Producing WC-Co coating with electrolytic plasma processing on low carbon steel and investigation its wear resistance

Subject Areas : journal of New Materials

معصومه Malaei ¹ (دانشجوی کارشناسی ارشد، دانشگاه شیراز)
فاطمه Mahzon ² (عضو هیئت علمی، پژوهشکده نانو فناوری‌-دانشگاه شیراز)
کمال Janghorban ³ (عضو هیئت علمی، بخش مهندسی مواد-دانشگاه شیراز)
بابک Hashemi ⁴ (عضو هیئت علمی، بخش مهندسی مواد-دانشگاه شیراز)

Received: 2016-01-14 Accepted : 2017-11-16 Published : 2017-08-23

Keywords: abrasive wear, EDS analysis, electrolytic plasma, cermet,

Abstract :

In this study WC-Co coating was produced on low carbon steel substrate by electrolytic plasma processing (EPP). EPP is an emerging, environmentally friendly surface engineering technology. Cermet coatings can improve tribologycal properties of steel substrates. Cermet coatings which were provided by EPP not only have suitable surface features, but also have unique morphology which causes good adhesion to the substrate. The samples were coated by applying direct current and voltage of 110 volt. Morphology and cross-sectional observations and also wear path were studied by scanning electron microscope (SEM). Results of energy dispersive spectroscopy (EDS) indicate the presence of tungsten, carbon, cobalt and iron in the coating. Wear tests have been carried out with a pin on disc device and SAE52100 pin. Based on the results of this test, samples which were coated with WC-Co, show higher wear resistance and lower friction coefficient (0.7). Worn path images reveal that the dominant mechanism of wear is abrasive.

References:

1- D. M. Nuruzzaman, “Characteristics of Thermally Sprayed WC Cermet Coating Under Lubricated Rolling with Sliding Contact”,Journal of MechanicalEngineering, Vol ME37, 2007.     

2- S. Al-Mutairi, M.S.J. Hashmi, B.S. Yilbas, J. Stokes, “Microstructural Characterization of HVOF/Plasma Thermal Spray of Micro/Nano WC–12%Co Powders” Surface & Coatings Technology, Vol 264, pp 175–186, 2015.      

3- E.I. Meletis, X. Nie, F.L. Wang, J.C. Jiang, “Electrolytic Plasma Processing for Cleaning and Metal-Coating of  Steel

 Surfaces”, Surface and Coatings Technology, V 150, PP 246–256, 2002.   

4- Z.Yao, Y.Jiang, Z. Jiang, F. Wang, Z.Wu, “Preparation and Structure of Ceramic Coatings Containing Zirconium Oxide on Ti Alloy by Plasma Electrolytic Oxidation”, Journal of Materials Processing Technology, V 205, pp. 303-307, 2008.      

5-T.Paulmier, J.M.Bell, M.Fredericks, “Development of a Novel Cathodic Plasma/Electrolytic Deposition Technique

Part 1: Production of Titanium Dioxide Coatings”, Surface and Coatings Technology, Vol 201, pp.8761-8770, 2007.

6- W.C.Gu, G.H.Lv, H.Chen, G.L.Chen, W.R. Feng, G.L. Zhang, S.Z Yang, Preparation of Ceramic Coatings on Inner Surface of Steel Tubes Using a Combined Technique of Hot-Dipping and Plasma Electrolytic Oxidation, Journal of Alloys and Compounds, V 430, PP 308-312, 2007.
  7- S. Kamnis, S. Gua, T.J. Lu, C. Chen, Computational Simulation of Thermally Sprayed WC–Co Powder, Computational Materials Science, 43, 1172–1182, 2008.     

8- M. Jalali Azizpour, H. Mohammadi Majd, Residual Stress in Ground WC-Co Coatings, International Journal of Mechanical, Aerospace, Industrial, Mechatronic and Manufacturing Engineering, V 8,NO 3,2014.

9- M.W. RichertI, A. Mazurkiewicz, J.A. Smolik,the Deposition oF WC-CoCoatings by EBPVD Technique", Archives O F Metallurgy and Materials, 5, Issue 2.

10- ز. گلستان، م. جاویدی، م .ح. شریعت، ر. بازرگان لاری، پوشش دهی کامپوزیتی هیدروکسی آپاتیت - تیتانیا  همزمان با نیتروکربوره کردن با نیتروکربوره کردن الکترولیتی پلاسمایی روی سطح فولاد ضد زنگ و بررسی خواص خوردگی آن، مجله مواد نوین/ جلد 3/شماره 4/صفحات 65-74/ تابستان 1392.    

 11- ن.افسر کازرونی، م.ح. شریعت، م. بحرالعلوم، س.دهقانی، ف. محزون، ت. جوزقی، بهینه سازی حمام

به منظور کاهش ولتاژ در روش نیتروکربوره کردن الکتریکی پلاسمایی فولاد ضد زنگ آستنیتی و بررسی زیست سازگاری در بدن خرگوش، مجله مواد نوین/ جلد 1/ شماره 3/صفحات 45-54/ بهار 1390.       
           
12- D. Kekes, P. Syllabi, M. Vardavoulias, “Wear Micro-Mechanism of Composite WC-Co/Cr-NiCrFeBSiC Coatings. Part I: Dry Sliding”, Tribology in Industry, Vol 36, No 4, pp 361-374, 2014.

 13- P.Gupta, G.Tenhundfeld, E.O.Daigle, D.

Ryabkov, “Electrolytic Plasma Technology: Science and Engineering-An overview”, Surface and Coatings Technology,Vol 201, pp 8746-8760, 2007.