Applying Nanocomposite Ni-B-ZrO2 Coating By Electroless Method on Steel CK45 and Study its Tribological Properties

Subject Areas :

yaser zakery nia ¹ , Reza Bazargan Lari ²

1 - دانشجوی دانشگاه آزاد واحد مرودشت
2 - استادیار، گروه مهندسی مواد دانشکده مهندسی، دانشگاه آزاد اسلامی، مرودشت، ایران

Received: 2016-09-12 Accepted : 2017-03-11 Published : 2017-02-19

Keywords: nanocomposite, Coating, ZrO2, electroless, Nickel – Boron,

Abstract :

Electroless nickel boron coatings usually due to wear and corrosion resistance that is well regarded. Electroless nickel boron through the chemical reduction of nickel ions on the surface of the catalytic caused and controlled until the solution is in contact with the reaction continues. In this study, Ni-B-ZrO2 nano composite coating was made by adding 4 g⁄l of ZrO2 nano particles to nickel – boron electroless solution on samples of CK45 steel; Then the coated samples heat treated for one hour at 400℃. The morphology and chemical compound was examined using SEM equipped by EDX. Electrochemical corrosion behavior of coatings in 3.5 showed by adding ZrO2nano particles the corrosion resistant of coatings improves. Electrochemical impedance spectroscopy showed that the coating after the heat treatment hadn't a protective effect And substrate are vulnerable to corrosion. Abrasion behavior by pin on disk test was measured at ambient temperature and Vickers hardness was measured by a micro hardness testing machine devices. The results showed that adding zirconia nanoparticles to the amount of 4g⁄l increased hardness and wear resistance of the coating. Coating composite samples of nickel - boron – zirconia without heat treatment the best results for the three parameters simultaneously high hardness, abrasion resistance and excellent corrosion resistance was good.

References:

 [1]       ج. گلاب و م. علیشاهی، "بهینه سازی عملیات حرارتی پوشش الکترولس Ni-P به کمک روش شناسی سطح پاسخ با هدف بهبود همزمان سختی و رفتار خوردگی"، فصلنامه علمی‌پژوهشی فرآیندهای نوین در مهندسی مواد شهر مجلسی، سال دهم، شماره اول، ص 197-206، بهار 1395.

 

[2]     W. Riedel, Electro less Plating, ASM International, Ohio, 1991.

 

[3]     Yancy W. Riddle, “Nickel-Boride (Ni3B) Plating”, UCT Coatings, ASM Metals HandBook, Vol. 5, 2005.

 

[4]     J. Park, “Bio ceramics: Properties, Characterizations, and Applications”, Springer, USA, 2008.

 

[5]     E. W. Brooman & Sh. L. Toepke, “BACKGROUND PAPER ON AEROSPACE & MISSILE NEEDS”, RDT&E Needs for the Metal Surface, Vol. 105, 2011

 

[6]     M. Anik, E. Körpe & E. Şen “Effect of coating bath composition on the properties of electro less nickel– boron films”, Surface & Coatings Technology, Vol. 202, pp. 1718–1727, 2008

 

[7]     K. Zielinska & A. Stankiewicz, “Electro less deposition of Ni-P-Zro2 Composite Coatings in the presence of various types of surfactants”, Journal of Colloid and Interface Science, Vol. 377, 2012.

 

[8]     World Wide Web page (no author), Zirconium Oxide (ZrO2) Nano powder / Nanoparticles Dispersion[online], Available from: URL:http://www.usnano.com/inc/sdetail/939, Accessed Sep, Vol. 12, 2016.

 

[9]       م، طاهری، ع. سالمی‌گلعذانی و ک. شیروانی، " تأثیر پوشش آلومینایدی بر رفتار خزشی سوپر آلیاژ پایه نیکلی GTD-111"، مجله مواد نوین مرودشت، شماره3، ص 68-61، بهار 1391.

 

[10]    م. بیدرام، ک. امینی، ع. شفیعی و م. بینا،" ایجاد پوشش کامپوزیتی نیکل- بور – کاربید تنگستن نانوکریستالی به روش الکترولس و بررسی خواص تریبولوژیکی آن"، فصلنامه علمی‌پژوهشی فرآیندهای نوین در مهندسی مواد شهر مجلسی، سال هفتم، شماره دوم، ص 23-17، تابستان1392.

 

[11] F. Delaunois, J. P. Petitjean, P. Lienard & M. Jacob-Duliere, “Autocatalytic electroless nickel-boron plating on light alloys”, Surface and Coatings Technology, Vol. 124, 2000.

 

[12] Baskaran, R. Sakthi Kumar, T. Sankara Narayanan & A. Stephen, “Formation of electro less Ni–B coatings using low temperature bath and evaluation of their characteristic propertiesˮ, Surf. Coat. Technol, Vol. 200, 2006.

 

[13] H. Hassan & Z. A. Hamid, “Electro less Ni–B supported on carbon for direct alcohol fuel cell applicationsˮ, Int. J. Hydrogen Energy, Vol. 36, 2011

 

[14] J. N. Balaraju & K. S. Rajam, “Electro less Deposition and Characterization of High Phosphorus Ni-PSi3N4 Composite Coatings”, International Journal of Electrochemical Society, Vol. 2, 2007.

 

[15] S. K. Das & P. Sahoo, “Influence of process parameters on micro hardness of electro less Ni–B coatingsˮ, Adv. Mech. Eng., 2012.

 

[16] T. Biestek, “Electro less Nickel Coatings: Testing of Corrosion and Wear Resistance”, Galvanotechnic, Vol. 88, No. 5, 1997.

 

[17] Z. A. Hamid, H. Hassan & A. Attyia, “Influence of deposition temperature and heat treatment on the performance of electro less Ni–B filmsˮ, Surf. Coat. Technol, Vol. 205, 2010

 

[18] T. Sankara Narayanan & S. Seshadri, “Formation and characterization of borohydride reduced electro less nickel depositsˮ, J. Alloys Comp, Vol. 365, 2004.

 

[19] J. Novakovic & P. Vassiliou, “Vacuum thermal treated electro less NiP–TiO2 composite coatingsˮ, Electro him. Acta, Vol. 54, 2009.

 

[20] S. Ranganatha, T. Venkatesha & K. Vathsala, “Development of electro less Ni–Zn–P/nano-TiO2 composite coatings and their propertiesˮ, Appl. Surf. Sci, Vol. 256, 2010.

 

[21] M. Momenzadeh & S. Sanjabi, “The effect of TiO2 nanoparticle code position on microstructure and corrosion resistance of electro less Ni–P coatingˮ, Mater. Corros, Vol. 63, 2012.