Investigating the effect of tool dimension and rotational speed on microstructure of Al-B4C surface composite layer produced by friction stir processing (FSP)

الموضوعات :

Mohammad Narimani ¹ , Behnam Lotfi ² , Zohreh Sadeghian ³

1 - Department of Materials Science and Engineering, Faculty of Engineering, Shahid Chamran University of Ahvaz, Ahvaz, Iran
2 - Department of Materials Science and Engineering, Faculty of Engineering, Shahid Chamran University of Ahvaz, Ahvaz, Iran
3 - Department of Materials Science and Engineering, Faculty of Engineering, Shahid Chamran University, Ahvaz, Iran.

تاريخ الإرسال : 16 الأربعاء , ربيع الأول, 1436 تاريخ التأكيد : 14 الأربعاء , رمضان, 1436 تاريخ الإصدار : 12 الأربعاء , جمادى الثانية, 1436

الکلمات المفتاحية: Friction stir processing (FSP), Aluminum matrix composite, B4C,

ملخص المقالة :

Friction stir processing (FSP) was used for the fabrication of Al-B4C surface composite. Al-Mg-Si alloy was considered as the substrate and B4C particles were incorporated into the substrate by thermo-mechanical effect of FSP. The effect of tool dimensions and different rotational speeds on the microstructure and microhardness of the composite layers was evaluated and the optimum process parameters were determined. Microstructural evaluation of the samples after FSP was conducted by optical microscopy (OM) and scanning electron microscopy (SEM) of the cross-sections of surface composite layers fabricated by FSP. Hardness profiles were obtained from microhardness measurements across the cross-sections of FSPed samples. The results showed that by increasing the tool size and rotational speed the size of nugget zone increases and the volume fraction of reinforcing particles decreases in FSPed samples. Moreover, composite layers containing higher volume fractions of B4C particles obtained from smaller tool size, exhibited higher values of hardness.

المصادر:

1. D. B. Miracle, “Metal matrix composites – From science to technological significance”, Compos Sci Technol, Vol. 65, 2005, pp. 2526–2540.


2. Cantor, B., Dunne, F. & Stone I, Metal and Ceramic Matrix Composites, Institute of Physics Publishing, IOP Publishing Ltd. (2004) First edition.


3. J. Qua, H. Xua, Z. Fenga, D. Alan Frederick, L. An, H. Heinrich, “Improving the tribological characteristics of aluminum 6061 alloy by surface compositing with sub-micro-size ceramic particles via friction stir processing”, Wear, Vol. 271, 2011, pp. 1940– 1945.


4. D. K. Lim, T. Shibayanagi, A. P. Gerlich, “Synthesis of multi-walled CNT reinforced aluminium alloy composite via friction stir processing”, Materials Science and Engineering A, Vol. 507, 2009, pp. 194-199.


5. M. Zohoor, M. K. Besharati Givi, P. Salami, “Effect of processing parameters on fabrication of Al–Mg/Cu composites via friction stir processing”, Materials and Design, Vol. 39, 2012, pp. 358–365.


6. Yong X. Gan, Structural assessment of nanocomposites, Micron, Vol. 43, 2012,
   pp. 782–817.


7. R. S. Mishra, & M. W, Mahoney, Friction Stir Welding and Processing, ASM International, (2007) First edition.


8. R. S. Mishra, Z. Y. Ma, I. Charit, “Friction stir processing: a novel technique for fabrication of surface composite”, Mater Sci Eng A, Vol. 341, 2003, pp. 307-310.


9. A. Shafiei-Zarghani, S. F. Kashani-Bozorg, A. Zarei- Hanzaki, “Wear assessment of Al-Al2O3 nano-composite surface layer produced using friction stir processing”, Wear, Vol. 270, 2011, pp.403–412.


10. A. Dolatkhah, P. Golbabaei, M. K. Besharati Givi, F. Molaiekiya. “Investigating effects of process parameters on microstructural and mechanical properties of Al5052/SiC metal matrix composite fabricated via friction stir processing.”, Materials and Design, Vol. 37, 2012, pp.458-464.


