References:
1- F. Ryan, B. Caulfield, "Examining TheBenefits of Using Bio-CNG in Urban Bus
Operations", Transportation Research Part D:Transport and Environment, Vol. 15 (6), 362-
365, 2010.
2- M. U. Aslam, H. H. Masjuki, M. A. Kalam,H. Abdesselam, T. M. I. Mahlia, M. A.
Amalina, "An Experimental Envestigation ofCNG as an Alternative Fuel for a Retrofitted
Gasoline Vehicle", Fuel, Vol. 85 (5-6), 717-724, 2006.
3- S. Yeh, "An Empirical Analysis on theAdoption of Alternative Fuel Vehicles: The
Case of Natural Gas Vehicles", Energy Policy,Vol. 35 (11), 5865-5875, 2007.
4- ISO standard: 11439 (2000), "Gas Cylinders- High Pressure Cylinders for the On-Board
Storage of Natural Gas as a Fuel forAutomotive Vehicles".
5- ANSI/CSA standard: NGV2 (2000), "BasicRequirements for Compressed Natural Gas
Vehicle (NGV) Fuel Containers".6- A. Önder, O. Sayman, T. Dogan, N.Tarakcioglu, "Burst Failure Load of Composite
Pressure Vessels", Composite Structures, Vol.89 (1), 159-166, 2009.
7- L. Zu, S. Koussios, A. Beukers, "OptimalCross Sections of Filament-Wound Toroidal
Hydrogen Storage Vessels Based onContinuum Lamination Theory", International
Journal of Hydrogen Energy, Vol. 35 (19),10419-10429, 2010.
8- L. Zu, S. Koussios, A. Beukers, "ShapeOptimization of Filament Wound Articulated
Pressure Vessels Based on Non-GeodesicTrajectories", Composite Structures, Vol. 92(2), 339-346, 2010.
9- L. Zu, S. Koussios, A. Beukers, "Design ofFilament-Wound Isotensoid Pressure Vessels
With Unequal Polar Openings",Composite Structures, Vol. 92 (9), 2307-2313,2010.
10- A. Vafaeesefat, "Dome ShapeOptimization of Composite Pressure vessels
Based on Rational B-Spline Curve and GeneticAlgorithm", Applied Composite Materials,
Vol. 16 (5), 321-330, 2009.
11- T. L. Teng, C. M. Yu, Y. Y. Wu, "OptimalDesign of Filament-Wound Composite
Pressure Vessels", Mechanics of CompositeMaterials, Vol. 41 (4), 333-340, 2005.
12- Z. Changliang, R. Mingfa, Z. Wei, C.Haoran, "Delamination Prediction of
Composite Filament Wound Vessel with MetalLiner Under Low Velocity Impact", CompositeStructures, Vol. 75 (1-4), 387-392, 2006.
13- P. Xu, J. Y. Zheng, P. F. Liu, "FiniteElement Analysis of Burst Pressure of
Composite Hydrogen Storage Vessels",Materials and Design, Vol. 30 (7), 2295-2301,2009.
14- C. S. Mao, M. F. Yang, D. G. Hwang, H.C. Wang, "An Estimation of Strength for
Composite Pressure Vessels", CompositeStructures, Vol. 22 (3), 179-186, 1992.
15- C. Frias, H. Faria, O. Frazo, P. Vieira, A.T. Marques, "Manufacturing and Testing
Composite Overwrapped Pressure Vesselswith Embedded Sensors", Materials and
Design, Vol. 31 (8), 4016-4022, 2010.
16- D. Cohen, S. C. Mantell, L. Zhao, "TheEffect of Fiber Volume Fraction on Filament
Wound Composite Pressure Vessel Strength",Composites, Vol. 32 (5), 413-429, 2001.
17- ASTM standard:B 308/B 308M (2002),“Standard Specification for Aluminum – alloy6061- T6 Standard Structural Profiles”
18- A. K. Kaw, Mechanics of CompositeMaterials, 2ed., p. 203-301, CRC Press,London, 2005.
19- S. Karimi, "Materials Selection and Designfor Manufacturing a Suitable Composite CNGTank", M.S. Thesis Shiraz University, 2011.
