Synthesis and characterization of (Fe,Ti)3Al-Al2O3 nanocomposite via Fe2O3 reduction by Al

Subject Areas :

M.  Rafiei ¹ (Islamic Azad University, Najafabad Branch)
M.H.  Enayati ² (Isfahan University of Technology, Department of Materials Engineering)
F.  Karimzadeh ³ (Isfahan University of Technology, Department of Materials Engineering)

Received: 2016-04-20 Accepted : 2017-09-12 Published : 2017-08-23

Keywords: nanocomposite, Ball milling, DTA, Intermetallic Compound,

Abstract :

In this research the (Fe,Ti)3Al-Al2O3 nanocomposite was synthesized via the reduction of Fe2O3 by Al during mechanical alloying (MA). For this purpose the Al, Ti and Fe2O3 powders were mixed with molar ratio of 3:1:1in a planetary ball mill. The structural and morphology of powder particles during different milling times were characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). In order to study the thermal behavior of powder particles, Heat treatment and differential thermal analysis (DTA) were done. It was found that, the reaction of nanocomposite formation is occurred in two stages during MA. The first and second reactions were reduction of Fe2O3 by Al and (Fe,Ti)3Al formation, respectively. The crystallite size and internal strain of powder particles for Al2O3 phase after 100 h of MA, were 20 nm and 3%, respectively. Also ball milling for long time led to the reduction of Fe2O3 by Al before Al melting during DTA.

References:

 [1]    K. Matsuura, Y. Obara & M. Kudoh, “Fabrication of TiB₂ Particle Dispersed FeAl-based Composites by Self-propagating High-temperature Synthesisˮ, ISIJ. Int., Vol. 46, pp. 871–874, 2006.

 

[2]    B. G. Park, S. H. Ko, Y. H. Park & J. H. Lee, “Mechanical properties of in situ Fe₃Al matrix composites fabricated by MA–PDS processˮ, Intermetallics, Vol. 14, pp. 660-665, 2006.

 

[3]    A. V. Leonov, V. I. Fadeeva, O. E. Gladilina & H. Matyja, “Structure of Al50Ti50−xFex alloys prepared by mechanical alloying and subsequent annealing, Journal of Alloys and Compoundsˮ, Vol. 281, pp. 275–279, 1998.

 

[4]    S. M. Zhu, M. Tamura, K. Sakamoto & K. Iwasaki, “Effect of heating rate on the combustion synthesis of intermetallicsˮ, Mater. Sci. Eng, Vol. 292A, pp. 83–89, 2000.

 

[5]    R. T. Fortnum & D. E. Mikkola, “Effects of molybdenum, titanium and silicon additions on the DO3 ⇄ B2 transition temperature for alloys near Fe₃Alˮ, Mater. Sci. Eng, Vol. 91A, pp. 223–231, 1987.

 

[6]    M. G. Mendiratta, S. K. Ehlers & H. A. Lipsitt, “DO3-B2 phase relations in Fe- Al -Ti alloysˮ, Metall. Trans, Vol. 18A, pp. 509–518, 1987.

 

[7]    N. J. Welham, “Mechanical activation of the formation of an alumina-titanium trialuminide compositeˮ, Intermetallics, Vol. 6, pp. 363-368, 1998.

 

[8]    S. Schicker, D. E. Garcia, I. Gorlov, R. Janssen & N. Claussen, “Wet milling of Fe/Al/Al₂O₃ and Fe₂O₃/Al/Al₂O₃ powder mixturesˮ, J. Am. Ceram. Soc., Vol. 82, pp. 2607–2612, 1999.

 

[9]    D. Horvitz, I. Gotman, E. Y. Gutmanas & N. Claussen, “in situ processing of dense Al₂O₃–Ti aluminide interpenetrating phase compositesˮ, J. Eur. Ceram. Soc., Vol. 22, pp. 947–954, 2002.

 

[10] C. Suryanarayana, “Mechanical alloying and millingˮ, Prog. Mater. Sci., Vol. 46, pp. 1–184, 2001.

 

[11] R. Sedighi, M. Rajabi & S. M. Rabiee, “Synthesis and Thermal Stability of Nanocrystalline Mg-6Al-1Zn-1 Si Alloy Prepared Via Mechanical Alloyingˮ, Journal of Advanced Materials and Processing, Vol. 3, pp. 67-76, 2015.

 

[12]    ع، حیدری مقدم، ح، یوزباشی زاده، و. دشتی زاده و ع، کفلو، "سنتز ترکیب بین فلزی نانوساختار  Zr₃Coبا خاصیت جذب بالا به روش آلیاژسازی مکانیکی"، فصلنامه علمی پژوهشی فرایندهای نوین در مهندسی مواد، سال نهم، شماره سوم، پاییز 1394.

 

[13]    ع، حاج علیلو، ع، سعیدی و م. عباسی، "تولید کاربید تیتانیوم و نانوکامپوزیت TiC-Al₂O₃ با استفاده از روتیل به روش سنتز احتراقی و آلیاژسازی مکانیکی"، فصلنامه علمی پژوهشی فرایندهای نوین در مهندسی مواد، سال چهارم، شماره اول، بهار 1389.

 

[14] D. L. Zhang, Z. H. Cai & G. Adam, “The mechanical milling of Al/TiO₂ compositr powdersˮ, JOM, Vol. 56, pp. 53–56, 2004.

 

[15] M. Khodaei, M. H. Enayati & F. Karimzadeh, “Mechanochemically synthesized Fe₃Al–Al₂O₃ nanocompositeˮ, J. Alloys Compd., Vol. 467, pp. 159–162, 2009.

 

[16] M. Rafiei, M. H. Enayati & F. Karimzadeh, “Mechanochemical synthesis of (Fe,Ti)₃Al-Al₂O₃ nanocomposite, Journal of Alloys and Compoundsˮ, Vol. 488, pp. 144–147, 2010.

 

[17] G. K. Williamson & W. H. Hall, “X-ray Line Broadening from Filed Aluminium and Wolframˮ, Acta. Metall., Vol. 1, pp. 22–31, 1953.

 

[18] E. A. Brandes & G. B. Brook, “Smithells Metals HandBookˮ, Butterworth-Heinemann, Oxford, 1999.

 

[19] M. Rafiei, M. H. Enayati & F. Karimzadeh, “Characterization and formation mechanism of nanocrystalline (Fe,Ti)₃Al intermetallic compound prepared by mechanical alloyingˮ, Journal of Alloys and Compounds, Vol. 480, pp. 392–396, 2009.