Texture Evolution in Low Carbon Steel Fabricated by Multi-directional Forging of the Martensite Starting Structuree
الموضوعات :
Mehdi Salari
1
(Department of Metallurgy, Sirjan Branch, Islamic Azad University, Sirjan, 8915685718, Iran)
الکلمات المفتاحية: Low Carbon Steel, Texture Evolution, Martensite Treatment, Multi-directional Forging, Plane Strain Compression,
ملخص المقالة :
It has been clarified that deformation and annealing of martensite starting structure can produce ultrafine-grained structure in low carbon steel. This study aims to investigate the texture evolution and mechanical properties of samples with martensite structure deformed by two different forging processes. The martensitic steel samples were forged by plane strain compression and multi-directional forging up to the same true strain of 2. All samples were then annealed at 450 and 550°C for 30 min. It was found that the active slip systems in the BCT crystalline structure of martensite acted like ferrite steel. After the multi-directional forging of martensitic steel, the yield and ultimate strength greatly increased to 1278 and 1658 MPa, respectively. During annealing, in the plane strain compressed sample, the "oriented nucleation" and in the multi-directional forged specimen, the "selective growth" theory was dominant.
[1] Berecz, T. P., Jenei, A., Csore, J., Labar, J. and Gubicza, P. 2016. Determination of dislocation density by electron backscatter diffraction and X-ray line profile analysis in ferrous lath martensite. Materials Characterization. 113: 117-204.
[2] Dastur, P., Zarei-Hanzaki, A., Pishbin M. H., Moallemi M. and Abedi H. R. 2017. Transformation and twinning induced plasticity in an advanced high Mn austenitic steel processed by martensite reversion treatment. Materials Science and Engineering: A. 696: 511-518.
[3] El-Tahawy, M., Henrique P., Pereira R., Huang, Y., Park, H. and Gubicza , J. 2018. Exceptionally high strength and good ductility in an ultrafine-grained Aluminium and Brass. Materials Letters. 214: 240-245.
[4] Ghosh, C., Haldar A. and Ghosh, P. 2008. Microstructure, Texture, Grain Boundary Characteristic. ISIJ International. 48: 1626-1631.
[5] Hosseini, M., kermanpur, A. and Najafizadeh, A. 2012. Effect of process parameters on microstructures and mechanical properties of a nano/ultrafine grained low carbon steel produced by martensite treatment using plane strain compression. ISIJ International. 52: 464-470.
[6] Jafarian H. and Tarazkouhi, M. 2017. Significant enhancement of tensile properties through combination of severe plastic deformation and reverse transformation in an ultrafine/nano grain lath martensitic steel. Materials Science and Engineering: A. 686: 113119
[7] Jafarian, H., Mousavi A., Eivani A. R. and Park N. 2017. A comprehensive study of microstructure development and its corresponding tensile properties in nano/ultrafine-grained metastable austenitic steel during accumulative roll bonding (ARB). Materials Science and Engineering: A. 703: 196-203.
[8] Jiang, H., Liu, Y., Wu, Y., Zhao, K., Shan, D. and Zong, Y. 2019. Grain Refinement Mechanism and Microstructural Evolution of M50NiL Steel during Multi-directional Impact Forging’, Journal of Materials Engineering and Performance, 12: 1-12.
[9] Kalashami, A., Kermanpur, A., Najafizadeh, A. and Mazaheri, Y. 2017. The effect of Nb on texture evolutions of the ultrafine-grained dual-phase steels fabricated by cold rolling and intercritical annealing. Journal of Alloys and Compounds. 694: 1026-1033.
[10] Kestens, L. and Pirgazi, H. 2016. Texture formation in metal alloys with cubic crystal structures. Materials Science and Technology. 32: 1303-1316.
[11] Kishchik, M.S, Mikhaylovskaya, A.V., Kotov, D., Mosleh, A.O., AbuShanab, W.S. and Portnoy, V.K. 2018. Effect of multidirectional forging on the grain structure and mechanical properties of the Al–Mg–Mn alloy. Materials, 11(11): 2166-2178.
[12] Markushev, M.V. 2011. On the methods of severe plastic deformation for bulk nano-materials processing. Letters on Materials, 1(1): 36-42.
[13] Mikhaylovskaya, A.V., Kotov, D., Kishchik, M.S., Prosviryakov, A.S. and Portnoy, V.K. 2019. The effect of isothermal multi-directional forging on the grain structure, superplasticity, and mechanical properties of the conventional Al–Mg-based alloy. Metals. 9: 33-45.
[14] Pereloma, E. and Edmonds, D. 2012. Phase transformations in steels, diffusionless transformations, high strength steels. modelling and advanced analytical techniques. Woodhead Publishing Limited.
[15] Yuan, Q., Xu, G., Liu, S., Liu, M., Hu. H and Li, G. 2018. Effect of rolling reduction on microstructure and property of ultrafine grained low-carbon steel processed by cryorolling martensite. Metals. 8: 518-532.
[16] Zheng, Z., Zhang, X., Xie, L., Huang, L. and Sun, T. 2019. Changes of microstructures and mechanical properties in commercially pure titanium after different cycles of proposed multi-directional Forging. Metals. 9:175-186.
