Scientific Evaluation of Advanced Materials in Automotive Design with a Focus on Weight Reduction and Environmental Impact
الموضوعات : Journal of Environmental Friendly Materials
A Bonyadi Naeini
1
,
E Anbarzadeh
2
1 - Faculty of Industrial Engineering, Sharif University of Technology, Tehran, Iran
2 - School of Mechanical Engineering, Iran University of Science and Technology, Tehran, Iran
الکلمات المفتاحية: Numerical Modeling & Optimization, Sustainable Materials, Lightweight Design, Environmental Sustainability,
ملخص المقالة :
This study presents a multi-objective optimization approach to automotive body material selection that seeks to trade-off mechanical performance, cost savings, and environmental sustainability. Utilizing advanced numerical modelling and experimental verification, 45 different materials, including metals, composites, and polymers, were evaluated on the basis of strength-to-weight ratio, hardness-to-cost efficiency, and environmental friendliness. The findings indicate that carbon fiber composite, titanium alloys, and hybrid polymer-metal structures are the optimal materials for light yet strong automotive parts, such that fuel efficiency can be increased by up to 12%. Environmental research indicated that natural fiber composites and aluminum-polymer hybrids significantly reduce CO₂ emissions and energy demands and facilitate global trends toward eco-friendly vehicle manufacturing. Despite budget and scalability problems in integrating high-performance recycled content, the study points to spurring innovation in future lightweight automobile development, focusing on the part that data-driven material selection methods play in reducing carbon footprints and improving vehicle efficiency
[1] Karami M, Anbarzadeh E. Optimizing the Insulation Thickness of the Building in Different Climatic Conditions with an Environmental Approach. Build. Eng. & Hou. Sci. 2020; 13(4):1-5.
[2] Karami M, Anbarzadeh E, Delfani S. Effect of HVAC system size on the optimum insulation thickness of the buildings in different climate zones. J. Therm. Eng. 2021 ;8(2):249-67.
[3] Anbarzadeh E, Ghafoori Yazdi SM. Environmental Optimization of Building Insulation Thickness in Warm-Dry Regions. J. Envi. Friend. Mat.(JEFM). 2019 ;3(2):11-5.
[4] Anbarzadeh E, Shahmohammadi T. Environmental Optimization of Building Insulation Thickness for Cold Climates using Neural Network Method. J. Envi. Friend. Mat. (JEFM).2020 ;4(1):37-42.
[5] Anbarzadeh A, Nejad MG, Mirzamohammadi S, Geravand SA. An Investigation on the Extraction of High-Carbon Ferrochrome with an Environmental Approach. J. Envi. Friend. Mat. (JEFM)2022 ;6(2):27-30.
[6] Sadeghi M. New Approach to Assessing of High-Strength SG Cast Iron for Environmentally Clean Energy Technology. J. Envi. Friend. Mat. (JEFM). 2022 ;6(1):01-5.
[7] Anbarzadeh A, Tahavvori R. Sustainable Development by Green Engineering Materials. J. Envi. Friend. Mat. (JEFM). 2019 ;3(1):49-53.
[8] Bakhtiari H, Abbasi H, Sabet H, Khanzadeh MR, Farvizi M. Investigation on the Effects of Explosive Welding Parameters on the Mechanical Properties and Electrical Conductivity of Al-Cu Bimetal. J. Envi. Friend. Mat. (JEFM). 2022 ;6(2):31-7.
[9] Sabet H. Evaluation Microstructure and Hardness of the Fe-Cr-C Hardfacing Alloy with Cr/C= 6 Ratio. J. Envi. Friend. Mat. (JEFM).2021 ;5(2):35-43.
[10] Ashkani O, Tavighi MR, Sabet H. Recent Developments of Quantum Science in Laser Technologies, a Mini-Review. J. Envi. Friend. Mat. (JEFM). 2024 ;8(2):43.
[11] Mohammadi B, Anbarzadeh E. Evaluation of viability and cell proliferation in bone and gingival on dental implant fixtures with active sandblasted and sandblasted surfaces by the cytotoxicity test method. J. of Bio. Biomat and Biomed. Eng. 2022 ;6:165-72.
[12] Anbarzadeh E, Mohammadi B. Improving the surface roughness of dental implant fixture by considering the size, angle and spraying pressure of sandblast particles. J. Bion. Eng. 2024 ;21(1):303-24.
[13] Li L, He X, Keoleian GA, Kim HC, De Kleine R, Wallington TJ, Kemp NJ. Life cycle greenhouse gas emissions for last-mile parcel delivery by automated vehicles and robots. Envir. Sci. tech. 2021 ;55(16):11360-7.
[14] Anbarzadeh E, Mohammadi B, Azadzaeim M. Effects of acid etching parameters on the surface of dental implant fixtures treated by proposed coupled SLA-anodizing process. J. Mat. Res. 2023 ;38(22):4951-66.
[15] Lammert MP, Duran A, Diez J, Burton K, Nicholson A. Effect of platooning on fuel consumption of class 8 vehicles over a range of speeds, following distances, and mass. SAE Int. J. Comm. Veh. 2014 ;7(2014-01-2438):626-39.
