The effect of Al2O3 Nano-particles coated with manganese oxide on the microstructure and mechanical properties of low carbon steel using GMAW process

Subject Areas :

farzad  pahnaneh ¹ (Department of Metallurgy and Materials Engineering, Faculty of Engineering, South Tehran Branch, Islamic Azad University, Tehran, Iran)
masood  aghakhani ² (Department of Mechanical Engineering, Faculty of Engineering, Razi University, Kermanshah, Iran)
farid  naeimi ³ (Advanced Materials Research Center, Materials Engineering Department, Najafabad Branch, Islamic Azad University, Najafabad, Iran)
, Moeen  Mansoubi ⁴ (Department of Mechanical Engineering, Faculty of Engineering, Razi University, Kermanshah, Iran)

Received: 2019-04-06 Accepted : 2019-06-08 Published : 2021-04-21

Keywords: Hardness, MnO, Al2O3 Nano, particles GMAW process Microstructure Ultimate tensile strength Micro,

Abstract :

This paper reports an investigation carried out to determine the effect of aluminum oxide Nano-particles coated with manganese on the microstructure and mechanical properties of single-pass butt joint of low carbon steel plates of 6.0 mm thicknesses using gas metal arc welding process. After selecting appropriate welding parameters and adding 0.25 gr and 0.5 gr of Nano-particles into the joint line and carrying out the welding, the samples were prepared for micro hardness and tensile tests. Furthermore, the sample with optimum Nano-particles having the highest ultimate tensile strength and without having any visible and metallurgical defects in the microstructure was selected for further investigation.  Subsequently, microstructures of the weld without and with optimum Nano-particles were studied using optical microscopy and scanning electron microscopy (SEM) and the fractured surface of the weld obtained from tensile testing was investigated for the samples without Nano particles and the optimum sample with Nano materials were studied. The results show that Nano-particles added to the weld pool penetrated into the weld zone and helped in formation of acicular ferrite in the microstructure. Based on the results obtained, ultimate tensile strength and percentage of elongation of samples without Nano-particles and with optimum Nano-particles were increased from 387 MPa and 6.8% to 408 MPa and 13.6%, respectively. In addition, the average hardness of the weld metal without Nano-particles and with optimum Nano-particles were increased from 158 VHN to 172 VHN respectively

References:

[1]    AWS Handbook, "Gas Metal Arc Welding", vol. 20, 1997.

 

[2]    W. Klas, "Welding processes handbook", New York: CRC Press, 2003.

[3]    K. Shinagawa & K. Tokyo, "Essential Factors in Gas Metal Arc Welding", 141-8688, Japon. Fourth Edition, 5-912, 2011.

 

[4]    S. Kou, "Welding metallurgy", 3rd ed, New York: John Wiley & Sons Inc, pp. 19–22, 68–82, 103–114, 2003.

 

[5]    ASM. Handbook, "Welding Brazing and Soldering", Publication Information Contributors, vol. 6, 1993.

 

[6]    W. Lucas & D. Howse, "Activating flux-increasing the performance and productivity of the TIG and plasma processes", Welding & Metal Fabrication, vol. 64, no. 1, pp. 11-15, 1996.

 

[7]    M. Kuo, Z. Sun & D. Pan, "Laser welding with activating flux", Science and Technology of Welding & Joining, vol. 6, no. 1, pp. 17-22, 2001.

 

[8]    T. K. Pal & U. K. Maity, "Effect of nano size TiO₂ particles on mechanical properties of AWS E 11018M type electrode", Materials Sciences and Applications, vol. 2, no. 9, pp. 1285-1292, 2011.

 

[9]    M. Aghakhani & A. Nikzad, "Modeling of welding height in gas metal arc welding process in the presence of TiO₂ nano-particles using artificial neural network", Modares Mechanical Engineering, (in Persian), vol. 15, no. 7, pp. 149-159, 2015.

 

[10]  M. Aghakhani, M. Ghaderi, A. Karami & A. Derakhshan, "Combined effect of TiO₂ nanoparticles and input welding parameters on the weld bead penetration in submerged arc welding process using fuzzy logic", The International Journal of Advanced Manufacturing Technology, vol. 70, no. 1-4, pp. 63-72, 2014.

 

[11] C. Vimalraj, P. Kah, B. Mvola & M. Jukka, "Effect of nanomaterial addition using gmaw and GTAW processes", Rev. Adv. Mater. Sci, pp. 370-382, 2016.

 

[12] S. Mohan, S. P. Sivapirakasama, M. C. Kumarb & M. Surianarayana, "Welding fumes reduction by coating of nano-TiO2on electrodes", Journal of Materials Processing Technology, vol. 219, pp. 237–247, 2015.

 

[13]  M. Muzamila, C. Jianjun, A. Maaz, V. Patelb, A. Majeeda & J. Yanga, "Multicomponent enabled MWCNTs-TiO₂ nano-activating flux for controlling the geometrical behavior of modified TIG welding joint process" Diamond & Related Materials, vol. 97, pp. 107442, 2019.

 

[14] S. Tanvir, S. K. Tiwari & D. K. Shukla, "Friction-stir welding of AA6061-T6: The effects of Al₂O₃ nano-particles addition", Results in Materials, vol. 1, 2019.

 

[15] ASM. Handbook, "Metallography and Microstructures", The Materials Information Company, vol. 9, 1992.

 

[16] ASTM. Handbook, "Metals Mechanical Testing Elevated and Low Temperature Tests", Metallography, vol. 1, 2013.

 

[17] K. Hung Tseng, "Performance of activated TIG process in austenitic stainless steel welds", Journal of Materials Processing Technology, 2011.

 

[18] A. Kumar Singh, V. Dey & R. Naresh Rai, "Techniques to improve weld penetration in TIG welding (A review) ", Materials Today: Proceedings, vol. 4, pp. 1252–1259, 2017.

 

[19] A. Dabiri,  R. Yousefi & Fattahi, "Effect of ZrO₂ nanoparticles on the impact properties of shielded metal arc welds",  Materials Letters, vol. 158, pp. 325–328, 2015.

 

[20] T. Pan, et al, "Kinetics and mechanisms of intragranular ferrite nucleation on nano- metallic inclusions in low carbon steel", Materials Science and Engineering. A, vol. 438-440, pp. 1128-1132. 2006.

 

[21] J. H. Shim, Y. W. Cho, S. H. Chung & etc, "Nucleation of Intragranular Ferrite at Ti2o3 Particle in Low Carbon Steel", South Korea.Division of Materials Science and Engineering, Seoul National University, Seoul, pp. 151-742.1999.

 

[22] M. Aghakhani, M. R. Ghaderi, M. Mahdipour Jalilian & A. Derakhshan, "Predicting the combined effect of TiO₂ nano-particles and welding input parameters on the hardness of melted zone in submerged arc welding by fuzzy logic", Journal of Mechanical Science and Technology, vol. 27, no. 7, pp. 2107-2113, 2013.