Investigating the Microstructure and Mechanical Properties of Tantalum Sintered Parts by Hot Pressing in a Vacuum

الموضوعات : Materials synthesis and charachterization

Farrokh Najafzadegan ¹ , Alireza Khodabandeh ² , Hossein Yoozbashizadeh ³ , Morteza Tamizifar ⁴

1 - Department of Materials Science and Engineering, Science and Research Branch, Islamic Azad University, Tehran, Iran.
2 - Department of Materials Science and Engineering, Science and Research Branch, Islamic Azad University, Tehran, Iran.
3 - Department of Materials Science and Engineering, Sharif University of Technology, Tehran, Iran.
4 - School of Metallurgy and Materials Engineering, Iran University of Science and Technology, Narmak, Tehran, Iran.

تاريخ الإرسال : 20 الجمعة , شوال, 1446 تاريخ التأكيد : 23 الإثنين , ربيع الأول, 1447 تاريخ الإصدار : 16 الأحد , ربيع الأول, 1445

الکلمات المفتاحية: Tantalum, Hot Pressing, Ductility, Mechanical Properties,

ملخص المقالة :

This study investigates the consolidation of pure tantalum powder via hot pressing (HP) to enhance its ductility and mechanical properties. The effects of sintering temperature and time on the microstructure and mechanical properties of sintered tantalum were examined. Density was measured using the Archimedes method, while microstructure was analyzed via optical and scanning electron microscopy. Compression tests evaluated mechanical properties. Results revealed that reduced porosity and altered porosity morphology significantly improved mechanical properties. A 17.6% density increase led to a 100% enhancement in compressive strength, ductility, and hardness. Optimal properties were achieved at 1600°C, yielding a hardness of 345 HV, compressive strength of 1278 MPa, and ductility of 34%.

المصادر:

[1] Lambert, J.B, “Properties and Selection: Nonferrous Alloys and Special-Purpose Materials”, ASM Handbook, Vol. 2, (1990), 1698-1701.
[2] Cardonne SM, Kumar P,Muchaluk CA, Schwartz HD, “Tantalum and its alloys”, Int J Refract Met Hard Mater, 13, (1995), 187–94.
[3] Lambert, J.B, “Properties and Selection: Nonferrous Alloys and Special-Purpose Materials”, ASM Handbook, Vol. 2, (1990), 557-585.
[4] Buckman Jr RW, “New Applications for Tantalum and Tantalum Alloys”, J Miner Met Mat Society, 52, 3, (2000), 40-41.
[5] Burns RH, Fang JC, Kumar P, “Evolution of applications of tantalum”, Proc 125th TMS AnnualMeeting and Exhibition, (1996), 273–85.
[6] Chou, PC, Crudza, ME, “The effects of liner anisotropy on warhead performance”, Warrendale PA TMS, (1992), 97–109.
[7] Muller JF, Dinh, PM, “Evaluation of powder metallurgy tantalum liners for explosively formed penetrator”, Proc 2nd Int Conf Tungsten Refract Met,(1994), 573–86.
[8] Flater P, House J, O'Brien J, HosfordWF, “High strain rate properties of tantalum processed by equal channel angular pressing”, Air Force Research Laboratory Technical Report, (2007), 7412.
[9] W. Brian James, Hoeganaes Corporation, retired, “Powder Metallurgy Methods and Application”, ASM Handbook, Vol. 07, ( 2015), 1424-1445.
[10] Yoo SH, Sudarshan TS, Sethuram K, Subhash G, Dowding RJ, “Consolidation and high strain rate mechanical behavior of nanocrystalline tantalum powder”, Nanostruct Mater, 12, (1999), 23–8.
[11] Mert Efe, Hyun Jun Kim, Srinivasan Chandrasekar, Kevin P. Trumble, “The chemical state and control of oxygen in powder metallurgy tantalum”, Materials Science and Engineering, A, 544, (2012), 1– 9.
[12] Stecura, S, Metall. Trans, 5, (1974), 1337–1340.
[13] Droegkamp R.E, Schussler M, Lambert J.B, Taylor D.F, Encyclopedia of Chemical Technology, vol. 22, (1984), 541–564.
[14] Mann J.B, Saldana C, Chandrasekar S, Compton W.D, Trumble K.P, Scr. Mater, 57, (2007) , 909–912.
[15] Angerer P, Neubauer E, Yu LG, Khor KA, “Texture and structure evolution of tantalum powder samples during spark-plasma-sintering and conventional hot-pressing”, Int J Refract Met Hard Mater, 25, (2007), 280–5.
[16] Angerer P, Artner W, Neubauer E, Yu LG, Khor KA, “Residual stress in spark-plasma-sintered and hot-pressed tantalum samples determined by X-ray diffraction methods”, International Journal of Refractory Metals & Hard Materials, 26, (2008), 312–317.
[17] Khorsand, H.; Abdoos, H. (2015). Mechanical and Fatigue Behavior of Sintered Porous Parts. Tehran: University of Khajeh Nasirodin Toosi. (In Persian)
[18] Sinthu Chanthapan, “sintering of refractory metal based materials by firld assisted sintering technology (FAST) ”,Doctoral dissertation in material science, Pennsylvania State University,)2012(.
[19] Brown AM, Ashby MF, “ Correlations for Diffusion Constants”, Journal of Acta Metallurgica, (1980), 1085.
[20] German R M, “Sintering Theory and Practice”. New York: John Wiley and Sons,( 1996).
[21] Xu Q, Hayes RW, Lavernia EJ. “Creep properties of ball-milled and HIPed pure tantalum”.Scr Mater (2001),45, 447–54.
[22] Filgueira M, Pinatti DG, De Holanda JNF, Gomes UU. “Densification and mechanical properties of liquid phase sintered tantalum”. Mat-wiss, u Werkstofftech, (2009), 40, 784-790.
[23] Funkeler FJ, “ Fabricated tantalum from unsintered HIP powder”, Tungsten and refractory metals, Proc 2nd Int Conf Tungsten Refract Met, MPIF: McLean; October (1994), 531–46.
[24] Boncoeur M, Valin F, Raisson G, Michaud H. “Properties of hot isostatically pressed tantalum. Hot isostatic pressing-theory and applications”, Proc 3rd Int Conf Hot Isostatic Pressing, Osaka, Springer, (1991), 247–52.
[25] Bingert SR, Vargas VD, Sheinberg H, “Tantalum powder consolidation, modeling and properties Tantalum”, Proc 125th TMS Annual Meeting and Exhibition, Anaheim TMS, (1996), 95–105.
[26] Youngmoo Kim, “Fabrication and mechanical properties of powder metallurgy tantalum prepared by hot isostatic pressing”, Int. Journal of Refractory Metals and Hard Materials, (2015),48, 211–216.