Experimental Investigation of Heat Treatment Effects on Mechanical Properties and Microstructure of AA6063 Alloy in ECAP Process
الموضوعات :Hossein Tamim 1 , Mohammad Javad Saleh Parhizkar 2
1 - Islamic Azad University, Arak Branch
2 - of Mechanical Engineering, Saveh Branch, Islamic Azad University, Saveh, Iran
الکلمات المفتاحية: Plastic deformation, Ultra finely grained structure, Equal Channel Angular Pressing (ECAP), Mechanical properties, Microstructure,
ملخص المقالة :
Severe Plastic Deformation (SPD) methods have gained significant attention in modern metal forming due to their ability to create desirable microstructures. One highly regarded SPD method is Equal Channel Angular Pressing (ECAP), which induces substantial shear strain to refine grains during the forming process and subsequent recrystallization. Numerous factors influencing ECAP's efficiency and material quality have been subjects of extensive research. This study investigates the effects of various heat treatment cycles on the mechanical properties and microstructure of 6063 AA alloy subjected to ECAP. The ECAP process was performed up to 4 passes at room temperature, following the BC route for aluminum samples of 6063 AA. Additionally, the combination of ECAP and in-passe aging heat treatment was examined. To evaluate the mechanical properties and microstructural changes, tensile and hardness tests along with Scanning Electron Microscopy (SEM) were utilized. Results indicated a significant increase in strength and hardness, coupled with a reduction in elongation, attributed to work hardening and grain refinement. SEM images confirmed ECAP's effectiveness in producing ultrafine grains. Overall, natural aging for 30 days post-ECAP showed no effect on mechanical properties compared to immediate solutionizing and subsequent ECAP. For applications requiring high strength and substantial elongation, artificial aging post-ECAP is recommended.
[1] A.I.Gusev, A.A.Rempel, Nanocristalline materials, Cambridge international science publishing, 2004.
[2] V.M.Segal, Equal channel angular extrusion: from macro mechanics to structure formation, journal of Materials Processing Technology, 141(2003) 313-318.
[3] Valiev, R.Z., Islamgaliev, R.K., Alexandrov, I.V., "Bulk nanostructured materials from severe plastic deformation" Progress in Materials Science 45 (2000) 103–189.
[4] Han BQ, Matejczyk D, Zhou F, Zhang Z, Bampton C, Lavernia EJ, et al. “Enhancement of mechanical properties and grain size refinement of commercial purity aluminum 1050 processed by ECAP”, Metal Mater Trans 2004; 35A :947.
[5] ASM, Vol. 103,104.
[6] Donald R.Askeland, The Science and Engineering of Materials, Chapman & Hall Third Ed, 1996.
[7] Bridgman PW. “Studies in large plastic flow and fracture” New York, NY, USA: McGraw-Hill; 1952.
[8] Sieber H., Wilde G., Perepezko J.H., “Thermally activated amorphous phase formation in cold-rolled multilayers of Al-Ni, Al-Ta, Al-Fe and Zr-Cu”, Journal of Non-Crystalline Solids Vol. 250-252, 1999,pp.611-615.
[9] Shingu P.H., Ishihara K.N., Otsuki A., Daigo I., “Nano-scaled multi-layered bulk_ materialsmanufactured by repeated pressing and rolling in the Cu–Fe system”, Materials Science and Engineering.A, Vol. 304–306, 2001, pp. 399–402.
[10] Terence G.Longdon, ”The Principles of Grain Refinement In Equal-Channel Angular pressing”, Materials Sience and Engineering, 2007, Vol.A, No.462, P.3-11.
[11] G.Ramu, Rangit Bauri, ”Effect of Equal-Channel Angular Pressing on Microstructure and Properties of AL-SIC Composite”, Materials and Design, 2009, No.3, P.3554-3559.
[12] Nobohiro Tsuji, Yoshihiro Saito, Seong-Hee Lee, Yoritoshi Miniamino, ”Accumulative Roll-Bonding and other New Techniques to Produce Bulk Ultrafine Grained Materials”, Advanced Engineering Materials, 2003,2005, No.5, P.340-343.
[13] Q.D.Wang, Y.J.Chen, J.B.Lin,L.J.Zhang, C.Q.Zhai, ”Microstructure and Properties of Magnesium Alloy Processed by a New Severe Plastic Deformation Method”, Matarials Latters, 2007, No.61, P.4599-4602.
[14] N.Pardis,R.Ebrahimi, ”Deformation Behavior in Simple Shear Extrusion (SSE) as a New Severe Plastic Deformation Technique”, Materials Science and Engineering, 2009, Vol.A, No.527, P.355-360.
[15] Qiang Chen, Zhixiang Zhao, Dayu Shu, Zude Zhao, ”Microstructure and Mechanical Properties of AZ91D Magnesium alloy Prepared by Compound Extrusion”, Materials Science and Engineering, 2011, Vol.A, No.528, P.3930-3934.
