protrusion friction stir spot welding: the microstructure and mechanical properties of Al 6061 alloy

Subject Areas : journal of New Materials

omid zarei ¹ , mostafa mosavizade ² , fateme zarghani ³ , hamed zarei ⁴

1 - Department of Materials and Polymer Engineering, Hakim Sabzevari University, Sabzevar, Iran
2 - Department of Materials Science and Engineering, University of Gonabad,
3 - Department of Materials and Polymer Engineering, Hakim Sabzevari University, Sabzevar, Iran
4 - Department of Materials and Polymer Engineering, Hakim Sabzevari University, Sabzevar, Iran

Received: 2019-02-20 Accepted : 2019-06-23 Published : 2019-06-22

Keywords: mechanical properties, Friction stir spot welding.Microstructure, 6061 AL alloy,

Abstract :

With the successful application of the protrusion spot friction stir welding technology to 2024 aluminum alloy and low carbon steel plate with a thickness of 1 mm , this technique was expanded to the spot welding of 1 mm thick 6061 aluminum alloy in this study. The effects of the tool dwell time (6, 12, 18 s) and plunging depth (0.1, 0.14 and 0.18 mm) were investigated on the microstructure and mechanical properties of samples. Surface appearance of the welding zone showed that the keyhole was not formed and the appearance of weld was relatively smooth. Microstructure and mechanical results indicated that the welding zone with uniform and refine structure due to dynamic recrystallization presents higher hardness and strength than base metal while can be affected by dwell time. Increasing the plunging depth increases the tensile strength and also decreases the thickness of the upper sheet.Fracture surfaces of the failed specimens present the shear fracture and the interfacial fracture.

References:

1- Joaquín M. Piccinia, Hernán G. Svobodab." Effect of the tool penetration depth in Friction  Stir Spot Welding  (FSSW) of dissimilar aluminum alloys" .Procedia Materials Science 8 ( 0).p: 868 – 877. (2015).

 

2-H. Aghajani Derazkola, H. Rahmani, M. Habibnia, M. B. Limoie, The feasibility study on  AA7075 T-joint  via friction stir welding process, Iranian Journal of Manufacturing Engineering, Vol. 3, No. 1, pp. 21-32, (2016).

 

3-N Pathak,K. Bandyopadhyay,M.Sarangi, and Sushanta Kumar Panda Microstructure  and Mechanical Performance of  Friction Stir Spot-Welded Aluminum-5754 Sheets, (2013).

 

4-PhilipB Prangnell ,and Dimitrios Bakavos "Novel Approaches to Friction Spot Welding Thin Aluminium Automotive Sheet" -Materials   Science Forum Vols, (2010).

 

5-Y. Bozkurt and S. Salman, “Effect of welding parameters on lap shear tensile properties   of dissimila         friction stir spot welded AA 5754-H22 / 2024-T3 joints,” vol. 18, no. 4,  (2013).

6-M. Yamamoto, a. Gerlich, T. H. North, and K. Shinozaki,  “Cracking and Local  Melting   in Mg-Alloy and Al-Alloy During Friction Stir Spot Welding,  ” Weld. World, vol. 52, no. 9–10, pp. 38–46, (2008).

 

7- Y. Uematsu a,*, K. Tokaji a, Y. Tozaki b, T. Kurita c, S. Murata. Effect of re-filling probe hole on tensile failure and fatigue behaviour

of friction stir spot welded joints in Al–Mg–Si alloy. International Journal of Fatigue 30 (2008) 1956–1966

 

 

8- S.Venukumar, B. Baby, S. Muthukumaran, and S. V. Kailas, “Microstructural andMechanical Properties of Walking Friction Stir Spot Welded AA 6061-T6 Sheets,” Procedia Mater. Sci., vol.6, no.Icmpc, pp.656–665, 2014.

 

 

 

9-Y. Tozaki, Y. Uematsu, K. Tokaji , A newly developed tool without probe for friction stir  spot welding and

 its performance , Journal of Materials Processing Technology 210, (2010).

 

10- Y. F. Sun, H. Fujii, N. Takaki, and Y. Okitsu, “Novel spot friction stir welding of 6061 and12-  5052 Al  alloys,” vol. 16, no. 7, pp. 605– 612, (2011).

 

11. Adrian Gerlich Æ Peter Su Æ Motomichi Yamamoto Æ. Tom H. North. Effect of welding parameters on the strain rate and microstructure of friction stir spot welded 2024 aluminum alloy. J Mater Sci (2007) 42:5589–5601

 

12. 10- M. Paidar, A. Khodabandeh, H. Najafi, and A. S. Rouh-aghdam, “An investigation on mechanical and metallurgical properties of 2024-T3 aluminum alloy spot friction welds,” Int. J. Adv. Manuf. Technol., vol. 80, no. 1–4, pp. 183–197, 2015.

 

13. S. Venukumar, S. G. Yalagi, S. Muthukumaran and S. V. KailasStatic shear strength and fatigue life of refill friction stir spot welded AA 6061-T6 sheets.

 

14- S. Dourandish, S. M. Mousavizade, H. R. Ezatpour & G. R. Ebrahimi, “Microstructure, mechanical properties and failure behaviour of protrusion friction stir spot welded 2024 aluminium alloy sheets, ( 2017).