11. M. Barmouz, P. Asadi, M. K. Besharati Givi, M. Taherishargh, “Investigation of mechanical properties of Cu/SiC composite fabricated by FSP: Effect of SiC particles’ size and volume fraction”, Materials Science and Engineering A,Vol.528, 2011, pp. 1740-1749.


12. M. Barmouz, M. K. Besharati Givi, J. Seyfi, “On the role of processing parameters in producing Cu/SiC metal matrix composites via friction stir processing: Investigating microstructure, microhardness, wear and tensile behavior”, Mater Charact, Vol. 62, 2011, pp. 108–117.


13. M. Khakbiz, F. Akhlaghi, “Synthesis and structural characterization of Al–B4C nano-composite powders by mechanical alloying”, J Alloy Compd, Vol. 479, 2009, pp. 334-341.


14. T. Ya. Kosolapova, Carbides: properties, production and applications, (1971) plenum press First edition.


15. N. Yuvaraj, S. Aravindan, Vipin, “Fabrication of Al5083/B4C surface composite by friction stir processing and its tribological characterization” J Mater Res Tech, In press, doi:10.1016/j.jmrt. 2015.02.006


16. F. Frigaard, F. Grong, O. T. Midling, “A Process Model for Friction Stir Welding of Age Hardening Aluminum Alloys”, Metall Mater Trans A, Vol. 32(5), 2001, pp. 1189-1200.


17. Y. G. Kim, H. Fujii, T. Tsumura, T. Komazaki, K. Nakata, “Three defect types in friction stir welding of aluminum die casting alloy”, Mater Sci Eng A, Vol. 415, 2006, pp. 250–254.


18. R. Nandan, T. DebRoy, H.K. Bhadeshia, “Recent advances in friction-stir welding-Process, weldment structure and properties”,Prog Mater Sci, Vol. 53, 2008, pp. 980-1023.


19. K. Elangovan, V. Balasubramanian, “Influences of tool pin profile and tool shoulder diameter on the formation of friction stir processing zone in AA6061 aluminium alloy”, Mater Design, Vol. 29, 2008, pp. 362-373.


20. E. Salari, M. Jahazi, A. Khodabandeh, H. Ghasemi-Nanesa, “Influence of tool geometry and rotational speed on mechanical properties and defect formation in friction stir lap welded 5456 aluminum alloy sheets”, Mater Design, Vol. 58, 2014, pp. 381-389.


21. M. Sharifitabar, A. Sarani, S. Khorshahian, M. Shafiee Afarani, Fabrication of 5052Al/Al2O3 nanoceramic particle reinforced composite via friction stir processing route, Mater Design, Vol. 32, 2011, pp. 4164-4172.


22. A. Devaraju, A. Kumar, B. Kotiveerachari, “Influence of addition of Gr/Al2O3 with SiC on wear properties of aluminum alloy 6061-T6 hybrid composites via friction stir processing”, T Nonferr Metal Soc, Vol.23, 2013, pp.1275-1280.


23. A. Devaraju, A. Kumar, A. Kumaraswamy, B. Kotiveerachari, “Wear and mechanical properties of 6061-T6 aluminum alloy surface hybrid composites [(SiC + Gr) and (SiC + Al2O3)]fabricated by friction stir processing”, J Mater Res Technol, Vol. 2(4), 2013,pp. 362-369


24. R. Sathiskumar, N. Murugan, I. Dinaharan, S. J. Vijay, “Effect of Traverse Speed on Microstructure and Microhardness of Cu/B4C Surface Composite Produced by Friction Stir Processing”, T Indian Inst Metall, Vol. 66(4), 2013, pp. 333-337.


25. S. Shahraki, S. Khorasani, R. A. Behnagh, Y. Fotouhi, H. Bisadi, “Producing of AA5083/ZrO2 Nanocomposite by Friction Stir Processing (FSP)”, Metall Mater Trans B, Vol. 44(6), 2013, pp. 1546-1553.


26. D. J. Lloyd, “Particle reinforced aluminum and magnesium matrix composites”, Int Mater Rev, Vol. 39, 1994, pp. 1-24.