Accumulative press bonding: a novel process for manufacturing Al/ZnO metal matrix nanocomposites

Subject Areas :

سجاد امیرخانلو ¹ , محمد ابراهیم باجغلی ² , مصطفی کتابچی ³ , نادر پروین ⁴

1 - پسا دکتری- دانشگاه برونل لندن
2 - -
3 - -
4 - -

Received: 2016-01-19 Accepted : 2016-04-03 Published : 2017-02-19

Keywords: خواص مکانیکی, اکسید روی, پرس تجمعی پیوندی, نانوکامپوزیت زمینه فلزی, آلومینیم,

References:

 [1]     E. S. K. Kitazono&  K. Kuribayashi, “Novel manufacturing process of closed-cell aluminum foam by accumulative roll-bonding”, Scripta Mater, Vol. 50, pp. 495–498, 2004.

 [2]     S. H. Lee, T. Sakai, Y. Saito, H. Utsunomiya&  N. Tsuji, “Strengthening of sheath-rolled aluminum based MMC by the ARB process”, Mater. Trans, JIM, Vol. 40, pp. 1422-1428, 1999.

 

[3]     M. Alizadeh & M. H. Paydar, “Fabrication of Al/SiC P composite strips by repeated roll-bonding (RRB) process”, J. Alloys Compd, Vol. 477, pp. 811-816, 2009.

 

[4]     M. Alizadeh&  M. H. Paydar, “Fabrication of nanostructure Al/SiC P composite by accumulative roll-bonding (ARB) process”, J. Alloys Compd, Vol. 492, pp. 231-235, 2010.

 

[5]     M. Alizadeh&  M. H. Paydar, “High-strength nanostructured Al/B₄C composite processed by cross-roll accumulative roll bonding”, Mater. Sci. Eng., A, Vol. 538, pp. 14-19, 2012.

 

[6]     M. Alizadeh, M. H. Paydar&  F. Sharifian Jazi, “Structural evaluation and mechanical properties of nanostructured Al/B 4C composite fabricated by ARB process,” Composites Part B: Engineering, Vol. 44, pp. 339-343, 2013.

 

[7]     M. Alizadeh, M. H. Paydar, D. Terada&  N. Tsuji, “Effect of SiC particles on the microstructure evolution and mechanical properties of aluminum during ARB process”, Mater. Sci. Eng, A, Vol. 540,  pp. 13-23, 2012.

 

[8]     M. Alizadeh & M. Talebian, “Fabrication of Al/Cu p composite by accumulative roll bonding process and investigation of mechanical properties”, Mater. Sci. Eng, A, Vol. 558, pp. 331-337, 2012.

 

[9]     R. Jamaati, M. R. Toroghinejad & A. Najafizadeh, “An alternative method of processing MMCs by CAR process”, Mater. Sci. Eng, A, Vol. 527, pp. 2720-2724, 2010.

 

[10] R. Jamaati, M. R. Toroghinejad & A. Najafizadeh, “Application of anodizing and CAR processes for manufacturing Al/Al2O3 composite”, Mater. Sci. Eng, A, Vol. 527, pp. 3857-3863, 2010

 

[11] R. Jamaati, M. R. Toroghinejad, J. Dutkiewicz & J. A. Szpunar, “Investigation of nanostructured Al/Al 2O 3 composite produced by accumulative roll bonding process”, Mater. Des, Vol. 35, pp. 37-4, 2012.

 

[12] R. Jamaati & M. R. Toroghinejad, “Manufacturing of high-strength aluminum/alumina composite by accumulative roll is bonding”, Mater. Sci. Eng, A, Vol. 527, pp. 4146-4151, 2010.

 

[13] R. Jamaati & M. R. Toroghinejad, “Application of ARB process for manufacturing high-strength, finely dispersed and highly uniform Cu/Al 2O 3 composite”, Mater. Sci. Eng, A, Vol. 527, pp. 7430-7435, 2010.

 

[14] R. Jamaati & M. R. Toroghinejad, “High-strength and highly-uniform composite produced by anodizing and accumulative roll bonding processes”, Mater. Des, Vol. 31, pp. 4816-4822, 2010.

 

[15] S. Amirkhanlou, R. Jamaati, B. Niroumand & M. R. Toroghinejad, “Using ARB process as a solution for dilemma of Si and SiCp distribution in cast Al-Si/SiCp composites”, J. Mater. Process. Technol, Vol. 211, pp. 1159-1165, 2011.

 

[16] S. Amirkhanlou, R. Jamaati, B. Niroumand & M. R. Toroghinejad, “Fabrication and characterization of Al/SiCp composites by CAR process”, Mater. Sci. Eng., A, Vol. 528, pp. 4462-4467, 2011.

 

[17] S. Amirkhanlou, R. Jamaati, B. Niroumand & M. R. Toroghinejad, “Manufacturing of high-performance Al356/SiCp composite by CAR process”, Mater. Manuf. Processes, Vol. 26, pp. 902-907, 2011.

 

[18] S. Amirkhanlou & B. Niroumand, “Fabrication and characterization of Al356/SiCp semisolid composites by injecting SiCp containing composite powders”, J. Mater. Process. Technol, Vol. 212, pp. 841-847, 2012.

 

[19] S. Amirkhanlou, M. R. Rezaei, B. Niroumand & M. R. Toroghinejad, “Refinement of microstructure and improvement of mechanical properties of Al/Al2O3 cast composite by accumulative roll bonding process”, Mater. Sci. Eng, A, Vol. 528, pp. 2548-2553, 2011.

 

[20] C.Y. Liu, Q. Wang, Y. Z. Jia, B. Zhang, R. Jing, M. Z. Ma, Q. Jing & R. P. Liu, “Evaluation of mechanical properties of 1060-Al reinforced with WC particles via warm accumulative roll bonding process”, Mater. Des, Vol. 43, pp. 367-372, 2013.