 

15- Zarghani, F., et al., High mechanical performance of similar Al joints produced by a  novel  spot friction welding technique. Vacuum, (2018).

 

16- . زرقانی،ف. موسوی زاده،م. ابراهیمی،غ و عزت پور،ح." تاثیر زمان نگهداری و قطر شانه ابزار بر استحکام و رفتار شکست فرآیند جوشکاری اصطکاکی اغتشاشی نقطهای زائدهای آلیاژآلومینیوم2024". مجله مواد نوین/ جلد8 /شماره /4 تابستان1397

 

17- A R Shahrabadi , S M Mousavizade , H R Ezatpour and M Pouranvari Achieving high mechanical performance in protrusion friction stir spot welding (PFSSW) of DQSK steel compared to other techniques

 

18. N. Farmanbar, S.M. Mousavizade, H.R. Ezatpour, Achieving special mechanical properties with considering dwell time of AA5052 sheets welded by a simple novel friction stir spot welding. Marine Structures 65 (2019) 197–214

 

19. N Farmanbar, SM Mousavizade, M Elsa and HR Ezatpour. AA5052 sheets welded by protrusion friction stir spot welding: High mechanical performance with considering sheets thickness at low dwelling time and tool rotation speed.

 

20.Specification for Automotive Weld

Quality—Resistance Spot Welding of

Aluminum. AWS D8.2M:2017 An American National Standard

 

21- Xiao Song & Liming Ke & Li Xing & Fencheng Liu & Chunping Huang Effect of plunge speeds on hook geometries and mechanical properties in friction stir spot 1welding of  A6061-T6 sheets.

 

22- Y. Tozaki, Y. Uematsu, K. Tokaji , A newly developed tool without probe for friction stirspot welding and  its performance , Journal of Materials Processing Technology 210, (2010).

 

23- Z.  Shen, Y.  Chen, J. S. C.  Hou, X. Yang, and A. P. Gerlich, “Influence of processingparameters  on microstructure and mechanical performance of refill friction stir spot welded 7075-T6 aluminium alloy,” Sci. Technol. Weld. Join., vol. 20, no. 1, pp. 48–57, (2014).

 

24- Tran, V.-X., J. Pan, and T. Pan, Effects of processing time on strengths and failure modes  of dissimilar   spot friction welds between aluminum 5754-O and 7075-T6 sheets. Journal of materials processing technology, (2009).

 

25- Ashu Garg, Anirban Bhattacharya," On lap shear strength of friction stir spot welded   AA6061 alloy" Journal  of Manufacturing Processes, (2017).

 

26-Yutaka S. Sato, Mitsunori Urata, And Hiroyuki Kokawa Parameters Controlling  Microstructure And  

 Hardness During Friction-Stir Welding Of Precipitation-Hardenable Aluminum Alloy 6063, (2002).

 

27-R.S. Florea ,K.N. Solanki  Resistance spot welding of 6061-T6 aluminum: Failure loads and     deformation. Materials and Design, (2011).

 

28- J. L. Searles, P. I. Gouma, and R. G. Buchheit, "Stress Corrosion Cracking of Sensitized  AA5083   (Al-4.5Mg-1.0Mn)", Metallurgical and Materials Transaction A, vol. 32 (11), pp. 2859-2867, (2001).

 

29- R. G. Buchheit, "A Compilation of Corrosion Potentials Reported for Intermetallic Phases      in Aluminium Alloys", Journal of the Electrochemical Society, 142 (11), pp. 3994-3996, (1995).

 

30- J. F. Guo , H. C. Chen, C. N. Sun, G. Bi, Z. Sun, J. Wei, Friction stir welding of dissimilar2material   between AA6061 and AA7075 Al alloys effects of process parameters, Materials and Design, Vol. 56, pp. 185-192, (2014).

 

31- Olea, C., et al., A sub-structural analysis of friction stir welded joints in an AA6056  Al-alloy in T4  and T6 temper conditions. Materials Science and Engineering: A, 9, (2007).

 

32- R. S. Mishra & Z. Y. Ma, “Friction stir welding and processing”, Materials Science and  Engineering,     Vol. 50R, pp. 1-78, (2005).

 

33- D.A. Wang a,∗, S.-C. Lee b, Microstructures and failure mechanisms of friction stir 2spotwelds of aluminum 6061-T6 sheets

 

34- S. T. Amancio-Filho, S. Sheikhi, J. F. dos Santos, C.Bolfarini, Preliminary study on themicrostructure and mechanical properties of dissimilar friction stir welds in aircraft aluminum alloys 2024-T351 and 6056-T4, materials processing technology,( 2007).

 

35- Y. Tozaki, Y. Uematsu, and K. Tokaji, “Effect of tool geometry on microstructure and  static strength in friction stir spot welded aluminium alloys,” Int. J. Mach. Tools Manuf., vol. 47, no. 15, pp. 2230–2236, (2007).

 

36- H. Lee and M. Lee, Process optimisation and microstructural evolution of friction stir spot-welded   Al6061 joints, (2016).

 

37- Choi, D.-H., et al., Effect of pin shapes on joint characteristics of friction stir spot welded AA5J32 sheet. Materials transactions, (2010).

 

38- W.Yuan , R. Mishra. Effect of tool design and process parameters on properties of Al  alloy 6016 friction stir spot welds. (2011).