Subject Areas : journal of New Materials
1 - عضو هیئت علمی دانشگاه آزاد اسلامی، واحد مرودشت، گروه مکانیک، مرودشت، ایران
2 - کارشناس ارشد مکانیک
Keywords:
Abstract :
References:
1- W. F. Hosford, Metal forming Mechanicsand Metallurgy, 3rd ed., p. 110, Cambridge
University Press, New York 2007.
2- K. L. Johnson and R. H. Bentall, “The onsetof yield in the cold rolling of thin strip”,
Journal of the Mechanics and Physics ofSolids, Vol. 17, pp. 253-264 , 1969.
3- N. A. Fleck and K.L Johnson, “Cold rollingof foil”, Proceedings of the Institution of
Mechanical Engineers, Vol. 206, pp. 119-131,1992.
4- H. R. Le and M. P. F. Sutcliffe, “A robustmodel for rolling of thin strip and foil”,
International Journal of Mechanical SciencesVol. 43, pp. 1405-1419, 2001.
5- W. Y. D. Yuen, A. Dixon and D. N.Nguyen, “The modeling of the mechanics of
deformation in flat rolling”, Journal ofMaterials Processing Technology, Vol. 60, pp.
87-94, 1996.
6- M. Abo-Elkhier, “Elasto-plastic finiteelement modeling of strip cold rolling using
Eulerian fixed mesh technique”, FiniteElements in Analysis and Design, Vol. 27, pp.
323-334, 1997.
7- P. R. Dawson and E. G. Tompson, “Finiteelement analysis of steady state elasto-viscoplastic
flow by the initial stress rate method”,International Journal for Numerical Methods in
Engineering, Vol. 12, pp. 47-57, 1978.
8- G. J. Li and S. Kobayashi, “Rigid-Plasticelement analysis of plane strain rolling”,
J. Eng. Ind., Vol. 104, p. 55, 1982.
9- Y. J. Hwu and J.G. Lenard, “A finitestudy of flat rolling”, Journal of
Engineering Materials and Technology, Vol.110, pp. 22-27, 1988.
10- R. S. Prakash, P.M. Dixit and G. K. Lal,“Steady state plane strain cold rolling of a
strain hardening material”, Journal ofMaterials Processing Technology, Vol. 52, pp.
338-358, 1995.
11- U.S Dixit and P.M Dixit, “Finite elementanalysis of flat rolling with inclusion of
anisotropy”, International Journal ofMechanical Sciences, Vol. 39, pp. 1237-1255,
1997.
12- K. Komori, “Rigid-Plastic finite elementmethod for analysis of three dimensional
rolling”, International Journal of MechanicalSciences, Vol. 40, pp. 479-491, 1998.
13- Z. Y. Jiang and A. K. Tieu, “A simulationof three-dimensional metal rolling processes
by rigid-plastic finite element”, Journal ofMaterials Processing Technology, Vol. 112,
pp. 144-151, 2001.
14- S. Sezek, B. Aksakal, and Y.Can,“Analysis of cold and hot plate rolling using
dual stream functions”, Materials & Design,Vol. 29, pp. 584-596, 2008.
15- Z. Y. Jiang, S.W. Xiong and Q.J. Wang,“Modeling of the effect of friction on cold strip
rolling”, Journal of Materials ProcessingTechnology, Vol. 201, pp. 85-90, 2008.
16- F. A. R. Al-Salehi, T. C. Firbank and P. R.Lancaster, “An Experimental determination for
the roll pressure distributions in cold rolling”,International Journal of Mechanical Sciences,
Vol. 15, pp. 693-700, 1973.