[16] M.Jahedi, M.H.Paydar, ”Study on the Feasibility of Extrusion (TE) Process as a Severe Plastic Deformation Method for Consolidation of AL powder”, Materials Science and Engineering, 2010, Vol.A, No.527, P.5273-5279.
[17] Radim Kocich, Miroslav Kursa, Ivo Szurman, Adela Machackova, ”Twist Channel Angular Pressing (TCAP) as a Method for increasing the Efficiency of SPD”, Materials Science and Engineering, 2010, Vol.a, No.527, P.6386-6392.
[18] A.Zangiabadi, M.Kazeminezhad, ”Development of a novel Severe Plastic Deformation Method for Tubular Materials: Tube Channel Pressing (TCP)”, Materials Science and Engineering, 2011, Vol.A, No.528, P.5066-5072.
[19] S.M.Fatemi-Varzaneh, A.Zarei-Hanzaki, ”Processing of AZ31 Magnesium alloy by a New noble Severe Plastic Deformation Method”, Materials Science and Engineering, 2011, Vol.A, No.528, P.1334-1339.
[20] Y.T.Zhu, T.C.Lowe, T.G.Langdon, scripta mater, 51 (2004) 825.
[21] G.J.Raab, R.Z.Valiev, T.C.Lowe, Y.T.Zhu, Mater, Sci, Eng,a 382 (2004).
[22] A.Azushima, K.Aoki, Mater, Sci, Eng, A 337 (2002) 45.
[23] Iwahashi Y, Wang J, Horita Z, Nemoto M, Langdon TG., “Principle of equal-channel angular pressing for the processing of ultra-fine grained materials” Scripta Mater 1996;35:143.
[24] Horita Z, Langdon TG.,” The evolution of homogeneity in an aluminum alloy processed using high-pressure torsion”, Acta Materialia, Volume 56, Issue 18, October 2008, Pages 5168-5176.
[25] Yuntian T. Zhu, Terry C. Lowe, Terence G. Langdon, “Performance and applications of nanostructured materials produced by severe plastic deformation”, Scripta Materialia 51 (2004) 825–830.
[26] Verlinden Bert, “SEVERE PLASTIC DEFORMATION OF METALS”, UDC: 669 .01 :620 .174/.175=20.
[27] Wang J. T., Xub C., Duc Z. Z., Qua G. Z., Langdon T. G., Microstructure and properties of a low-carbon steel processed by Equal channel angular pressing, Mater. Sci. Eng. A410-411 (2005).
[28] T.G. Langdon, 2006, the principles of by Equal channel angular pressing, Mater. Sci. Eng. A410-411.
[29] C.Y. Yu, P.L.Sun, P.W. Kao, Mechanical properties of submicron-grained aluminum, Scripta Materials 53 (2005) 647-652.
[30] Iwahashi Y., wang j., Horita z.,Nemoto M., Langdon T. G., Scripta Mater. 35(1996)143.
[31] P.K Chaudhury et al. Scaling up of Equal channel angular pressing and its effect on mechanical properties, microstructure & hot workability of AA6061, Materials Science & engineering A. Vol 410-411, 25nov 2005, 316-378.
[32] H.Utsunomiya, Continuous grain refinement of aluminum strip by conshearing, Materials Science and Engineering A 372 (2004) 199-206.
[33] Georgy j. Raab,et al. Continuous Processing of ultrafine grained AL by ECAP-Conform, Materials Science and Engineering A 382 (2004) 30-34.
[34] Kim H.S., Seo M.H., Hong S.L., Plastic deformation analysis of metals during Equal channel angular pressing, J.Mater. Proc. 113 (2001) 622-626.
[35] Pei Q.X., Hu B.H., Lu C., Wang Y.Y., A finite element study of the temperature rise during Equal channel angular pressing, Scripta mat. 49 (2003) 303-308.
[36] Nagasekhar A.V., Tick-Hon Y., Lib S., Seow H.P., Effest of acute tool-angles on Equal channel angular extrusion/pressing, Mater. Sci. Eng. A410-411 (2005) 269-272.
[37] Zhao G, Xu S, Luan Y, Guan Y, Lun N, Ren X, Grain refinement mechanism analysis and experimental investigation of Equal channel angular pressing for producing pure aluminum ultra-fine grained materials, Materials Science and Engineering A 437 (2006) 281-292.
[38] W.J Kim, J.Y. Wang, Microstructure of the post-ECAP aging processed 6061 AL alloys, Materials Science and Engineering A 464 (2007) 23-27.
[39] W.J.Kim, Y.K.Sa, H.K.Kim, U.S.Yoon, Plastic forming of the equal-channel angular pressing, processed 6061 aluminum alloy, Materials Science and Engineering A , 487 (2008), 360–368.
[40] Gutierrez-Urrutia I, Morris M.A, Morris D.G, Contribution of microstructure parameters to strengthening in an ultrafine-grained AL-7% Si alloy processed by severe deformation, Acta Materials 55 (2007)n1319-1330.
