The effect of Al2O3 Micro Powder added in Dielectric on Electro Discharge Machining Performance of Ti6Al4V

Subject Areas : Journal of Simulation and Analysis of Novel Technologies in Mechanical Engineering

Mojtaba  Esmailian ¹ (Faculty of Mechanical, Malek Ashtar University of Technology, Iran)

Received: 2022-06-14 Accepted : 2022-08-21 Published : 2022-06-01

Keywords:

References:

 

[1] Kansal, H.K., Singh, S., Kumar, P., (2013), Technology and research developments in powder mixed electric discharge machining, Journal of Materials Processing Technology, 184, 32–41.

[2] Jeswani, M.L., (1981), Effect of the addition of graphite powder to kerosene used as the dielectric fluid in electrical discharge machining, Wear, 133–139.

[3] Furutani K., Sato H., Suzuki M., (2009), Influence of electrical conditions on performance of electrical discharge machining with powder suspended in working oil for titanium carbide deposition process, The International Journal of Advance Manufacturing Technology,  40( 11), 1093-1101.

[4]  Kumar, A., Maheshwari, S., Sharma, C., Beri, N., (2009), Performance Evaluation of Silicon Additive in Electrical Discharge Machining of EN24 Steel Based on Taguchi Method, Journal of Mechanical Engineering, 60(5–6), 298–304.

[5] Wong, Y. S., Lim, L. C., Rahuman, I., & Tee, W. M. (1998). Near-mirror-finish phenomenon in EDM using powder-mixed dielectric. Journal of Materials Processing Technology, 79(1-3), 30-40.

[6] Wu, K.L., Yan, B.H., Huang, F.Y., Chen, S.C., (2005), Improvement of surface finish on SKD steel using electro-discharge machining with aluminum and surfactant added dielectric, International Journal of Machine Tools and Manufacture, 45, 1195–1201.

[7] Lin, Y.C., Yan, B.H., Huang, F.Y., (2001), Surface modification of Al– Zn–Mg aluminum alloy using the combined process of EDM with USM, J Mater Process Technol, 115(3), 359–366.

[8] Jabbaripour, B., (2012), Investigating the effects of EDM parameters on surface integrity, MRR and TWR in machining of Ti–6Al–4V, Mach Sci Technol, 16(3), 419–444.

[9] Kolli, M., Kumar, A., (2014), Effect of boron carbide powder mixed into dielectric fluid on EDM of titanium alloy, Procedia Mater Sci, 5, 1957–1965.

[10] Ming, Q.Y., He, L.Y., (1995), Powder-suspension dielectric fluid for EDM. Journal of Materials Processing Technology, 52 (1), 44–54.

[11] Le, V.T., (2021), Influence of processing parameters on surface properties of SKD61 steel processed by powder mixed EDM, J Mater Eng Perform, 30, 3003–3023.

[12] Joshi, A. Y., & Joshi, A. Y. (2021). Multi response optimization of PMEDM of Ti6Al4V using Al2O3 and SiC powder added de-ionized water as dielectric medium using grey relational analysis. SN Applied Sciences, 3(7), 1-13.

[13] Shahbazi Dastjerdi, M., Mokhtarian, A, Saraeian, P., (2020), The effect of alumina powder in dielectric on electrical discharge machining parameters of aluminum composite A413-Al2O3 by the Taguchi method, the signal-to-noise analysis and the total normalized quality loss, International Journal of Mechanical and Materials Engineering, 15:5.

[14] HajHosseini, M.J., Mokhtarian, A.,  Rahimi, M., Masoudi, B., (2021), Investigation and optimization of the effect of input parameters on material removal rate, tool wear rate, and surface roughness in electrical discharge machining of A356 Nano-composite reinforced by alumina, Advanced Processes in Materials Engineering. 13(4), 5-18.