositeMaterials, 2ed., p. 203-301, CRC Press,London, 2005.

19- S. Karimi, "Materials Selection and Designfor Manufacturing a Suitable Composite CNGTank", M.S. Thesis Shiraz University, 2011.