Comparison of the Behavior of Martensitic and Ferrite Samples on Acoustic Emission Parameters
الموضوعات :Ramin Khamedi 1 , Mehdi Khosravi 2
1 - Department of Mechanical Engineering, Khazar University, Baku, Azerbaijan|Department of Mechanical Engineering, Zanjan University, Zanjan, Iran
2 - Department of Mechanical Engineering, Zanjan University, Zanjan, Iran
الکلمات المفتاحية: Acoustic Emission, Sentry Function, Martensitic, Fast Fourier Transform,
ملخص المقالة :
This study aimed to compared mechanical properties and failure mechanisms in ferrite and martensite samples, using Acoustic Emission (AE) Non-Destructive Testing (NDT). The purpose of this study is to identify the phases of ferrite and martensite by analyzing the parameters of AE. Tensile testing was performed on the samples and AE signals were recorded. The Sentry Function (SF) and Fast Fourier Transform (FFT) were used to analyze signals. The results of the martensite sample show that the SF is almost constant at the beginning. This indicates a relative balance between the AE energy and the strain energy. Then the SF took a downward state, which demonstrates a greater ratio of acoustic energy to strain energy. Frequency distribution, one of the best parameters to identify the failure mechanisms in materials for the ferrite sample, is significantly in the range of 175 kHz, while for the martensite sample, this range is between 520 and 700 kHz.
[1] Afsari, A., Fazel, D., Karimisharifabadi, J. and Mehrabi, V. 2020. Study the Percentage of Carbon and Ferrite in Layers of Steel (SA-516) by Strip Cladding with E316L. Journal of Modern Processes in Manufacturing and Production. 9(3): 41-50.
[2] Salari, M. 2019. Texture Evolution in Low Carbon Steel Fabricated by Multi-directional Forging of the Martensite Starting Structure. Journal of Modern Processes in Manufacturing and Production. 8(4): 5-15.
[3] Verhoeven, J. D. 2005. Metallurgy of steel for bladesmiths & others who heat treat and forge steel. Iowa State University. Ph.D. Thesis.
[4] Maki, T. 2012. Morphology and substructure of martensite in steels. Phase Transformations in Steels. Elesevier.
[5] Vahaviolos, S. J. 1999. Acoustic Emission: Standards and Technology Update (Vol. 1353). ASTM International.
[6] Khamedi, R., Fallahi, A. and Oskouei, A. R. 2010. Effect of martensite phase volume fraction on acoustic emission signals using wavelet packet analysis during tensile loading of dual phase steels. Materials & Design. 31(6): 2752-2759.
[7] Fallahi, A., Khamedi, R., Minak, G. and Zucchelli, A. 2012. Monitoring of the deformation and fracture process of dual phase steels employing acoustic emission techniques. Materials Science and Engineering. 548: 183-188.
[8] Van Bohemen, S. M. C., Sietsma, J., Hermans, M. J. M. and Richardson, I. M. 2003. Kinetics of the martensitic transformation in low-alloy steel studied by means of acoustic emission. Acta Materialia. 51(14): 4183-4196.
[9] Khamedi, R., Fallahi, A. and Zoghi, H. 2009. The influence of morphology and volume fraction of martensite on AE signals during tensile loading of dual-phase steels. International Journal of Recent Trends in Engineering. 1(5): 30-34.
[10] Khamedi, R., Fallahi, A., Refahi Oskouei, A. and Ahmadi, M. 2008. The effect of martensite phase volume fraction of dual-phase steels on acoustic emission signals under tensile loading. In 17th National Symposium on Ultrasonics Conference, Varanasi, India.
[11] Speich, G. R. and Schwoeble, A. J. 1975. Acoustic emission during phase. ASTM International. 571: 40-50.
[12] Rad, V. F., Khamedi, R. and Moradi, A. R. 2019. The effect of martensite volume fraction on topography of dual phase steels. Materials Letters. 239: 21-23.
[13] Kamel, S. M., Samy, N. M., Tóth, L. Z., Daróczi, L. and Beke, D. L. 2022. Denouement of the Energy-Amplitude and Size-Amplitude Enigma for Acoustic-Emission Investigations of Materials. Materials. 15(13): 4556.
[14] Ramalho, A., Santos, T. G., Bevans, B., Smoqi, Z., Rao, P. and Oliveira, J. P. 2022. Effect of contaminations on the acoustic emissions during wire and arc additive manufacturing of 316L stainless steel. Additive Manufacturing. 51: 102585.
[15] Speich, G. R. and Fisher, R. M. 1972. Acoustic emission during martensite formation. ASTM STP. 505: 140-151.
[16] Planes, A., Mañosa, L. and Vives, E. 2013. Acoustic emission in martensitic transformations. Journal of Alloys and Compounds. 577: 699-704.
[17] Khosravi, M. and Khamedi, R. 2022. Investigation of the effect of ferrite grain size on acoustic emission signals. Journal of Modern Processes in Manufacturing and Production. 11(3): 61-68.
[18] Bayram, A., Uǧuz, A. and Ula, M. 1999. Effects of microstructure and notches on the mechanical properties of dual-phase steels. Materials characterization. 43(4): 259-269.
[19] Dieter, P. P. 1988. Mechanical Metallurgy. McGraw-Hill Book. New York 1986.
[20] JH, H. and DM, L. 1999. Acoustic emission behavior during tensile tests of low carbon steel welds. ISIJ International. 39(4): 365-370.
[21] Huh, J. H., Lee, K. A. and Lee, C. S. 1997. Acoustic emission behavior during tensile deformation of welded steel joints. International Nuclear Information System. 45(29): 80-88.
[22] Raj, B., Jha, B. B. and Rodriguez, P. 1989. Frequency spectrum analysis of acoustic emission signal obtained during tensile deformation and fracture of an AISI 316 type stainless steel. Acta metallurgical. 37(8): 2211-2215.
[23] Casey, N. F., White, H. and Taylor, J. L. 1985. Frequency analysis of the signals generated by the failure of constituent wires of wire rope. NDT international. 18(6): 339-344.
